Component guide · Intermediate · 3 min read
SparkFun NEO-M9N, SAM-M8Q, NEO-M8U Dead Reckoning, NEO-F10N L1/L5, XA1110

Mikroe GNSS Clicks and RAK12500
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These breakouts make good GPS easy on Arduino and ESP32. The NEO-M9N tracks four systems at 25 Hz, the SAM-M8Q has a built-in chip antenna, the NEO-M8U adds dead reckoning with an IMU for tunnels, and the NEO-F10N uses L1 and L5 for better accuracy in cities. Mikroe click boards and the RAK12500 WisBlock module bring the same chips to their own systems.
Key specs at a glance
- Chips
- u-blox NEO-M9N, SAM-M8Q, NEO-M8U, NEO-F10N, ZOE-M8Q; MediaTek XA1110
- Accuracy
- About 1.5 to 2.5 m (single band); better with L5
- Update rate
- Up to 25 Hz (M9N)
- Interface
- Qwiic I2C (0x42 u-blox, 0x10 XA1110), UART, SPI
- Supply
- 3.3 V (Qwiic)
- Antenna
- Chip, patch or SMA/U.FL external
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1SparkFun GPS Breakout – NEO-M9N (Qwiic) w/ SMA Antenna₹10,679
Option 2SparkFun GPS Breakout – NEO-M9N U.FL (Qwiic)₹7,599
Option 3SparkFun NEO-M9N GPS Breakout w/ Chip Antenna (Qwiic)₹10,679
Option 4SparkFun SAM-M8Q GPS Breakout w/ Chip Antenna (Qwiic)₹4,159
Option 5SparkFun GPS-16329 NEO-M8U Dead Reckoning GPS Breakout₹11,159
Option 6SparkFun GPS-24114 GNSS L1/L5 Breakout – NEO-F10N, SMA₹6,759
What the SparkFun and Mikroe u-blox GPS breakouts is
SparkFun u-blox GPS breakouts, such as the NEO-M9N, SAM-M10Q and ZED-F9P boards, give accurate GNSS position over I2C (Qwiic), UART or USB.
u-blox modules speak UBX binary as well as NMEA. Over I2C, the SparkFun library reads UBX directly, which is faster and less fussy than parsing text.
Dead reckoning on the M8U keeps a position going when satellites drop out, as long as it is mounted rigidly in the vehicle.
SparkFun and Mikroe u-blox GPS breakouts pinout
The pins on the SparkFun and Mikroe u-blox GPS breakouts and what each one does.
| Pin | Function |
|---|---|
| 3V3 / GND | Supply |
| SDA / SCL | Qwiic I2C |
| TX / RX | UART |
| PPS | Time pulse |
| INT / RST | Interrupt and reset |
- 3V3 / GND
- Supply
- SDA / SCL
- Qwiic I2C
- TX / RX
- UART
- PPS
- Time pulse
- INT / RST
- Interrupt and reset
Wiring the SparkFun and Mikroe u-blox GPS breakouts
Connect the SparkFun and Mikroe u-blox GPS breakouts like this.
| SparkFun and Mikroe u-blox GPS breakouts pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5V (or 3.3V) | 3V3 |
| GND | GND | GND |
| SDA | A4 | GPIO 21 |
| SCL | A5 | GPIO 22 |
- VCC
- Arduino Uno:
- 5V (or 3.3V)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SDA
- Arduino Uno:
- A4
- ESP32:
- GPIO 21
- SCL
- Arduino Uno:
- A5
- ESP32:
- GPIO 22
Example code
The XA1110 uses SparkFun's I2C GPS library and outputs NMEA; feed it to TinyGPSPlus.
// u-blox module over I2C/Qwiic (SparkFun u-blox GNSS v3 library)
#include <Wire.h>
#include <SparkFun_u-blox_GNSS_v3.h>
SFE_UBLOX_GNSS gnss;
void setup() {
Serial.begin(115200);
Wire.begin();
while (!gnss.begin()) { Serial.println("u-blox not found at 0x42"); delay(1000); }
gnss.setI2COutput(COM_TYPE_UBX); // binary only on I2C
}
void loop() {
if (gnss.getPVT()) {
Serial.printf("lat %.7f lon %.7f sats %d fix %d carrSoln %d\n",
gnss.getLatitude() / 1e7, gnss.getLongitude() / 1e7,
gnss.getSIV(), gnss.getFixType(), gnss.getCarrierSolutionType());
}
}Setup and tuning
plug a Qwiic cable for quick I2C wiring at 3.3 V.
use the SparkFun u-blox GNSS Arduino library.
use the on-board chip antenna or an external active antenna.
set navigation rate and messages in code or u-center.
keep the coin cell or supercap for faster fixes.
What you need
Shop this list14 of 14 found in our store · ₹76,296
SparkFun GPS Breakout – NEO-M9N (Qwiic) w/ SMA Antenna: the part this guide coversSparkFun GPS Breakout – NEO-M9N (Qwiic) w/ SMA Antenna₹10,679
SparkFun GPS Breakout – NEO-M9N U.FL (Qwiic): another version this guide coversSparkFun GPS Breakout – NEO-M9N U.FL (Qwiic)₹7,599
SparkFun NEO-M9N GPS Breakout w/ Chip Antenna (Qwiic): another version this guide coversSparkFun NEO-M9N GPS Breakout w/ Chip Antenna (Qwiic)₹10,679
SparkFun SAM-M8Q GPS Breakout w/ Chip Antenna (Qwiic): another version this guide coversSparkFun SAM-M8Q GPS Breakout w/ Chip Antenna (Qwiic)₹4,159
SparkFun GPS-16329 NEO-M8U Dead Reckoning GPS Breakout: another version this guide coversSparkFun GPS-16329 NEO-M8U Dead Reckoning GPS Breakout₹11,159
SparkFun GPS-24114 GNSS L1/L5 Breakout – NEO-F10N, SMA: another version this guide coversSparkFun GPS-24114 GNSS L1/L5 Breakout – NEO-F10N, SMA₹6,759
SparkFun XA1110 GPS Breakout – Qwiic, I2C/Serial: another version this guide coversSparkFun XA1110 GPS Breakout – Qwiic, I2C/Serial₹5,009
Mikroe GNSS 10 CLICK NEO-M8J Multi-GNSS Receiver: another version this guide coversMikroe GNSS 10 CLICK NEO-M8J Multi-GNSS Receiver₹5,159
Mikroe GNSS MAX CLICK u-blox MAX-M10S GPS Receiver UART I²C: another version this guide coversMikroe GNSS MAX CLICK u-blox MAX-M10S GPS Receiver UART I²C₹7,349
Mikroe GPS 6 Click A2200-A Receiver Board 1.575MHz L1 GPS: another version this guide coversMikroe GPS 6 Click A2200-A Receiver Board 1.575MHz L1 GPS₹4,139
RAKwireless WisBlock GNSS Location Module RAK12500 w/ u-blox ZOE-M8Q: another version this guide coversRAKwireless WisBlock GNSS Location Module RAK12500 w/ u-blox ZOE-M8Q₹2,799
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
GPS antenna 1575.42 MHz, SMA, 3 m cable: an external antenna for better receptionGPS Antenna 1575.42MHz SMA Male 3M Cable₹279Closest match, check the specs
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Alternatives and when to choose them
- ZED-F9P RTK: centimetre accuracy.
- NEO-M8N: low-cost u-blox module.
- Low-cost GNSS modules: cheaper chips.
Common mistakes to avoid
- 5 V logic on Qwiic.
- Testing indoors.
- Draining the backup battery.
- Wrong library version.
Frequently asked questions
Which SparkFun GPS board should I start with?
The SAM-M10Q or NEO-M9N boards are easy starting points for accurate GPS.
Why use I2C instead of UART?
Qwiic I2C is easy and the library uses UBX binary messages.
How fast can it update?
Up to 10 to 25 Hz depending on module.
Why is the first fix slow?
It is a cold start; keep the backup battery charged for faster fixes.
Do I need an external antenna?
Only when the board is inside an enclosure or far from the sky.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
