Component guide · Beginner · 3 min read
NEO-7M and NEO-8M (M8L-03A) GPS Modules

u-blox NEO-M8M with Ceramic Antenna and M5Stack ATOMIC GPS Base
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
NEO-7M and NEO-8M modules are the next step up from the NEO-6M: faster fixes and, on M8 parts, GPS plus GLONASS or BeiDou. They output standard NMEA at 9600 baud, so TinyGPSPlus works without changes. Use them for trackers, clocks, data loggers and robots. The M5Stack ATOMIC GPS base is a ready board for the ATOM Lite with an SD card slot.
Key specs at a glance
- Chip
- u-blox NEO-7M, NEO-M8M or compatible M8
- Systems
- GPS (7M); GPS + GLONASS or BeiDou (M8)
- Accuracy
- About 2.5 m
- Interface
- UART 9600 baud (default)
- Supply
- 3.3 to 5 V (module regulator)
- Antenna
- Ceramic patch, often with SMA option
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1NEO-7M GPS Module with SMA Antenna₹655
Option 2NEO-7M GPS Satellite Positioning Module for Arduino₹569
Option 3NEO-8M GPS Positioning Module Development Board M8L-03A-12₹1,129
Option 4NEO-8M GPS Satellite Positioning Module Development Board₹1,185
Option 5NEO-M8M GPS Module w/ Ceramic Active Antenna₹1,049
Option 6M5Stack ATOMIC GPS Base w/ M8030-KT Chip₹2,829
What the NEO-7M and NEO-8M GPS modules is
The u-blox NEO-7M and NEO-8M (often GY-GPS6MV2-style boards) are GPS modules that output NMEA position, speed and time over UART for trackers, drones and clocks.
The first fix after power-up (cold start) can take a minute or more outdoors. The backup battery on most boards keeps data so the next start is much faster.
The module's RX pin is 3.3 V; with a 5 V Uno use a divider or just leave RX unconnected if you only read data.
NEO-7M and NEO-8M GPS modules pinout
The pins on the NEO-7M and NEO-8M GPS modules and what each one does.
| Pin | Function |
|---|---|
| VCC | 3.3 to 5 V |
| GND | Ground |
| TX | NMEA out |
| RX | Commands in (3.3 V) |
| PPS | Time pulse (some boards) |
- VCC
- 3.3 to 5 V
- GND
- Ground
- TX
- NMEA out
- RX
- Commands in (3.3 V)
- PPS
- Time pulse (some boards)
Wiring the NEO-7M and NEO-8M GPS modules
Connect the NEO-7M and NEO-8M GPS modules like this.
| NEO-7M and NEO-8M GPS modules pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5 V (or 3.3 V, check module) | 3V3 or 5 V (check module) |
| GND | GND | GND |
| TX | D4 (SoftwareSerial RX) | GPIO 16 (RX2) |
| RX | D3 (SoftwareSerial TX, via divider if 3.3 V) | GPIO 17 (TX2) |
- VCC
- Arduino Uno:
- 5 V (or 3.3 V, check module)
- ESP32:
- 3V3 or 5 V (check module)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- TX
- Arduino Uno:
- D4 (SoftwareSerial RX)
- ESP32:
- GPIO 16 (RX2)
- RX
- Arduino Uno:
- D3 (SoftwareSerial TX, via divider if 3.3 V)
- ESP32:
- GPIO 17 (TX2)
Example code
A minimal sketch to check the part works.
// Read position from any NMEA GPS module (TinyGPSPlus library)
#include <TinyGPSPlus.h>
TinyGPSPlus gps;
void setup() {
Serial.begin(115200);
Serial2.begin(9600, SERIAL_8N1, 16, 17); // GPS TX -> GPIO 16. Many modules use 38400 or 115200
}
void loop() {
while (Serial2.available()) gps.encode(Serial2.read());
static unsigned long t = 0;
if (millis() - t > 1000) {
t = millis();
if (gps.location.isValid()) {
Serial.printf("%.6f, %.6f sats %d alt %.1f m\n", gps.location.lat(), gps.location.lng(),
gps.satellites.value(), gps.altitude.meters());
} else {
Serial.printf("Waiting for fix... chars %lu sats %d\n", gps.charsProcessed(), gps.satellites.value());
}
}
}Setup and tuning
VCC 3.3 to 5 V (board regulator), GND, TX to RX and RX to TX.
default 9600 baud.
use TinyGPS++ to parse location and time.
keep the ceramic patch facing the sky.
use u-center to change update rate, systems and save settings.
What you need
Shop this list10 of 11 found in our store · ₹8,722
NEO-7M GPS Module with SMA Antenna: the part this guide coversNEO-7M GPS Module with SMA Antenna₹655
NEO-7M GPS Satellite Positioning Module for Arduino: another version this guide coversNEO-7M GPS Satellite Positioning Module for Arduino₹569
NEO-8M GPS Positioning Module Development Board M8L-03A-12: another version this guide coversNEO-8M GPS Positioning Module Development Board M8L-03A-12₹1,129
NEO-8M GPS Satellite Positioning Module Development Board: another version this guide coversNEO-8M GPS Satellite Positioning Module Development Board₹1,185
NEO-M8M GPS Module w/ Ceramic Active Antenna: another version this guide coversNEO-M8M GPS Module w/ Ceramic Active Antenna₹1,049
M5Stack ATOMIC GPS Base w/ M8030-KT Chip: another version this guide coversM5Stack ATOMIC GPS Base w/ M8030-KT Chip₹2,829- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
GY-NEO6MV2 GPS module (u-blox NEO-6M): the classic beginner GPS moduleGY-NEO6MV2 GPS Module w/ u-blox NEO-6M & Antenna₹499
GPS antenna 1575.42 MHz, SMA, 3 m cable: an external antenna for better receptionGPS Antenna 1575.42MHz SMA Male 3M Cable₹279Closest match, check the specs
Alternatives and when to choose them
- NEO-6M: cheapest classic.
- NEO-M8N: bigger antenna and compass options.
- SparkFun u-blox breakouts: Qwiic and faster rates.
Common mistakes to avoid
- Testing indoors.
- Swapping TX and RX.
- Wrong baud rate.
- Covering the antenna.
Frequently asked questions
Why does my NEO-8M not get a fix?
Take it outdoors with clear sky; first fix can take a few minutes.
Which library should I use?
TinyGPS++ parses position and time well on Arduino, ESP32 and Pico.
Is the NEO-8M better than the NEO-7M?
Yes, it tracks more satellite systems and gets fixes faster.
Can I raise the update rate?
Yes, up to about 5 to 10 Hz using u-center.
Why are many cheap NEO-8M modules different?
Some are clone chips; check that they connect and save settings in u-center.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

