LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsCheap irons are often far from the temperature printed on the dial. Touch the thermocouple tip to the iron tip with a drop of solder and the OLED shows the number: about 320 to 350 °C suits most work. Use it to set your station once and trust it.
The iron is hot. Hold the probe with pliers, touch only briefly and keep the board away from the iron.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Reads a K-type thermocouple probe up to 1,000 °C through an amplifier chip, which is the way to measure ovens, kilns, soldering irons and engines.
Follow the colours: red is power, dark grey is ground, blue is a signal.
soldering_iron_tip_checker.inoVerify & upload in Electrolark// Soldering iron tip temperature checker
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "soldering-iron-tip-checker"
#include <max6675.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t TC_SCK = 2;
const uint8_t TC_CS = 3;
const uint8_t TC_SO = 4;
MAX6675 thermocouple(TC_SCK, TC_CS, TC_SO);
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float probeC = 0;
const unsigned long READ_EVERY_MS = 500;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Iron tip"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 16);
oled.print(F("Probe"));
oled.setTextSize(2);
oled.setCursor(0, 28);
oled.print(probeC, 0);
oled.print(F(" C"));
oled.setTextSize(1);
oled.setCursor(0, 56);
oled.print(statusText);
oled.display();
}
void setup() {
Serial.begin(115200);
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
probeC = thermocouple.readCelsius();
statusText = (!isnan(probeC)) ? "OK" : "Sensor error";
Serial.print(F("Probe="));
Serial.print(probeC, 0);
Serial.print(F("C"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The thermocouple is not connected or its plus and minus wires are swapped. Check the screw terminals.
The module also senses its own temperature at the cold junction. Keep it away from the heat you are measuring.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), MAX6675 Module with K-Type Thermocouple Probe, 50 cm Cable, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (soldering_iron_tip_checker.ino). Install these libraries first: MAX6675 library, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹698 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Drawing text on an I²C display; Thermocouples and cold-junction compensation.
The iron is hot. Hold the probe with pliers, touch only briefly and keep the board away from the iron.
Ideas that reuse this build: Soldering iron left-on reminder and Solder station fume and heat monitor. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Probe=180C Probe=180C Probe=180C Probe=180C Probe=180C
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.