LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA clay oven needs to be properly hot before the dough goes in. Push the thermocouple through a small hole in the oven wall and the LCD shows the air temperature. At 300 °C the green light comes on and a chirp tells you to start cooking.
Keep the board and LCD away from the heat, and use gloves and tongs when cooking.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Reads a K-type thermocouple probe up to 1,000 °C through an amplifier chip, which is the way to measure ovens, kilns, soldering irons and engines.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
pizza_oven_ready_alert.inoVerify & upload in Electrolark// Pizza and tandoor oven ready alert
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "pizza-oven-ready-alert"
#include <max6675.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t TC_SCK = 2;
const uint8_t TC_CS = 3;
const uint8_t TC_SO = 4;
const uint8_t BUZZER_PIN = 5;
const uint8_t LED_GREEN = 6;
MAX6675 thermocouple(TC_SCK, TC_CS, TC_SO);
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float probeC = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 300; // 300 C and above is a good heat for pizza and naan; change it for your recipe
const float HYSTERESIS = 20; // gap that stops rapid on/off switching
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Probe "));
lcd.print(probeC, 0);
lcd.print(F(" C"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(statusText);
lcd.print(F(" "));
}
void evaluate() {
if (!(!isnan(probeC))) { statusText = "Sensor error"; return; }
if (!alertOn && probeC > ALERT_LEVEL) alertOn = true;
else if (alertOn && probeC < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "READY TO COOK" : "Heating up";
}
void setup() {
Serial.begin(115200);
lcd.init();
lcd.backlight();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_GREEN, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
probeC = thermocouple.readCelsius();
evaluate();
Serial.print(F("Probe="));
Serial.print(probeC, 0);
Serial.print(F("C"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setGreenLed(!alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The thermocouple is not connected or its plus and minus wires are swapped. Check the screw terminals.
The module also senses its own temperature at the cold junction. Keep it away from the heat you are measuring.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Nano CH340 Development Board (Soldered), MAX6675 Module with K-Type Thermocouple Probe, 50 cm Cable, LCD1602 16x2 Character LCD (blue, with I2C adapter), Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 10 steps.
No. This page has the complete, tested code (pizza_oven_ready_alert.ino). Install these libraries first: MAX6675 library and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹715 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Character displays and I²C backpacks; Current-limiting resistors for LEDs; Thermocouples and cold-junction compensation.
Keep the board and LCD away from the heat, and use gloves and tongs when cooking.
Ideas that reuse this build: Wi-Fi oven monitor and Pottery kiln monitor. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Probe=180C, status=Heating up Probe=180C, status=Heating up
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.