LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe infrared sensor points at the soldering iron tip from a safe distance, and the air sensor above the bench reads the fumes. Together the OLED shows whether the iron has warmed up to a good soldering temperature and whether it is time to switch on the fan.
Mount the sensor on a bracket at least 10 cm from the iron tip, away from heat and flux splatter.
This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed.
Not a medical device. Readings are for learning and must not be used for diagnosis.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Infrared thermometer: measures the temperature of whatever it points at without touching it (field of view about 90°).
Heated sensor that responds to ammonia, CO₂, alcohol, smoke and benzene.
Follow the colours: red is power, dark grey is ground, blue is a signal.
solder_station_fume_and_heat_monitor.inoVerify & upload in Electrolark// Soldering bench fume and heat monitor
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "solder-station-fume-and-heat-monitor"
#include <Wire.h>
#include <Adafruit_MLX90614.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t AIR_PIN = A0;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
Adafruit_MLX90614 mlx;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float objC = 0;
float ambC = 0;
int airPct = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Solder bench"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 14);
oled.print(F("Object: "));
oled.print(objC, 1);
oled.print(F(" C"));
oled.setCursor(0, 24);
oled.print(F("Air: "));
oled.print(airPct);
oled.print(F("%"));
oled.display();
}
void setup() {
Serial.begin(115200);
if (!mlx.begin()) Serial.println(F("MLX90614 not found"));
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
objC = mlx.readObjectTempC();
ambC = mlx.readAmbientTempC();
airPct = (int)(analogRead(AIR_PIN) * 100L / ADC_MAX);
Serial.print(F("Object="));
Serial.print(objC, 1);
Serial.print(F("C"));
Serial.print(F(", Air="));
Serial.print(airPct);
Serial.print(F("%"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
You are too far away, so the sensor sees mostly background. Move closer.
Normal: the heater needs a few minutes to settle. Wait before calibrating the threshold.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), MLX90614 IR Non-Contact Temperature Sensor Module, Winsen MQ135 Air Quality Gas Sensor, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (solder_station_fume_and_heat_monitor.ino). Install these libraries first: Adafruit MLX90614 Library, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,357 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Analog sensors, ADCs and warm-up drift; Contactless infrared temperature measurement; Drawing text on an I²C display.
Mount the sensor on a bracket at least 10 cm from the iron tip, away from heat and flux splatter. This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed. Not a medical device. Readings are for learning and must not be used for diagnosis.
Ideas that reuse this build: Workshop dust and fumes air alarm and Hot plate IR temperature display. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Object=34.9C, Air=30% Object=35.0C, Air=29%
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.