Component guide · Beginner · 3 min read
MAX9814 Microphone with AGC

Pinout, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The MAX9814 module is an electret microphone with an amplifier that has automatic gain control (AGC). It turns quiet sounds up and loud sounds down, so the output stays in range without clipping. The GAIN pin picks 40, 50 or 60 dB, and the AR pin sets how fast the AGC reacts. Read the analog output, centred at about 1.25 V, on any ADC pin.
Key specs at a glance
- Microphone
- Electret capsule
- Gain
- 40, 50 or 60 dB, chosen by the GAIN pin
- AGC
- Automatic gain control, about 20 dB range
- Supply
- 2.7 to 5.5 V
- Output
- Analog, about 2 V peak to peak on a 1.25 V bias
- AR ratio
- 1:500, 1:2000 or 1:4000, chosen by the AR pin
What the MAX9814 microphone module is
The AGC watches the output and lowers the gain when sounds get loud, then raises it again slowly. This keeps speech and music in a usable range in both quiet and noisy rooms, which is ideal for voice-activated projects and sound-reactive lights.
The trade-off is that the output level no longer tells you the true loudness, so for sound level measurement the fixed-gain MAX4466 is better.
MAX9814 microphone module pinout
The pins on the MAX9814 microphone module and what each one does.
| Pin | Function |
|---|---|
| VDD | Supply, 2.7 to 5.5 V |
| GND | Ground |
| OUT | Analog audio output, biased at about 1.25 V |
| GAIN | Unconnected = 60 dB, to GND = 50 dB, to VDD = 40 dB |
| AR | Attack/release: unconnected = 1:4000, GND = 1:2000, VDD = 1:500 |
- VDD
- Supply, 2.7 to 5.5 V
- GND
- Ground
- OUT
- Analog audio output, biased at about 1.25 V
- GAIN
- Unconnected = 60 dB, to GND = 50 dB, to VDD = 40 dB
- AR
- Attack/release: unconnected = 1:4000, GND = 1:2000, VDD = 1:500
Wiring the MAX9814 microphone module
Start with GAIN open (60 dB) for speech across a room. If a loud source is close, tie GAIN to GND (50 dB) or VDD (40 dB).
| MAX9814 microphone module pin | Arduino Uno | ESP32 |
|---|---|---|
| VDD | 3.3V | 3V3 |
| GND | GND | GND |
| OUT | A0 | GPIO 34 |
| GAIN | Leave open (60 dB) or to GND/VDD | Leave open or to GND/3V3 |
| AR | Leave open | Leave open |
- VDD
- Arduino Uno:
- 3.3V
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- OUT
- Arduino Uno:
- A0
- ESP32:
- GPIO 34
- GAIN
- Arduino Uno:
- Leave open (60 dB) or to GND/VDD
- ESP32:
- Leave open or to GND/3V3
- AR
- Arduino Uno:
- Leave open
- ESP32:
- Leave open
Example code
Tune the 600 in map() to the biggest peak-to-peak value you see in your room.
const int MIC = A0;
void setup() { Serial.begin(115200); }
void loop() {
unsigned long start = millis();
int lo = 1023, hi = 0;
while (millis() - start < 50) {
int v = analogRead(MIC);
lo = min(lo, v);
hi = max(hi, v);
}
int level = map(hi - lo, 0, 600, 0, 10); // 0 to 10 bars
for (int i = 0; i < level; i++) Serial.print('#');
Serial.println();
}Setup and tuning
60 dB for distant speech, 40 dB for loud music near the mic.
leave it open for smooth music levels; tie it to VDD for faster reaction to claps.
use 3.3 V or a battery; USB 5 V adds noise.
use an ADC1 pin (GPIO 32 to 39) so Wi-Fi does not interfere.
What you need
Shop this list4 of 5 found in our store · ₹933
MAX9814 Microphone Amplifier Module with AGC: the part this guide coversMAX9814 Microphone Amplifier Module with AGC₹198- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
WS2812B addressable LED strip: for a sound-reactive lightWS2812B Addressable RGB LED Strip (30 LEDs/m)₹297Closest match, check the specs
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- MAX4466 microphone amplifier: fixed gain set by a pot, better for loudness readings.
- INMP441 I2S microphone: digital audio, the best choice for ESP32 voice recording.
- Sound sensor modules: basic clap and knock detection.
Common mistakes to avoid
- Using it to measure loudness: the AGC hides the true sound level.
- Leaving GAIN at 60 dB for loud music right next to the mic.
- Reading single samples instead of peak to peak over a short window.
- Reading it on an ESP32 ADC2 pin while Wi-Fi is on.
Frequently asked questions
What does AGC do on the MAX9814?
It lowers the gain for loud sounds and raises it for quiet ones, so the output stays in range.
How do I change the gain?
Leave GAIN open for 60 dB, connect it to GND for 50 dB or to VDD for 40 dB.
Does it work at 3.3 V?
Yes, from 2.7 to 5.5 V.
Can it measure decibels?
Not reliably, because the gain changes. Use the MAX4466 for that.
Is it good for voice-activated projects?
Yes, the AGC makes speech detection work in both quiet and noisy rooms.
Parts for this guide
Keep learning
Sources
- MAX9814 microphone amplifier with AGC and low-noise bias datasheet (Maxim Integrated)
- Adafruit AGC electret microphone amplifier MAX9814 guide
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


