Component guide · Advanced · 3 min read
RTK GNSS Breakouts

SparkFun ZED-F9P (RTK2 Qwiic and SMA), ZED-X20P, LG290P Quad-Band, GNSS Flex pHAT and Waveshare NEO-F9P
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These boards bring centimetre-level RTK to Arduino, ESP32 and Raspberry Pi projects such as rovers, lawn robots and surveying. The u-blox ZED-F9P is the standard dual-band choice; the ZED-X20P adds all bands; Quectel's LG290P is a quad-band low-cost alternative; and the Waveshare NEO-F9P and SparkFun Flex pHAT suit the Pi. Corrections come from your own base or an NTRIP service.
Key specs at a glance
- Receivers
- ZED-F9P, ZED-X20P, NEO-F9P (u-blox), LG290P (Quectel)
- Bands
- L1/L2 (F9P), L1/L2/L5/L6 (X20P, LG290P)
- Accuracy
- About 1 cm + 1 ppm with corrections
- Interface
- Qwiic I2C, UART, SPI, USB
- Antenna
- External multiband via SMA or U.FL
- Supply
- 3.3 V (5 V via USB or Qwiic boards)
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1SparkFun GPS-RTK2 Board ZED-F9P (Qwiic)₹35,969
Option 2SparkFun GPS-RTK Breakout – ZED-F9P, SMA Antenna₹38,149
Option 3SparkFun ZED-X20P GNSS RTK Breakout (Qwiic)₹39,189
Option 4SparkFun GNSS RTK Breakout – Quad-Band LG290P (Qwiic)₹26,509
Option 5SparkPNT GPS-28139 GNSS Flex Module w/ LG290P, Quad-Band RTK₹14,804
Option 6SparkFun GPS-28137 GNSS Flex pHAT for Raspberry Pi₹3,700
What the ZED-F9P, LG290P and NEO-F9P RTK breakouts is
RTK GNSS breakouts with the u-blox ZED-F9P, such as SparkFun and Ardusimple boards, give centimetre-level position when they receive RTK corrections from a base or NTRIP service.
RTK needs RTCM corrections. On an ESP32 with Wi-Fi you can pull them from an NTRIP caster and push them into the receiver's UART; SparkFun's examples show how.
Use a proper multiband antenna with a ground plane; a cheap L1 patch will never reach RTK Fixed.
ZED-F9P, LG290P and NEO-F9P RTK breakouts pinout
The pins on the ZED-F9P, LG290P and NEO-F9P RTK breakouts and what each one does.
| Pin | Function |
|---|---|
| 3V3 / GND | Supply |
| SDA / SCL | Qwiic I2C (0x42 u-blox) |
| TX / RX | UART |
| PPS | Time pulse |
| RTK | RTK status LED |
- 3V3 / GND
- Supply
- SDA / SCL
- Qwiic I2C (0x42 u-blox)
- TX / RX
- UART
- PPS
- Time pulse
- RTK
- RTK status LED
Wiring the ZED-F9P, LG290P and NEO-F9P RTK breakouts
Connect the ZED-F9P, LG290P and NEO-F9P RTK breakouts like this.
| ZED-F9P, LG290P and NEO-F9P RTK breakouts pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5V (or 3.3V) | 3V3 |
| GND | GND | GND |
| SDA | A4 | GPIO 21 |
| SCL | A5 | GPIO 22 |
- VCC
- Arduino Uno:
- 5V (or 3.3V)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SDA
- Arduino Uno:
- A4
- ESP32:
- GPIO 21
- SCL
- Arduino Uno:
- A5
- ESP32:
- GPIO 22
Example code
carrSoln: 0 none, 1 RTK float, 2 RTK fixed. The LG290P uses NMEA and Quectel commands instead of this library.
// u-blox module over I2C/Qwiic (SparkFun u-blox GNSS v3 library)
#include <Wire.h>
#include <SparkFun_u-blox_GNSS_v3.h>
SFE_UBLOX_GNSS gnss;
void setup() {
Serial.begin(115200);
Wire.begin();
while (!gnss.begin()) { Serial.println("u-blox not found at 0x42"); delay(1000); }
gnss.setI2COutput(COM_TYPE_UBX); // binary only on I2C
}
void loop() {
if (gnss.getPVT()) {
Serial.printf("lat %.7f lon %.7f sats %d fix %d carrSoln %d\n",
gnss.getLatitude() / 1e7, gnss.getLongitude() / 1e7,
gnss.getSIV(), gnss.getFixType(), gnss.getCarrierSolutionType());
}
}Setup and tuning
use a multi-band (L1/L2 or L1/L5) antenna with a ground plane.
feed RTCM corrections from a second F9P base or an NTRIP caster over radio, LoRa or the internet.
connect over UART, I2C or USB; configure with u-center.
use the SparkFun u-blox GNSS library for Arduino.
wait for RTK Fixed for centimetre accuracy; RTK Float is decimetre level.
What you need
Shop this list10 of 10 found in our store · ₹1,93,614
SparkFun GPS-RTK2 Board ZED-F9P (Qwiic): the part this guide coversSparkFun GPS-RTK2 Board ZED-F9P (Qwiic)₹35,969
SparkFun GPS-RTK Breakout – ZED-F9P, SMA Antenna: another version this guide coversSparkFun GPS-RTK Breakout – ZED-F9P, SMA Antenna₹38,149
SparkFun ZED-X20P GNSS RTK Breakout (Qwiic): another version this guide coversSparkFun ZED-X20P GNSS RTK Breakout (Qwiic)₹39,189
SparkFun GNSS RTK Breakout – Quad-Band LG290P (Qwiic): another version this guide coversSparkFun GNSS RTK Breakout – Quad-Band LG290P (Qwiic)₹26,509
SparkPNT GPS-28139 GNSS Flex Module w/ LG290P, Quad-Band RTK: another version this guide coversSparkPNT GPS-28139 GNSS Flex Module w/ LG290P, Quad-Band RTK₹14,804
SparkFun GPS-28137 GNSS Flex pHAT for Raspberry Pi: another version this guide coversSparkFun GPS-28137 GNSS Flex pHAT for Raspberry Pi₹3,700
Waveshare Q43 NEO-F9P Multi-Band GNSS RTK Module: another version this guide coversWaveshare Q43 NEO-F9P Multi-Band GNSS RTK Module₹30,150
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Raspberry Pi 4 Model B (4 GB): to run an RTK base, NTRIP or loggingRaspberry Pi 4 Model B 1GB RAM₹4,476Closest match, check the specs
GPS antenna 1575.42 MHz, SMA, 3 m cable: an external antenna for better receptionGPS Antenna 1575.42MHz SMA Male 3M Cable₹279Closest match, check the specs
Alternatives and when to choose them
- Holybro H-RTK: drone-ready F9P.
- SparkFun u-blox breakouts: metre-level GPS.
- NEO-M8N: low-cost single band.
Common mistakes to avoid
- Using a single-band antenna.
- No corrections.
- Antenna near metal or trees.
- Expecting cm accuracy in Float mode.
Frequently asked questions
What accuracy does a ZED-F9P give?
About 1 to 2 cm with RTK Fixed and good corrections.
Do I need a base station?
Yes, your own base station or an NTRIP correction service within about 30 km.
Why do I only get RTK Float?
Poor sky view, reflections from buildings, or weak and delayed corrections.
Which antenna should I use?
A multi-band survey or helical antenna with a ground plane.
Can I use it on a lawn mower robot?
Yes. RTK GNSS is widely used to guide robot lawn mowers.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

