Component guide · Intermediate · 3 min read
Reyax RYS3520, RYS352A, RYS8830, RYS8833, RYS8838

and RYS8839 L1/L5 GNSS Modules and Lite Evaluation Boards
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Reyax GNSS modules are small, low-power receivers with embedded antennas for trackers and wearables. The RYS8830 and RYS8833 run at very low current; the RYS8833 uses 1.8 V logic; the RYS8838 is a 3.3 V UART version; and the RYS8839 adds L1 and L5 dual band for better accuracy near buildings. The Lite boards are DIP evaluation versions for breadboards.
Key specs at a glance
- Systems
- GPS, GLONASS, Galileo, BeiDou, QZSS (model dependent)
- Bands
- L1, or L1 and L5 (RYS8839)
- Interface
- UART (I2C on RYS8833)
- Logic
- 1.8 V (RYS8833) or 3.3 V
- Antenna
- Embedded
- Power
- Very low, suits battery trackers
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Reyax RYS3520 GNSS Module w/ 3.3V UART Interface₹839
Option 2Reyax RYS3520_LITE GNSS Antenna Module Lite Evaluation Board DIP Version₹1,329
Option 3Reyax RYS352A Multi-GNSS Module w/ Embedded Antenna & UART Interface₹1,679
Option 4Reyax RYS8830 Ultra-Low Power GNSS Module w/ Embedded Antenna₹1,819
Option 5Reyax RYS8833 Ultra Low Power 1.8V UART/I2C GNSS Module₹904
Option 6Reyax RYS8833_LITE Ultra Low Power 1.8V GNSS Module₹1,919
What the Reyax RYS GNSS modules is
Reyax GNSS modules, such as the RYS8830 and RYS352A, are small multi-constellation GPS receivers with UART output for trackers, drones and IoT devices.
Check the logic level: the 1.8 V parts need a level shifter even on an ESP32. The 3.3 V versions connect directly.
Embedded antennas need clear sky and the module near the top of the enclosure, away from batteries and metal.
Reyax RYS GNSS modules pinout
The pins on the Reyax RYS GNSS modules and what each one does.
| Pin | Function |
|---|---|
| VCC | Supply (1.8 or 3.3 V) |
| GND | Ground |
| TXD / RXD | UART |
| SDA / SCL | I2C (RYS8833) |
| 1PPS | Time pulse |
| RESET | Reset |
- VCC
- Supply (1.8 or 3.3 V)
- GND
- Ground
- TXD / RXD
- UART
- SDA / SCL
- I2C (RYS8833)
- 1PPS
- Time pulse
- RESET
- Reset
Wiring the Reyax RYS GNSS modules
1.8 V models need a level shifter on every signal line.
| Reyax RYS GNSS modules pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 3.3 V (3.3 V models only) | 3V3 |
| GND | GND | GND |
| TXD | D4 via level shifter | GPIO 16 |
| RXD | D3 via level shifter | GPIO 17 |
- VCC
- Arduino Uno:
- 3.3 V (3.3 V models only)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- TXD
- Arduino Uno:
- D4 via level shifter
- ESP32:
- GPIO 16
- RXD
- Arduino Uno:
- D3 via level shifter
- ESP32:
- GPIO 17
Example code
Set the baud to the module's default (often 115200).
// Read position from any NMEA GPS module (TinyGPSPlus library)
#include <TinyGPSPlus.h>
TinyGPSPlus gps;
void setup() {
Serial.begin(115200);
Serial2.begin(9600, SERIAL_8N1, 16, 17); // GPS TX -> GPIO 16. Many modules use 38400 or 115200
}
void loop() {
while (Serial2.available()) gps.encode(Serial2.read());
static unsigned long t = 0;
if (millis() - t > 1000) {
t = millis();
if (gps.location.isValid()) {
Serial.printf("%.6f, %.6f sats %d alt %.1f m\n", gps.location.lat(), gps.location.lng(),
gps.satellites.value(), gps.altitude.meters());
} else {
Serial.printf("Waiting for fix... chars %lu sats %d\n", gps.charsProcessed(), gps.satellites.value());
}
}
}Setup and tuning
VCC (3.3 V), GND, TX and RX to the microcontroller.
check the default (often 115200 or 9600) in the datasheet.
use the built-in antenna with sky view, or an external active antenna.
use TinyGPS++ for NMEA sentences.
use standby modes for battery trackers.
What you need
Shop this list12 of 12 found in our store · ₹16,930
Reyax RYS3520 GNSS Module w/ 3.3V UART Interface: the part this guide coversReyax RYS3520 GNSS Module w/ 3.3V UART Interface₹839
Reyax RYS3520LITE GNSS Antenna Module Lite Evaluation Board DIP Version: another version this guide coversReyax RYS3520_LITE GNSS Antenna Module Lite Evaluation Board DIP Version₹1,329
Reyax RYS352A Multi-GNSS Module w/ Embedded Antenna & UART Interface: another version this guide coversReyax RYS352A Multi-GNSS Module w/ Embedded Antenna & UART Interface₹1,679
Reyax RYS8830 Ultra-Low Power GNSS Module w/ Embedded Antenna: another version this guide coversReyax RYS8830 Ultra-Low Power GNSS Module w/ Embedded Antenna₹1,819
Reyax RYS8833 Ultra Low Power 1.8V UART/I2C GNSS Module: another version this guide coversReyax RYS8833 Ultra Low Power 1.8V UART/I2C GNSS Module₹904
Reyax RYS8833LITE Ultra Low Power 1.8V GNSS Module: another version this guide coversReyax RYS8833_LITE Ultra Low Power 1.8V GNSS Module₹1,919
Reyax RYS8838 3.3V UART GNSS Module: another version this guide coversReyax RYS8838 3.3V UART GNSS Module₹3,649
Reyax RYS8839 Ultra-Low Power L1 L5 Dual-Band GNSS Module: another version this guide coversReyax RYS8839 Ultra-Low Power L1 L5 Dual-Band GNSS Module₹1,589
Reyax RYS8839LITE L1/L5 Dual-Band GNSS Module Lite Evaluation Board: another version this guide coversReyax RYS8839_LITE L1/L5 Dual-Band GNSS Module Lite Evaluation Board₹2,709
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
4-channel logic level converter (BSS138): to connect 5 V and 3.3 V signals safely4-Channel Logic Level Converter (BSS138)₹20
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
Alternatives and when to choose them
- Low-cost GNSS modules: cheaper modules.
- SparkFun NEO-F10N: u-blox L1/L5.
- NavIC modules: NavIC support.
Common mistakes to avoid
- 5 V logic.
- Wrong baud rate.
- Testing indoors.
- Covering the antenna.
Frequently asked questions
Which baud rate do Reyax GNSS modules use?
Check the datasheet for your model; many Reyax modules default to 115200 baud.
Why does it not get a fix indoors?
GNSS signals are too weak indoors, so test outside with a clear sky view.
Can it track NavIC?
Some Reyax models support NavIC; check the datasheet of your exact model.
Can I use it with Arduino?
Yes, over UART, using level shifting on 5 V Arduino boards.
How do I save power?
Use the module's standby or backup modes between fixes to save battery.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
