Component guide · Beginner · 3 min read
MAX6675 thermocouple module

Pinout, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The MAX6675 module reads a K-type thermocouple and outputs temperature from 0 to 1024 °C in 0.25 °C steps over a simple 3-wire SPI interface. It handles cold-junction compensation for you. Use it for ovens, reflow plates, kilns and 3D printer hot ends where normal sensors would melt.
Key specs at a glance
- Thermocouple
- K-type only
- Range
- 0 to 1024 °C
- Resolution
- 0.25 °C (12-bit)
- Accuracy
- About ±2 to ±3 °C
- Interface
- SPI, read only (SO, SCK, CS)
- Supply
- 3.0 to 5.5 V
- Conversion time
- About 220 ms
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
What the MAX6675 thermocouple module is
A thermocouple is two different metals joined at the tip; heating the joint makes a tiny voltage of about 41 µV per °C for K-type. The MAX6675 amplifies that voltage, measures the temperature of its own terminals (cold junction) to correct the reading, and outputs a digital value.
Because the probe has no electronics, it survives temperatures far beyond any chip-based sensor.
MAX6675 thermocouple module pinout
The pins on the MAX6675 thermocouple module and what each one does.
| Pin | Function |
|---|---|
| VCC | 3.0 to 5.5 V |
| GND | Ground |
| SCK | SPI clock |
| CS | Chip select |
| SO | Serial data out |
| + / − terminals | Thermocouple wires (K-type, observe polarity) |
- VCC
- 3.0 to 5.5 V
- GND
- Ground
- SCK
- SPI clock
- CS
- Chip select
- SO
- Serial data out
- + / − terminals
- Thermocouple wires (K-type, observe polarity)
Wiring the MAX6675 thermocouple module
Any digital pins work because the library uses software SPI. If readings rise when the probe cools, the thermocouple wires are reversed.
| MAX6675 thermocouple module pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5V | 3V3 |
| GND | GND | GND |
| SCK | D6 | GPIO 18 |
| CS | D5 | GPIO 5 |
| SO | D4 | GPIO 19 |
- VCC
- Arduino Uno:
- 5V
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SCK
- Arduino Uno:
- D6
- ESP32:
- GPIO 18
- CS
- Arduino Uno:
- D5
- ESP32:
- GPIO 5
- SO
- Arduino Uno:
- D4
- ESP32:
- GPIO 19
Example code
Install the MAX6675 library by Adafruit. Reading faster than every 220 ms returns the same value.
#include <max6675.h>
const int SCK_PIN = 6, CS_PIN = 5, SO_PIN = 4;
MAX6675 tc(SCK_PIN, CS_PIN, SO_PIN);
void setup() {
Serial.begin(9600);
delay(500); // let the chip settle
}
void loop() {
float c = tc.readCelsius();
if (isnan(c)) Serial.println("Thermocouple not connected");
else { Serial.print(c); Serial.println(" C"); }
delay(300); // needs about 220 ms per conversion
}Setup and tuning
on most K-type wire the red lead is negative; check the probe label.
some metal probes connect the tip to their sheath; touching a grounded metal surface can cause errors.
the MAX6675 cannot read under 0 °C; use the MAX31855 for that.
combine it with an SSR and PID library for a reflow plate or kiln controller.
What you need
Shop this list4 of 5 found in our store · ₹798
MAX6675 module with K-type thermocouple (50 cm): module and probe togetherMAX6675 Module + K-Type Thermocouple Sensor w/ 50cm Cable₹279Closest match, check the specs
MAX6675 thermocouple module (K-type, SPI): module onlyMAX6675 Thermocouple Sensor Module – K-Type, SPI Interface₹239
K-type thermocouple probe: spare or longer probeK-Type Thermocouple Probe₹101- Uno R3 development board: the controller used in the wiring tableFind this part
16x2 LCD with I2C: to show readings on a character display16×2 LCD with I2C (RG1602A)₹179Closest match, check the specs
Alternatives and when to choose them
Try it: Temperature converter calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Reversing the thermocouple wires.
- Using a J-type or T-type probe; it is K-type only.
- Reading faster than every 220 ms.
- Extending the probe with copper wire instead of K-type extension wire.
Frequently asked questions
What is the maximum temperature?
1024 °C for the chip, but the probe sets the real limit; many cheap probes are rated 400 to 600 °C.
Can it measure below 0 °C?
No. Use a MAX31855 for negative temperatures.
Does it work with ESP32?
Yes, at 3.3 V with any three GPIO pins.
Why does it read NAN?
The thermocouple is not connected or the wires are broken.
How accurate is it?
Around ±2 to ±3 °C, fine for ovens and kilns but not for lab work.
Can I use several on one board?
Yes. Share SCK and SO and give each module its own CS pin.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 21 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

