Component guide · Intermediate · 3 min read
MAX31856 and MCP9600 Universal Thermocouple Amplifiers (K, J, T, N, S, E, B, R)

Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The MAX31856 and MCP9600 read almost any thermocouple type, not only K-type like the MAX6675 and MAX31855. The MAX31856 talks SPI and supports K, J, N, R, S, T, E and B types with 19-bit resolution and fault detection. The MCP9600 talks I2C, supports eight types and has four programmable temperature alerts. Both measure their own cold junction.
Key specs at a glance
- Thermocouple types
- B, E, J, K, N, R, S, T (both)
- Interface
- SPI (MAX31856), I2C 0x60 to 0x67 (MCP9600)
- Resolution
- 0.0078 degrees C (MAX31856), 0.0625 degrees C (MCP9600)
- Accuracy
- About plus or minus 0.7 degrees C (MAX31856), 1.5 degrees C (MCP9600) plus probe error
- Supply
- 3.3 to 5 V on the breakouts
- Extras
- Open-probe fault detection, alert outputs (MCP9600)
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
What the MAX31856 and MCP9600 thermocouple amplifiers is
A thermocouple only measures the difference between its tip and the screw terminals. These chips measure the terminal (cold junction) temperature and add it back, so keep the board away from heat sources.
Use thermocouple wire or matching extension cable all the way to the board; ordinary copper wire in between adds errors.
MAX31856 and MCP9600 thermocouple amplifiers pinout
The pins on the MAX31856 and MCP9600 thermocouple amplifiers and what each one does.
| Pin | Function |
|---|---|
| T+ / T- | Thermocouple (yellow is + on K-type, red is -) |
| VIN, GND | Power |
| SCK, SDO, SDI, CS | SPI (MAX31856) |
| SDA, SCL | I2C (MCP9600) |
| DRDY / FAULT / ALERT | Optional status pins |
- T+ / T-
- Thermocouple (yellow is + on K-type, red is -)
- VIN, GND
- Power
- SCK, SDO, SDI, CS
- SPI (MAX31856)
- SDA, SCL
- I2C (MCP9600)
- DRDY / FAULT / ALERT
- Optional status pins
Wiring the MAX31856 and MCP9600 thermocouple amplifiers
Pimoroni and CJMCU MCP9600 boards default to address 0x66 or 0x67. Check with an I2C scanner.
| MAX31856 and MCP9600 thermocouple amplifiers pin | Arduino Uno | ESP32 |
|---|---|---|
| VIN | 5 V | 3.3 V |
| GND | GND | GND |
| MAX31856 SCK / SDO / SDI / CS | D13 / D12 / D11 / D10 | GPIO 18 / 19 / 23 / 5 |
| MCP9600 SDA / SCL | A4 / A5 | GPIO 21 / 22 |
- VIN
- Arduino Uno:
- 5 V
- ESP32:
- 3.3 V
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- MAX31856 SCK / SDO / SDI / CS
- Arduino Uno:
- D13 / D12 / D11 / D10
- ESP32:
- GPIO 18 / 19 / 23 / 5
- MCP9600 SDA / SCL
- Arduino Uno:
- A4 / A5
- ESP32:
- GPIO 21 / 22
Example code
For the MCP9600 use the Adafruit MCP9600 library and setThermocoupleType(MCP9600_TYPE_K).
#include <Adafruit_MAX31856.h>
Adafruit_MAX31856 tc(10); // CS pin, hardware SPI
void setup() {
Serial.begin(115200);
tc.begin();
tc.setThermocoupleType(MAX31856_TCTYPE_K); // change for J, T, N...
tc.setConversionMode(MAX31856_CONTINUOUS);
}
void loop() {
Serial.print("Tip "); Serial.print(tc.readThermocoupleTemperature(), 2);
Serial.print(" C Cold junction "); Serial.println(tc.readCJTemperature(), 2);
if (tc.readFault()) Serial.println("Fault: check the probe");
delay(1000);
}Setup and tuning
both chips default to K-type; change it for other probes.
a probe touching a grounded metal part can upset readings; prefer isolated tips.
keep the probe cable away from mains and motor wires.
What you need
Shop this list6 of 7 found in our store · ₹9,513
Adafruit Universal Thermocouple Amplifier MAX31856 Breakout – SPI Interface: the part this guide coversAdafruit Universal Thermocouple Amplifier MAX31856 Breakout – SPI Interface₹2,929
Pimoroni MCP9600 Thermocouple Amplifier Breakout – I2C Interface, 3.3V/5V: another version this guide coversPimoroni MCP9600 Thermocouple Amplifier Breakout – I2C Interface, 3.3V/5V₹2,476
CJMCU-96 MCP9600 Thermocouple Converter Module – I2C Interface, 8 Thermocouple Types: another version this guide coversCJMCU-96 MCP9600 Thermocouple Converter Module – I2C Interface, 8 Thermocouple Types₹3,479- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
K-type thermocouple probe: a probe to plug inK-Type Thermocouple Probe₹101
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Alternatives and when to choose them
- MAX6675 module: K-type only, 0.25 degrees C steps, lowest cost.
- MAX31855 module: K-type, wider range.
- K-type thermocouple probes: choosing the probe.
Common mistakes to avoid
- Leaving the type set to K with a J-type probe.
- Copper wire between probe and board.
- Mounting the board next to the heater.
Frequently asked questions
Which types are supported?
B, E, J, K, N, R, S and T on both.
SPI or I2C?
MAX31856 is SPI, MCP9600 is I2C.
How many on one bus?
Up to eight MCP9600 by address; one CS pin each for MAX31856.
Does polarity matter?
Yes; reversed leads read backwards as it heats.
Is it better than MAX6675?
Yes for accuracy, resolution and probe types.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

