Component guide · Beginner · 4 min read
Low-Cost GNSS

Seeed L76K for XIAO, Grove Air530, Ai-Thinker GP-02, EByte E108, Quectel L89H and L80, USB GPS, ADH-Tech GP Modules
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These modules give GPS, BeiDou and GLONASS positions at low cost and low power. The Seeed L76K plugs onto a XIAO, the Grove Air530 plugs into a Grove port, the Ai-Thinker GP-02 and EByte E108 are tiny modules for your own PCB, the Quectel L89H adds NavIC and dual band, and the USB receivers plug straight into a Raspberry Pi. All output NMEA text.
Key specs at a glance
- Chips
- Quectel L76K, L80, L89H; AirM2M Air530; AT6558-class (GP-02, E108); MediaTek (ADH-Tech)
- Systems
- GPS, BeiDou, GLONASS; NavIC on L89H
- Accuracy
- About 2 to 3 m
- Interface
- UART 9600 or 115200; USB on USB receivers
- Supply
- 3.3 V (Grove and XIAO boards 3.3 to 5 V)
- Power
- About 20 to 40 mA tracking
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Seeed Studio L76K Multi-GNSS Module for XIAO₹1,829
Option 2Seeed Studio Grove GPS (Air530) Multi-Mode GNSS Module₹1,349
Option 3AI-Thinker GP-02 GPS Receiver Module, BDS/GLONASS₹249
Option 4Ai-Thinker GP-02-Kit GNSS Development Board₹545
Option 5EByte E108-GN02D 10Hz BDS/GPS/GLONASS GPS Module₹759
Option 6CAPUF L89H-GPS Breakout Board₹1,979
What the Low-cost GNSS modules (L76K, GP-02, Air530, E108) is
Low-cost GNSS modules such as the Quectel L76K and ATGM336H or GP-02 track GPS, BeiDou and GLONASS and send NMEA position over UART, for trackers and clocks.
All of these send NMEA sentences, so TinyGPSPlus reads them unchanged. Some default to 115200 baud; if you see garbage, try other rates.
USB receivers appear as a serial port on the Pi (for example /dev/ttyACM0) and work with gpsd.
Low-cost GNSS modules (L76K, GP-02, Air530, E108) pinout
The pins on the Low-cost GNSS modules (L76K, GP-02, Air530, E108) and what each one does.
| Pin | Function |
|---|---|
| VCC | Supply |
| GND | Ground |
| TX | NMEA out |
| RX | Commands in |
| PPS / 1PPS | Time pulse (some) |
- VCC
- Supply
- GND
- Ground
- TX
- NMEA out
- RX
- Commands in
- PPS / 1PPS
- Time pulse (some)
Wiring the Low-cost GNSS modules (L76K, GP-02, Air530, E108)
Connect the Low-cost GNSS modules (L76K, GP-02, Air530, E108) like this.
| Low-cost GNSS modules (L76K, GP-02, Air530, E108) pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5 V (or 3.3 V, check module) | 3V3 or 5 V (check module) |
| GND | GND | GND |
| TX | D4 (SoftwareSerial RX) | GPIO 16 (RX2) |
| RX | D3 (SoftwareSerial TX, via divider if 3.3 V) | GPIO 17 (TX2) |
- VCC
- Arduino Uno:
- 5 V (or 3.3 V, check module)
- ESP32:
- 3V3 or 5 V (check module)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- TX
- Arduino Uno:
- D4 (SoftwareSerial RX)
- ESP32:
- GPIO 16 (RX2)
- RX
- Arduino Uno:
- D3 (SoftwareSerial TX, via divider if 3.3 V)
- ESP32:
- GPIO 17 (TX2)
Example code
Change the baud in Serial2.begin if your module defaults to 115200.
// Read position from any NMEA GPS module (TinyGPSPlus library)
#include <TinyGPSPlus.h>
TinyGPSPlus gps;
void setup() {
Serial.begin(115200);
Serial2.begin(9600, SERIAL_8N1, 16, 17); // GPS TX -> GPIO 16. Many modules use 38400 or 115200
}
void loop() {
while (Serial2.available()) gps.encode(Serial2.read());
static unsigned long t = 0;
if (millis() - t > 1000) {
t = millis();
if (gps.location.isValid()) {
Serial.printf("%.6f, %.6f sats %d alt %.1f m\n", gps.location.lat(), gps.location.lng(),
gps.satellites.value(), gps.altitude.meters());
} else {
Serial.printf("Waiting for fix... chars %lu sats %d\n", gps.charsProcessed(), gps.satellites.value());
}
}
}Setup and tuning
VCC (3.3 V or 5 V on breakouts), GND, TX to the microcontroller RX, RX to TX.
default is usually 9600 baud.
use TinyGPS++ to parse NMEA sentences into latitude, longitude and time.
use the ceramic patch facing the sky, or an active antenna for boxes.
wait outdoors for 30 s to a few minutes; a backup battery speeds later fixes.
What you need
Shop this list15 of 15 found in our store · ₹24,192
Seeed Studio Studio L76K Multi-GNSS Module for XIAO: the part this guide coversSeeed Studio L76K Multi-GNSS Module for XIAO₹1,829Closest match, check the specs
Seeed Studio Studio Grove GPS (Air530) Multi-Mode GNSS Module: another version this guide coversSeeed Studio Grove GPS (Air530) Multi-Mode GNSS Module₹1,349Closest match, check the specs
AI-Thinker GP-02 GPS Receiver Module, BDS/GLONASS: another version this guide coversAI-Thinker GP-02 GPS Receiver Module, BDS/GLONASS₹249
Ai-Thinker GP-02-Kit GNSS Development Board: another version this guide coversAi-Thinker GP-02-Kit GNSS Development Board₹545
EByte E108-GN02D 10Hz BDS/GPS/GLONASS GPS Module: another version this guide coversEByte E108-GN02D 10Hz BDS/GPS/GLONASS GPS Module₹759
CAPUF L89H-GPS Breakout Board: another version this guide coversCAPUF L89H-GPS Breakout Board₹1,979
Raspberry Pi USB GPS Module L80-39: another version this guide coversRaspberry Pi USB GPS Module L80-39₹1,929
DFRobot USB GPS Receiver with 2m Cable for SBCs: another version this guide coversDFRobot USB GPS Receiver with 2m Cable for SBCs₹1,729
ADH-Tech GP-1513 GPS Module – MediaTek MT3339: another version this guide coversADH-Tech GP-1513 GPS Module – MediaTek MT3339₹979
ADH-Tech GP-735 56-Channel GPS Receiver Module: another version this guide coversADH-Tech GP-735 56-Channel GPS Receiver Module₹7,371
ADH-Tech GP1818MK 56-Channel GPS Module: another version this guide coversADH-Tech GP1818MK 56-Channel GPS Module₹4,168
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
GPS antenna 1575.42 MHz, SMA, 3 m cable: an external antenna for better receptionGPS Antenna 1575.42MHz SMA Male 3M Cable₹279Closest match, check the specs
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
GY-NEO6MV2 GPS module (u-blox NEO-6M): the classic beginner GPS moduleGY-NEO6MV2 GPS Module w/ u-blox NEO-6M & Antenna₹499
Alternatives and when to choose them
- NEO-7M and NEO-8M: u-blox modules.
- Reyax modules: ultra-low power and L1/L5.
- NavIC modules: Indian NavIC support.
Common mistakes to avoid
- Testing indoors.
- Swapping TX and RX.
- Using the wrong baud rate.
- Covering the patch antenna with metal.
Frequently asked questions
Why does my GPS module never get a fix?
It needs a clear sky view; indoors it often cannot see enough satellites.
Which library should I use?
TinyGPS++ parses NMEA sentences on Arduino, ESP32 and Pico.
Does the L76K support NavIC?
No. It tracks GPS, BeiDou and GLONASS; choose a NavIC module for NavIC.
What does the PPS pin do?
It gives a precise pulse each second for accurate timing.
Why do I see only commas in NMEA?
Empty fields mean the module has no fix yet; take it outdoors and wait a few minutes.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
