Concept explainer · Beginner · 4 min read
Resin 3D Printing Basics
How MSLA Works and How to Stay Safe
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
A resin printer cures liquid photopolymer with 405 nm UV light, one thin layer at a time, using an LCD screen as a mask. It gives far finer detail than filament printing, which makes it ideal for miniatures, jewellery models and dental work. The trade-offs are messier post-processing (wash in alcohol or water, then UV cure) and real safety rules: uncured resin irritates and sensitises skin, so always wear nitrile gloves and ventilate.
Key specs at a glance
- Light
- 405 nm UV through a monochrome LCD mask
- Layer height
- 0.025 to 0.1 mm (0.05 mm typical)
- XY detail
- Set by LCD pixel size, about 20 to 50 µm
- Normal exposure
- About 1.5 to 3 s per layer on mono LCD printers
- Ideal temperature
- Around 25 °C; resin gets thick and fails when cold
- Post-process
- Wash (IPA or water) then UV cure
How an MSLA printer works
The build plate dips into a vat of resin with a clear film (FEP or similar) at the bottom. A UV LED array shines up through an LCD screen that shows each layer's shape; the exposed resin hardens against the plate. The plate lifts, peels the layer off the film, drops back down and the next layer is exposed. Because a whole layer cures at once, print time depends on height, not on how many parts you fit on the plate.
Resin vs filament (FDM)
| Resin (MSLA) | Filament (FDM) | |
|---|---|---|
| Detail | Excellent, near-invisible layers | Good; visible layer lines |
| Part size | Small to medium | Small to large |
| Strength | Brittle unless you buy tough or ABS-like resin | Good, especially PETG and nylon |
| Post-processing | Wash, cure, remove supports | Remove supports |
| Mess and safety | Gloves, ventilation, waste handling | Fumes from ABS/ASA; otherwise easy |
| Best for | Miniatures, jewellery masters, dental, fine prototypes | Functional parts, enclosures, brackets |
- Detail
- Resin (MSLA):
- Excellent, near-invisible layers
- Filament (FDM):
- Good; visible layer lines
- Part size
- Resin (MSLA):
- Small to medium
- Filament (FDM):
- Small to large
- Strength
- Resin (MSLA):
- Brittle unless you buy tough or ABS-like resin
- Filament (FDM):
- Good, especially PETG and nylon
- Post-processing
- Resin (MSLA):
- Wash, cure, remove supports
- Filament (FDM):
- Remove supports
- Mess and safety
- Resin (MSLA):
- Gloves, ventilation, waste handling
- Filament (FDM):
- Fumes from ABS/ASA; otherwise easy
- Best for
- Resin (MSLA):
- Miniatures, jewellery masters, dental, fine prototypes
- Filament (FDM):
- Functional parts, enclosures, brackets
Supports, hollowing and exposure
Resin parts hang upside down from the plate, so overhangs need supports, and parts are usually tilted 30 to 45° to reduce peel force on each layer. Large solid parts waste resin and can crack; hollow them with 2 to 3 mm walls and add at least two drain holes so trapped resin escapes, otherwise suction cups form and uncured resin inside can split the part later.
Exposure is the main setting. Print a calibration test (such as a resin exposure matrix) whenever you change resin brand or colour. Underexposure gives soft, failed supports; overexposure bloats fine details.
Washing and curing
- 1Let the part drip over the vat for a minute.
- 2Wash in isopropyl alcohol (90% or stronger) for standard resin, or in water for water-washable resin. Two baths (dirty then clean) or a wash station works best; 3 to 5 minutes is enough.
- 3Let it dry fully; curing a wet part leaves a white film.
- 4Cure under 405 nm UV (a curing station or sunlight) for a few minutes. Over-curing makes parts brittle.
- 5Remove supports after a short cure, or before curing for cleaner nubs, then sand while wet with a mask on.
Safety rules you should not skip
- Wear nitrile gloves whenever you touch resin or uncured parts. Latex is not resistant enough. Resin sensitisation is cumulative: people who get it on their skin repeatedly can develop a lifelong allergy.
- Wear eye protection when pouring or cleaning.
- Ventilate. Resin and IPA give off vapours; print in a room with airflow, not a bedroom.
- Never pour resin or dirty IPA down a drain. Leave used IPA in sunlight in a clear container until the resin settles and cures, then filter it and dispose of the cured solids with household waste. Cure leftover liquid resin before throwing it away.
- Keep resin away from children, pets and food areas, and store it in its opaque bottle away from sunlight.
Common mistakes to avoid
- Handling resin without gloves because it is 'only a small drip'.
- Printing in a cold room, which causes failed prints and layer separation.
- Leaving parts solid or without drain holes.
- Curing parts while they are still wet with IPA.
- Pouring dirty IPA down the sink.
Frequently asked questions
Is resin 3D printing safe at home?
It can be, with precautions: nitrile gloves, eye protection, good ventilation, a dedicated work area and correct disposal. Uncured resin is a skin irritant and sensitiser, so avoid all skin contact.
What is water-washable resin?
Resin you can clean with water instead of IPA. It is easier to handle, but the waste water still contains resin and must be cured and filtered, not poured away.
Should I buy a resin or FDM printer first?
For functional parts, brackets and enclosures, start with FDM. Choose resin if your main use is miniatures, jewellery or very fine detail.
How long do you cure resin prints?
Usually 2 to 10 minutes in a curing station, depending on size and resin. Follow the resin maker's guidance; over-curing makes parts brittle.
Why do resin prints fail to stick to the plate?
Common causes are too few or too short bottom-layer exposures, a cold room, an unlevelled plate, or a damaged FEP film.
Parts for this guide
Terms in this guide
Keep learning
Sources
- Resin manufacturer safety data sheets (SDS)
- Formlabs and printer maker post-processing guidance
- UniFormation and Anycubic user manuals
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




