Comparison · Beginner · 3 min read
PLA vs PETG vs ABS vs TPU
Which 3D Printing Filament to Use
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
Use PLA for most prints: it is the easiest, cheapest and most accurate, but softens above about 55 °C. Use PETG for parts that need toughness, some flex and a little heat resistance, such as enclosures and brackets. Use ABS or ASA for heat and outdoor use (ASA resists UV), which need an enclosed printer. Use TPU for flexible parts. Keep filament dry, especially PETG, TPU and nylon.
Key specs at a glance
- PLA
- Nozzle 190 to 220 °C, bed 50 to 60 °C, no enclosure
- PETG
- Nozzle 230 to 250 °C, bed 70 to 85 °C, no enclosure, dry it
- ABS
- Nozzle 240 to 260 °C, bed 95 to 110 °C, enclosure needed
- ASA
- Like ABS, UV resistant for outdoor parts
- TPU (95A)
- Nozzle 220 to 240 °C, bed 40 to 60 °C, slow (20 to 30 mm/s), direct drive
- Nylon
- Nozzle 250 to 280 °C, bed 80 to 100 °C, very hygroscopic
- Diameter
- 1.75 mm is standard; 2.85 mm on some printers
Filament comparison
| PLA | PETG | ABS / ASA | TPU | Nylon | |
|---|---|---|---|---|---|
| Ease of printing | Easiest | Easy (stringing) | Hard (warping, fumes) | Medium (slow) | Hard (moisture) |
| Strength | Stiff, brittle | Tough, slight flex | Tough, impact resistant | Flexible, rubber-like | Very tough, wear resistant |
| Heat resistance | About 55 °C | About 75 °C | About 95 to 100 °C | About 70 °C | About 100 °C+ |
| Outdoor / UV | Poor | OK | ASA good, ABS fades | OK | Absorbs water |
| Smell / fumes | Low | Low | Styrene fumes, ventilate | Low | Low |
| Typical uses | Prototypes, models, toys, jigs | Enclosures, brackets, mechanical parts | Car parts, outdoor housings, Lego-like parts | Phone cases, gaskets, wheels, straps | Gears, hinges, functional parts |
- Ease of printing
- PLA:
- Easiest
- PETG:
- Easy (stringing)
- ABS / ASA:
- Hard (warping, fumes)
- TPU:
- Medium (slow)
- Nylon:
- Hard (moisture)
- Strength
- PLA:
- Stiff, brittle
- PETG:
- Tough, slight flex
- ABS / ASA:
- Tough, impact resistant
- TPU:
- Flexible, rubber-like
- Nylon:
- Very tough, wear resistant
- Heat resistance
- PLA:
- About 55 °C
- PETG:
- About 75 °C
- ABS / ASA:
- About 95 to 100 °C
- TPU:
- About 70 °C
- Nylon:
- About 100 °C+
- Outdoor / UV
- PLA:
- Poor
- PETG:
- OK
- ABS / ASA:
- ASA good, ABS fades
- TPU:
- OK
- Nylon:
- Absorbs water
- Smell / fumes
- PLA:
- Low
- PETG:
- Low
- ABS / ASA:
- Styrene fumes, ventilate
- TPU:
- Low
- Nylon:
- Low
- Typical uses
- PLA:
- Prototypes, models, toys, jigs
- PETG:
- Enclosures, brackets, mechanical parts
- ABS / ASA:
- Car parts, outdoor housings, Lego-like parts
- TPU:
- Phone cases, gaskets, wheels, straps
- Nylon:
- Gears, hinges, functional parts
Which filament for which project?
PLA, or PETG if a regulator or Pi inside gets warm.
PETG for toughness; PLA+ if you want easier printing.
ASA.
TPU 95A.
nylon or PETG with a drop of lubricant.
none are certified once printed; use food-safe inserts.
Settings that matter most
print a temperature tower for each new spool; brands vary by 10 °C.
PLA sticks to PEI or glue stick; PETG sticks too well to bare PEI (use glue stick as a release layer); ABS needs a heated enclosure and brim.
PLA 100% fan; PETG 30 to 50%; ABS off or minimal.
PLA fast; TPU 20 to 30 mm/s on a direct-drive extruder; Bowden extruders struggle with soft TPU.
PETG and TPU string; lower retraction speed and temperature a little.
Keep it dry
Filament absorbs moisture from the air, which causes popping, stringing, weak layers and rough surfaces. PETG, TPU and nylon are worst; PLA suffers after weeks in humid air, which matters in most of India during the monsoon. Store spools in sealed boxes with desiccant and dry wet filament in a filament dryer or an oven at 45 to 55 °C (PLA) or 60 to 70 °C (PETG) for 4 to 6 hours.
What to look for when buying
Diameter tolerance (±0.02 mm is good), spool weight (1 kg net), a stated print temperature range, and vacuum packing with desiccant. Cheap filament with poor diameter control jams and under-extrudes. Silk and matte PLA print like PLA with slightly different temperatures; PLA+ or Tough PLA adds impact strength; carbon-fibre blends need a hardened nozzle.
Try it: 3D print cost calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Printing PLA parts for anything that gets hot and watching them warp.
- Printing PETG on bare PEI and tearing the sheet when removing the part.
- Trying TPU at normal speeds on a Bowden printer.
- Leaving spools open on the printer in humid weather.
- Printing ABS in a closed room without ventilation.
Frequently asked questions
Which filament is best for beginners?
PLA. It prints at low temperature without an enclosure, sticks well to most beds and gives clean detail. PETG is the natural second filament.
Is PETG stronger than PLA?
PETG is tougher (absorbs impact and bends before breaking) and handles more heat, while PLA is stiffer and holds finer detail. For functional parts, PETG usually wins.
Does ABS need an enclosure?
Yes, for anything beyond small parts. ABS shrinks as it cools, so without a warm, draught-free enclosure it warps and cracks between layers. ASA behaves the same but resists sunlight.
What temperature should I print PLA at?
190 to 220 °C nozzle and 50 to 60 °C bed are typical. Print a temperature tower for your spool and printer.
How do I know if my filament is wet?
Popping or hissing at the nozzle, excessive stringing, rough or bubbly surfaces and weak layer bonding. Dry it for a few hours and the print quality returns.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
- eSUN, Polymaker and Prusament filament technical datasheets
- Prusa Knowledge Base: material guide
- Bambu Lab filament guide
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




