Same-day dispatch before 2 PM · Free delivery over ₹999 · GST invoices Get the appPrices incl. GST
Geekobot
Snap & SendNEWGeeko AIWhere's myOrder
Log in
Products
  • Projects
    • Component guidesHow parts work, with code you can run
    • Learning pathsFrom your first LED to your first robot
    • Workshops & eventsOnline sessions for makers and classes
    • ElectrolarkFree guided builds, simulator and certificates
    • Students & teachersStudent discount and classroom help
    • CommunityShare builds and ask other makers
    • CalculatorsOhm's law, LED resistor, 555 and 100+ more
    • Circuit builderWire parts and run the circuit, powered by Electrolark
    • Geeko AIAsk what to buy or how to wire it
    • Snap & SendPhotograph a part or list, we find it
    • Part finderAnswer a few questions, get the right part
    • Compatibility checkWill these two parts work together?
    • Compare partsSpecs side by side
    • Business & bulk ordersGST invoices, credit and volume prices
    • Request a quotationSend your list, get a quote
    • Classroom kitsPer-student kits and lab bundles
    • Gift cardsFor students, teams and events
  • Atal Tinkering Lab
BOM to cart
Geekobot

Components, kits and know-how for makers, students, engineers, labs and businesses across India.

Ask Geeko AIOrders, parts and projects, any timeEmail supportReply within 1 working dayGet the Geekobot appAdd it to your home screen, free

Follow us

Shop

  • Boards & SBCs
  • Sensors & Modules
  • IoT & Wireless
  • Drone & FPV
  • 3D Printing
  • Filaments & Resins
  • Motors & Drivers
  • Power & Batteries
  • Semiconductors
  • Passive
  • Displays & LEDs
  • Switches & Relays
  • Wires & Cables
  • Prototyping
  • Tools & Test
  • Robotics
  • STEM Kits
  • Atal Tinkering Lab
  • Mechanical Parts
  • Audio

Orders

  • Track your order
  • Help & support
  • Shipping and delivery
  • Refunds and cancellation
  • Contact us

Learn

  • Projects
  • Geeko AI project assistant
  • Learning paths
  • Guides
  • Calculators
  • Electrolark: free guided builds

Part tools

  • Part finder
  • Compare parts
  • Will it work with my board?

Institutions

  • Classroom kits
  • Atal Tinkering Lab
  • Students & teachers
  • Workshops & Events

Business

  • Business & education
  • Request a quotation
  • BOM bulk upload
  • Quick order by SKU

Company

  • About Geekobot
  • Community
  • Gift cards
  • Terms & conditions
  • Privacy policy
  • Product directory
  • Sitemap

© 2026 Geekobot, a trade name of OLatus Systems Private Limited. All rights reserved.

20, 1st Floor, Neeladri Complex, 10th Cross, Sampige Rd, 2nd Main, Malleshwaram, Bengaluru, Karnataka 560003 · GSTIN 29AACCO0462F1ZM

+91 91810 15607 · connect@geekobot.in · Monday to Saturday, 10 AM to 2 PM IST

UPI · CARDS · NETBANKING · GST INVOICES

ShopProjectsGeeko AIGuides
Compare 0 parts →
Log in

Shop by category

Shop all components
  • Boards & SBCs1,910 products
    • Alternative Single Board Computers
    • Arduino Ecosystem
    • FPGA & Logic Boards
    • Microcontroller & Wireless Boards
    View all
  • Sensors & Modules4,701 products
    • Biomedical & Heart Rate
    • Current, Voltage & Power
    • Force, Weight & Pressure
    • Gas, Weather & Environmental
    View all
  • IoT & Wireless2,314 products
    • RF Modules
    • RFID & NFC
    • Antennas & RF Accessories
    • Cameras & Smart Vision
    View all
  • Drone & FPV3,558 products
    • Flight Control & Navigation
    • FPV Video & Optics
    • Frames & Structural Parts
    • Motors & Propulsion
    View all
  • 3D Printing2,204 products
    • 3D Printers
    • 3D Scanners & Digitizers
    • Laser Engravers & Cutters
    • Material Management & Upgrades
    View all
  • Filaments & Resins1,472 products
    • Filaments
    • Photopolymer Resins
    View all
  • Motors & Drivers463 products
    • BLDC Motor Drivers
    • DC & Geared Motors
    • DC Motor Drivers
    • Linear Actuators & Solenoids
    View all
  • Power & Batteries557 products
    • Battery Holders & Connectors
    • Breadboard Power
    • Chargers & BMS
    • DC-DC Converters
    View all
  • Semiconductors295 products
    • Diodes & Rectifiers
    • Interface & RF Encoder ICs
    • Logic ICs (74xx)
    • Logic ICs (CD4000)
    View all
  • Passive67 products
    • Capacitors
    • Circuit Protection
    • Crystals & Oscillators
    • Inductors
    View all
  • Displays & LEDs572 products
    • 7-Segment & Dot Matrix
    • Addressable LEDs
    • Character LCDs
    • Graphic LCDs
    View all
  • Switches & Relays184 products
    • Keypads & Touch
    • Push Buttons & Tactile
    • Relay Modules
    • Relays
    View all
  • Wires & Cables233 products
    • Board-to-Wire Connectors
    • Crimp & Splice
    • Headers & Dupont
    • Heat Shrink & Sleeving
    View all
  • Prototyping101 products
    • Breadboards
    • Interface Modules
    • PCBs & Perfboards
    View all
  • Tools & Test717 products
    • Bench Power Supplies
    • Hand Tools
    • Measuring Tools
    • Meters & Testers
    View all
  • Robotics180 products
    • Humanoid & Legged Robots
    • Robot Chassis & Platforms
    • Robotic Arms & Grippers
    • Wheels & Casters
    View all
  • STEM Kits268 products
    • Arduino Learning Kits
    • Coding & IoT Kits
    • Early Coding (Ages 3-8)
    • Invention Kits
    View all
  • Atal Tinkering Lab196 products
    • Package 1: Electronics, Robotics, IoT and Sensors
    • Package 2: Rapid Prototyping Tools
    • Package 3: Mechanical, Electrical and Measurement Tools
    • Package 4: Power Supply, Accessories and Safety Equipment
    View all
  • Mechanical Parts212 products
    • Bearings
    • Brackets & Mounts
    • Couplers
    • Fasteners & Standoffs
    View all
  • Audio109 products
    • Amplifier Modules
    • Buzzers & Sirens
    • Speakers
    View all
  1. Home
  2. ›Guides
  3. ›3D Printing
  4. ›3D Printer Bed Levelling and First-Layer Fixes

Troubleshooting · Beginner · 4 min read

3D Printer Bed Levelling and First-Layer Fixes

By Geekobot Learning Team · Updated 24 Oct 2026

On this page
Short answerTramming, levelling and mesh: what is the difference?The paper method, step by stepHow to read your first layerAuto bed levelling probesFirst-layer settings that help adhesionStep by stepCommon mistakesFAQsParts and next steps
Short answer

Bed levelling sets the gap between nozzle and bed so the first layer is squashed just enough to stick. Heat the bed and nozzle, home the printer, then adjust each corner until a sheet of paper drags slightly under the nozzle. After that, fine-tune the Z offset while printing a test square: lines should be flat and touching, not round or transparent. Auto-levelling probes measure the bed but still need a correct Z offset.

Key specs at a glance

Paper gap
About 0.1 mm (ordinary printer paper)
Level when
Bed and nozzle at printing temperature
Z offset
Fine adjustment in 0.02 to 0.05 mm steps
Probe types
BLTouch / CR Touch (any bed), inductive (metal beds only), strain gauge or load cell (built-in)
Mesh
3x3 to 7x7 points; more points on warped beds
First layer
Usually 0.2 to 0.28 mm thick, printed slowly
01

Tramming, levelling and mesh: what is the difference?

Tramming (what most people call levelling) makes the bed parallel to the nozzle's path using the corner screws. Z offset sets how far the nozzle is from the bed at the trigger point. Mesh levelling measures many points and lets the firmware raise and lower the nozzle to follow small dips and bumps. You still need the first two: a mesh cannot fix a bed that is badly tilted or a Z offset that is wrong.

02

The paper method, step by step

  1. 1
    Clean the bed with isopropyl alcohol (IPA) or, for PEI sheets, warm water and dish soap.
  2. 2
    Heat the bed and nozzle to your usual printing temperatures; metal expands, and cold levelling is off by a few hundredths of a millimetre.
  3. 3
    Home all axes, then disable steppers (or use the printer's levelling menu to move to each corner).
  4. 4
    Slide a sheet of paper under the nozzle at one corner and turn the knob until the paper drags slightly but still moves.
  5. 5
    Repeat at all four corners, then the centre, and go round a second time; adjusting one corner moves the others a little.
  6. 6
    Print a single-layer test square and adjust the Z offset live (baby-stepping) until it looks right.
03

How to read your first layer

What you seeCauseFix
Round lines with gaps, peeling offNozzle too highLower Z offset by 0.02 to 0.05 mm
Transparent, rough, ridged surface; nozzle scrapesNozzle too lowRaise Z offset
Good in one corner, bad in anotherBed not trammed or warpedRe-tram; enable mesh levelling
Corners lift after a few layersWarping from coolingBrim, higher bed temperature, enclosure (ABS/ASA), less fan
Wide bottom edge on the partElephant's foot: first layer too squashed or bed too hotRaise Z slightly, lower bed temperature, use slicer compensation
Sticks too well to PEI (PETG)PETG bonds hard to smooth PEIUse textured PEI or a thin glue-stick layer
Round lines with gaps, peeling off
Cause:
Nozzle too high
Fix:
Lower Z offset by 0.02 to 0.05 mm
Transparent, rough, ridged surface; nozzle scrapes
Cause:
Nozzle too low
Fix:
Raise Z offset
Good in one corner, bad in another
Cause:
Bed not trammed or warped
Fix:
Re-tram; enable mesh levelling
Corners lift after a few layers
Cause:
Warping from cooling
Fix:
Brim, higher bed temperature, enclosure (ABS/ASA), less fan
Wide bottom edge on the part
Cause:
Elephant's foot: first layer too squashed or bed too hot
Fix:
Raise Z slightly, lower bed temperature, use slicer compensation
Sticks too well to PEI (PETG)
Cause:
PETG bonds hard to smooth PEI
Fix:
Use textured PEI or a thin glue-stick layer
04

Auto bed levelling probes

A BLTouch or CR Touch uses a small pin that touches the bed and works on glass, PEI or any surface. Inductive probes sense metal, so they need a steel or aluminium bed and do not work on glass. Many newer printers use a strain gauge or load cell in the hot end so the nozzle itself is the probe, which removes the probe-to-nozzle offset.

With a probe, the routine is: home, run the mesh (G29 in Marlin, BED_MESH_CALIBRATE in Klipper), save it (M500 in Marlin, SAVE_CONFIG in Klipper), and load it in the start G-code. Then set the Z offset once with the paper or test-square method.

05

First-layer settings that help adhesion

  • ✓Print the first layer at 20 to 30 mm/s and slightly hotter (5 °C) than the rest.
  • ✓Use 100% fan off for the first layer or two (PLA can go back to full fan after that).
  • ✓Bed temperature: PLA 55 to 65 °C, PETG 70 to 85 °C, ABS and ASA 95 to 110 °C (see the filament guide).
  • ✓Keep the bed clean: a fingerprint is enough to stop PLA sticking.
  • ✓Use a brim for tall, thin or sharp-cornered parts, and dry wet filament before blaming the bed.
06

Level a 3D printer bed with the paper method

You need: 3D printer, Filament for a test print · Tools: Sheet of printer paper, Isopropyl alcohol and lint-free cloth

Get the parts1 of 2 found in our store · ₹138

  • 3D printer3D Printer Heated Bed Power Controller Module₹138
  • Filament for a test printFind this part
  1. 1
    Clean the bedWipe the build surface with IPA, or wash a PEI sheet with warm soapy water.
  2. 2
    Heat upHeat bed and nozzle to normal printing temperatures.
  3. 3
    HomeHome all axes and move the nozzle to the first corner.
  4. 4
    Adjust cornersTurn each corner knob until the paper drags slightly under the nozzle; repeat for all corners twice.
  5. 5
    Test printPrint a one-layer square and adjust the Z offset until the lines are flat and just touching.
07

Common mistakes to avoid

  • !Levelling with a cold bed, then printing hot.
  • !Relying on a mesh to fix a bed that is badly tilted.
  • !Leaving fingerprints or oil on the bed.
  • !Forgetting to load the saved mesh in the start G-code.
  • !Turning the corner knobs while the probe-to-nozzle Z offset is wrong, and chasing the problem in circles.
08

Frequently asked questions

How tight should the paper be when levelling a 3D printer?

It should drag slightly as you slide it, like light friction, but not tear or stop. That gap is roughly 0.1 mm.

Do I need to level the bed before every print?

No. Check it after moving the printer, changing the nozzle or build plate, or if first layers start failing. Printers with auto levelling often re-probe at each start.

What is Z offset?

The distance between where the probe or endstop triggers and where the nozzle should be for the first layer. It is the fine adjustment that makes the first layer squish correctly.

Why is my first layer not sticking?

Usually the nozzle is too high, the bed is dirty, or the bed is too cool. Lower the Z offset slightly, clean the bed and check the temperatures for your filament.

Does BLTouch work on a glass bed?

Yes. It touches the surface physically, so it works on glass, PEI and other surfaces. Inductive probes need a metal bed.

Parts for this guide

  • Numakers 256x256mm Build Plate for Bambu Lab X1/P1/A1 Series
    ₹1,999View
  • Numakers IceGrip Build Plate for Bambu Lab A1 Mini
    ₹1,799View
  • Digital Vernier Caliper 150mm
    ₹629View
Shop 3D Printer SparesShop 3D Printers

Terms in this guide

FDMFused deposition modelling: the common 3D printing method that melts filament and lays it down layer by layer.Heated bedThe heated build plate of a 3D printer. It keeps the first layers warm so they stick and do not warp; PLA needs about 60 °C, ABS about 100 °C.CalibrationMeasuring a sensor against known conditions so its raw numbers can be converted into meaningful values, such as dry and wet readings for a soil sensor.

Projects that use it

Put this into practice: 1 step-by-step build in our project library uses parts from this guide.

Intermediate · 3 hoursAdd CR Touch auto bed levelling and a PEI sheet to an Ender-style printerView project
Browse all 1 project

Keep learning

Buying guideBeginner3D Printer NozzlesMost FDM printers ship with a 0.4 mm brass nozzle, which is right for PLA, PETG, ABS and TPU.4 min read · 3D PrintingComparisonBeginnerPLA vs PETG vs ABS vs TPUPLA, PETG, ABS, ASA, TPU and nylon compared: strength, heat resistance, print and bed temperatures, enclosure and drying needs, and which to choose.3 min read · 3D PrintingConcept explainerBeginnerResin 3D Printing BasicsA resin printer cures liquid photopolymer with 405 nm UV light, one thin layer at a time, using an LCD screen as a mask.4 min read · 3D Printing

Sources

  • Marlin firmware documentation: G29, M500, M851
  • Klipper documentation: bed mesh and probe calibration
  • Printer manufacturer levelling instructions (Prusa, Creality)

Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

On this page
Short answerTramming, levelling and mesh: what is the difference?The paper method, step by stepHow to read your first layerAuto bed levelling probesFirst-layer settings that help adhesionStep by stepCommon mistakesFAQsParts and next steps
Need a hand?Ask Geeko AI which part fits your project, or talk to the Geekobot team.Ask Geeko AIHelp & support

Parts for this guide1 item · ₹138

3D Printer Heated Bed Power Controller Module

Ask the Community

Ask a question