Component guide · Intermediate · 3 min read
MEMS and Differential Pressure Sensors

HX710B, MPX, ADP2000 and Airflow Measurements
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
MEMS pressure sensors measure small pressures cheaply. Gauge sensors compare against the air outside, and differential sensors compare two ports, which is how airflow, filter blockage and small level changes are measured. HX710B modules give a 24-bit reading over a simple two-wire interface, while ADP2000-class sensors give calibrated digital readings over I2C. Pick the pressure range first.
Key specs at a glance
- Ranges
- ±125 Pa to 700 kPa depending on the part
- Types
- Gauge, differential, absolute
- HX710B module
- 0-40 kPa, 24-bit ADC, two-wire clocked interface
- Analog parts
- MPX5700AP, APR5852 ratiometric output
- I2C parts
- Asair ADP2000/ADP2100/ADP810
- Media
- Dry air or non-corrosive gas on most MEMS sensors
Gauge, absolute or differential
A gauge sensor reads pressure relative to the surrounding air. An absolute sensor reads against a vacuum; barometers are absolute, see barometric pressure sensors. A differential sensor has two ports and reads the difference, used for airflow, filter checks and flow meters; see industrial flow meters.
| Sensor | Range | Interface |
|---|---|---|
| HX710B module | 0 to 40 kPa | Clock and data (2-wire), 24-bit |
| MPX5700AP (DFRobot Gravity) | 15 to 700 kPa | Analog, ratiometric |
| APR5852 | -10 to 10 kPa differential | Analog |
| Asair ADP2000 | ±125 Pa | I2C, digital |
| Asair ADP2100 | ±500 Pa | I2C, digital |
| GZP6895 series | 0 to 100/500 kPa | Analog, 5 V |
- HX710B module
- Range:
- 0 to 40 kPa
- Interface:
- Clock and data (2-wire), 24-bit
- MPX5700AP (DFRobot Gravity)
- Range:
- 15 to 700 kPa
- Interface:
- Analog, ratiometric
- APR5852
- Range:
- -10 to 10 kPa differential
- Interface:
- Analog
- Asair ADP2000
- Range:
- ±125 Pa
- Interface:
- I2C, digital
- Asair ADP2100
- Range:
- ±500 Pa
- Interface:
- I2C, digital
- GZP6895 series
- Range:
- 0 to 100/500 kPa
- Interface:
- Analog, 5 V
Wiring and reading
For analog sensors, power at the stated voltage and read the output with an ADC; because the output is ratiometric, use the same reference as the supply. For the HX710B, connect DOUT and SCK to two pins and use a library to clock out 24 bits. For I2C parts connect SDA and SCL and read the register. Use the pressure converter to switch between Pa, kPa, psi and bar, and the ADC resolution tool to see what resolution you get.
Tubing and mounting
Use flexible silicone tubing that fits snugly on the port. Keep tubes short and free of kinks, mount the sensor upright where condensation cannot enter, and add a small water trap if humid air is present. Do not blow into the port or exceed the maximum pressure, because the membrane is fragile.
Typical projects
- Airflow and fan monitoring in ventilation ducts. - Detecting clogged filters in air purifiers. - Water level by measuring pressure in a sealed tube. - Breath and respiration sensors. - Weather and altitude with absolute sensors. For high-pressure liquids use a stainless pressure transducer.
Try it: Pressure converter calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Choosing a range far larger than the pressure you measure.
- Exceeding the sensor's maximum overpressure.
- Using a gauge sensor for altitude.
- Ignoring supply voltage on ratiometric sensors.
- Letting liquid or condensation reach a dry-gas sensor.
Frequently asked questions
What is a differential pressure sensor?
A sensor with two ports that measures the pressure difference between them.
Is the HX710B accurate?
It gives a high-resolution reading, but you must calibrate and check temperature drift.
Can I measure water level?
Yes, by reading the pressure of a water column through a tube.
Do I need to calibrate?
Zero the reading at atmospheric pressure and check against a reference.
Can these sensors handle liquids?
Most MEMS parts are for dry air or gas only.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






