Component guide · Beginner · 3 min read
MAX4466 Microphone Amplifier

Pinout, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The MAX4466 module is an electret microphone with a low-noise op-amp. A small trim pot sets the gain from about 25 to 125 times, and the output is an audio waveform centred at half the supply voltage. Read it on an analog pin to measure sound level, detect claps or drive a VU meter. Use 3.3 V for the cleanest signal.
Key specs at a glance
- Microphone
- Electret capsule, 20 Hz to 20 kHz
- Amplifier
- MAX4466 low-noise op-amp
- Gain
- About 25x to 125x, set by a trim pot
- Supply
- 2.4 to 5.5 V
- Output
- Analog audio, centred at VCC/2, up to VCC peak to peak
- Gain control
- Fixed by the pot (no automatic gain)
What the MAX4466 microphone module is
Unlike the simple sound sensors with only a digital threshold output, the MAX4466 gives the real audio waveform. That makes it good for measuring loudness, for simple frequency analysis (FFT) and for sound-reactive LEDs.
The gain is fixed by the pot, so loud sounds clip and quiet ones are small. If your sound levels vary a lot, the MAX9814 with automatic gain control is easier.
MAX4466 microphone module pinout
The pins on the MAX4466 microphone module and what each one does.
| Pin | Function |
|---|---|
| VCC | Supply, 2.4 to 5.5 V |
| GND | Ground |
| OUT | Analog audio output, idles at VCC/2 |
- VCC
- Supply, 2.4 to 5.5 V
- GND
- Ground
- OUT
- Analog audio output, idles at VCC/2
Wiring the MAX4466 microphone module
On an Uno, connecting the module to 3.3 V and the 3.3 V pin also to AREF (with analogReference(EXTERNAL)) gives better resolution. The 5 V USB rail is noisy and adds hiss.
| MAX4466 microphone module pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 3.3V (quieter than 5V) | 3V3 |
| GND | GND | GND |
| OUT | A0 | GPIO 34 |
- VCC
- Arduino Uno:
- 3.3V (quieter than 5V)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- OUT
- Arduino Uno:
- A0
- ESP32:
- GPIO 34
Example code
Peak-to-peak gives a loudness value, not calibrated decibels. For sound-reactive LEDs, map it to brightness for WS2812B LEDs.
const int MIC = A0;
void setup() { Serial.begin(115200); }
void loop() {
unsigned long start = millis();
int lo = 1023, hi = 0;
while (millis() - start < 50) { // 50 ms window = 20 Hz and up
int v = analogRead(MIC);
if (v < lo) lo = v;
if (v > hi) hi = v;
}
int pp = hi - lo; // peak to peak
float volts = pp * 3.3 / 1023.0;
Serial.println(volts, 3); // view on the Serial Plotter
}Setup and tuning
start in the middle, then turn it down if loud sounds hit the top or bottom of the plotter.
3.3 V or a battery gives less hiss than the USB 5 V rail.
keep the OUT wire short and away from motor or LED wires.
for FFT, sample at a steady rate, at least twice the highest frequency you want.
What you need
Shop this list4 of 5 found in our store · ₹829
MAX4466 Electret Microphone Amplifier, Adjustable Gain: the part this guide coversMAX4466 Electret Microphone Amplifier, Adjustable Gain₹94- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
WS2812B addressable LED strip: for a sound-reactive lightWS2812B Addressable RGB LED Strip (30 LEDs/m)₹297Closest match, check the specs
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- MAX9814 microphone with AGC: automatic gain, so it copes with quiet and loud rooms.
- INMP441 I2S microphone: digital audio for ESP32 recording and voice projects.
- Sound sensor modules: simple clap switches with a digital threshold output.
Common mistakes to avoid
- Setting the gain to maximum so normal speech clips.
- Using analogRead once and expecting a loudness value; you need the peak-to-peak over a window.
- Powering it from noisy USB 5 V, which adds hiss.
- Expecting calibrated decibel readings without calibration against a sound meter.
Frequently asked questions
What is the MAX4466 output voltage?
It idles at half the supply (about 1.65 V on 3.3 V) and swings up and down with sound.
Can it record audio?
On an ESP32 it can capture low-quality audio, but an I2S microphone such as the INMP441 is far better.
MAX4466 or MAX9814?
MAX4466 if you want to set the gain yourself; MAX9814 if sound levels vary and you want automatic gain.
Can it measure decibels?
Only roughly, after calibrating against a real sound level meter.
Why is my signal noisy?
Usually the power supply. Use 3.3 V, short wires and keep it away from motors.
Parts for this guide
Keep learning
Sources
- MAX4466 low-cost micropower op-amp datasheet (Maxim Integrated)
- Adafruit electret microphone amplifier MAX4466 guide
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


