Component guide · Intermediate · 3 min read
NavIC GNSS

GNSS Receiver Breakout with NavIC and GPS, EdgeHax NavIC L1/L5 Tracker and Dual-Band Antenna
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
NavIC is India's regional satellite navigation system. Receivers that use NavIC alongside GPS see more satellites over India and use the L5 band, which helps accuracy in cities. The GNSS breakout with NavIC outputs standard NMEA over UART; the EdgeHax tracker has an on-board L1 and L5 patch; and the EdgeHax dual-band antenna suits any L1/L5 receiver.
Key specs at a glance
- Systems
- NavIC (IRNSS) plus GPS, often GLONASS, Galileo, BeiDou
- Bands
- L1 and L5
- Interface
- UART NMEA
- Supply
- 3.3 to 5 V (check board)
- Coverage
- NavIC covers India and about 1,500 km around
- Antenna
- Dual-band L1/L5 needed
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1GNSS Receiver BOB with NavIC & GPS₹2,599
Option 2EdgeHax NavIC GPS Tracker L1 + L5 Onboard Patch Antenna₹2,469
Option 3EdgeHax NavIC GPS L1/L5 Dual-Band Antenna₹2,589
What the NavIC GNSS receivers and antennas is
NavIC GNSS modules receive India's own NavIC (IRNSS) satellites along with GPS and other systems, for trackers, telematics and devices that must support NavIC.
NavIC satellites appear in NMEA as their own talker ID ($GI or $GN combined). TinyGPSPlus reads the combined position without changes.
A single-band L1 antenna will not receive NavIC L5; use a dual-band antenna.
NavIC GNSS receivers and antennas pinout
The pins on the NavIC GNSS receivers and antennas and what each one does.
| Pin | Function |
|---|---|
| VCC | Supply |
| GND | Ground |
| TX | NMEA out |
| RX | Commands in |
| RF | Antenna (SMA or U.FL) |
- VCC
- Supply
- GND
- Ground
- TX
- NMEA out
- RX
- Commands in
- RF
- Antenna (SMA or U.FL)
Wiring the NavIC GNSS receivers and antennas
Connect the NavIC GNSS receivers and antennas like this.
| NavIC GNSS receivers and antennas pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5 V (or 3.3 V, check module) | 3V3 or 5 V (check module) |
| GND | GND | GND |
| TX | D4 (SoftwareSerial RX) | GPIO 16 (RX2) |
| RX | D3 (SoftwareSerial TX, via divider if 3.3 V) | GPIO 17 (TX2) |
- VCC
- Arduino Uno:
- 5 V (or 3.3 V, check module)
- ESP32:
- 3V3 or 5 V (check module)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- TX
- Arduino Uno:
- D4 (SoftwareSerial RX)
- ESP32:
- GPIO 16 (RX2)
- RX
- Arduino Uno:
- D3 (SoftwareSerial TX, via divider if 3.3 V)
- ESP32:
- GPIO 17 (TX2)
Example code
A minimal sketch to check the part works.
// Read position from any NMEA GPS module (TinyGPSPlus library)
#include <TinyGPSPlus.h>
TinyGPSPlus gps;
void setup() {
Serial.begin(115200);
Serial2.begin(9600, SERIAL_8N1, 16, 17); // GPS TX -> GPIO 16. Many modules use 38400 or 115200
}
void loop() {
while (Serial2.available()) gps.encode(Serial2.read());
static unsigned long t = 0;
if (millis() - t > 1000) {
t = millis();
if (gps.location.isValid()) {
Serial.printf("%.6f, %.6f sats %d alt %.1f m\n", gps.location.lat(), gps.location.lng(),
gps.satellites.value(), gps.altitude.meters());
} else {
Serial.printf("Waiting for fix... chars %lu sats %d\n", gps.charsProcessed(), gps.satellites.value());
}
}
}Setup and tuning
common chips include Quectel L89, u-blox NEO-M9N variants and others that list NavIC support.
connect UART TX and RX, power and a suitable L5 or S-band capable antenna.
NavIC uses the L5 band; use an antenna that covers L1 and L5.
enable NavIC in the module configuration if it is off by default.
parse NMEA sentences with TinyGPS++; NavIC satellites appear with their own IDs.
What you need
Shop this list6 of 6 found in our store · ₹8,270
GNSS Receiver BOB with NavIC & GPS: the part this guide coversGNSS Receiver BOB with NavIC & GPS₹2,599
EdgeHax NavIC GPS Tracker L1 + L5 Onboard Patch Antenna: another version this guide coversEdgeHax NavIC GPS Tracker L1 + L5 Onboard Patch Antenna₹2,469
EdgeHax NavIC GPS L1/L5 Dual-Band Antenna: another version this guide coversEdgeHax NavIC GPS L1/L5 Dual-Band Antenna₹2,589
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
Alternatives and when to choose them
- Low-cost GNSS modules: includes Quectel L89H with NavIC.
- Reyax RYS8839: L1/L5 module.
- NEO-M8N: GPS without NavIC.
Common mistakes to avoid
- Using an L1-only antenna.
- Not enabling NavIC in config.
- Testing indoors.
- Swapping TX and RX.
Frequently asked questions
What is NavIC?
NavIC is India's regional satellite navigation system, also called IRNSS.
Do I need a special antenna for NavIC?
Yes, one that covers the L5 band as well as L1.
Does NavIC work outside India?
Its coverage is India and about 1500 km around it.
Can I use NavIC with Arduino?
Yes. Read the NMEA output over UART with TinyGPS++ or a similar parser.
Why is NavIC required for some devices?
Indian rules require NavIC support in some vehicle trackers and public transport devices.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
