Component guide · Beginner · 3 min read
NTC Thermistor Temperature Modules

4-Pin Analog and Digital, Keyestudio, Grove v1.2, HS-S35)
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
An NTC thermistor module puts a thermistor and its divider resistor on a small board, so you just connect power, ground and an analog pin. The 4-pin type adds an LM393 comparator and a trimmer for a digital over-temperature output. Grove v1.2, Keyestudio and HS-S35 boards give the analog signal only.
Key specs at a glance
- Thermistor
- 10k NTC, beta about 3950 to 4250
- Supply
- 3.3 to 5 V
- Outputs
- Analog (AO); digital (DO) on comparator boards
- Range
- About -20 to 100 degrees C
- Accuracy
- About plus or minus 1 to 1.5 degrees C
- Connector
- 2.54 mm header, Grove or PH2.0
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 14PIN NTC Thermistor Temperature Sensor Module – Digital/Analog Output₹42
Option 2NTC Thermistor Temperature Sensor Module – Digital Switch Output, 3.3V-5V₹32
Option 3Keyestudio Analog Temperature Sensor Detection Module for Arduino₹156
Option 4Seeed Studio Grove Temperature Sensor v1.2 – NTC Thermistor Module w/ Grove Cable₹339
Option 5HS-S35-L Thermal Sensor Module – Analog Output, 3-Pin 2.54mm Interface₹59
Option 6HS-S35A Thermal Sensor Module – Analog Output, 3.3V-5.5V₹58
What the NTC thermistor temperature modules is
NTC thermistor temperature modules put a thermistor, divider resistor and often a comparator on a small board, giving analog temperature and a digital threshold output.
On the 4-pin board the DO pin switches when the temperature crosses the trimmer setting. Turn the trimmer until the LED just changes at the temperature you want.
Note which way the divider is built: on some boards the reading rises with temperature, on others it falls. Heat the thermistor with your finger and watch.
NTC thermistor temperature modules pinout
The pins on the NTC thermistor temperature modules and what each one does.
| Pin | Function |
|---|---|
| VCC | 3.3 to 5 V |
| GND | Ground |
| AO / SIG | Analog output |
| DO | Digital threshold output (4-pin) |
- VCC
- 3.3 to 5 V
- GND
- Ground
- AO / SIG
- Analog output
- DO
- Digital threshold output (4-pin)
Wiring the NTC thermistor temperature modules
The Grove v1.2 sensor uses a 10 k NTC with beta 4275; use that value in code.
| NTC thermistor temperature modules pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5 V | 3.3 V |
| GND | GND | GND |
| AO | A0 | GPIO 34 |
| DO | D2 | GPIO 27 |
- VCC
- Arduino Uno:
- 5 V
- ESP32:
- 3.3 V
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- AO
- Arduino Uno:
- A0
- ESP32:
- GPIO 34
- DO
- Arduino Uno:
- D2
- ESP32:
- GPIO 27
Example code
If temperature goes the wrong way, your board has the thermistor on the top of the divider; swap the formula to r = R_FIXED * (1023.0 - a) / a.
const float R_FIXED = 10000.0; // onboard divider resistor
const float R0 = 10000.0, T0 = 298.15, BETA = 3950.0;
void setup() { Serial.begin(115200); }
void loop() {
int a = analogRead(A0); // probe from A0 to GND, R_FIXED from 5 V to A0
float r = R_FIXED * a / (1023.0 - a);
float tK = 1.0 / (1.0 / T0 + log(r / R0) / BETA);
Serial.print(tK - 273.15, 1); Serial.println(" C");
delay(1000);
}Setup and tuning
VCC, GND, AO to an analog pin and DO to a digital pin.
convert the AO voltage to temperature with the Beta equation and the module's resistor value.
turn the trimmer to set the DO trip point.
check whether DO goes HIGH or LOW when hot.
power from 3.3 V for ESP32 boards.
What you need
Shop this list10 of 11 found in our store · ₹1,340
Generic 4PIN NTC Thermistor Temperature Sensor Module – Digital/Analog Output: the part this guide covers4PIN NTC Thermistor Temperature Sensor Module – Digital/Analog Output₹42
Generic NTC Thermistor Temperature Sensor Module – Digital Switch Output, 3.3V-5V: another version this guide coversNTC Thermistor Temperature Sensor Module – Digital Switch Output, 3.3V-5V₹32
Keyestudio Analog Temperature Sensor Detection Module for Arduino: another version this guide coversKeyestudio Analog Temperature Sensor Detection Module for Arduino₹156
Seeed Studio Studio Grove Temperature Sensor v1.2 – NTC Thermistor Module w/ Grove Cable: another version this guide coversSeeed Studio Grove Temperature Sensor v1.2 – NTC Thermistor Module w/ Grove Cable₹339Closest match, check the specs
HS-S35-L Thermal Sensor Module – Analog Output, 3-Pin 2.54mm Interface: another version this guide coversHS-S35-L Thermal Sensor Module – Analog Output, 3-Pin 2.54mm Interface₹59
HS-S35A Thermal Sensor Module – Analog Output, 3.3V-5.5V: another version this guide coversHS-S35A Thermal Sensor Module – Analog Output, 3.3V-5.5V₹58
HS-S35P Thermal Sensor Module – Analog Output, 3.3V-5.5V: another version this guide coversHS-S35P Thermal Sensor Module – Analog Output, 3.3V-5.5V₹59- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Buzzer module 3.3-5 V: for an audible alarmBuzzer Module 3.3–5V₹27
16x2 LCD with I2C: to show readings on a character display16×2 LCD with I2C (RG1602A)₹179Closest match, check the specs
Alternatives and when to choose them
- NTC thermistor probes: waterproof probes.
- LM35 sensor: linear analog output.
- DS18B20: digital and more accurate.
Common mistakes to avoid
- Powering at 5 V into a 3.3 V ADC.
- Wrong divider orientation in code.
- Wrong B value.
- Expecting precision.
Frequently asked questions
How do I get temperature from AO?
Convert voltage to resistance, then use the Beta equation.
What does the trimmer do?
It sets the temperature at which the digital DO output switches.
Can I use it with ESP32?
Yes. Power the module from 3.3 V so its outputs stay safe for ESP32 pins.
Why is my reading reversed?
Some modules place the NTC on the other side of the divider.
How accurate is it?
About ±1 °C after calibration, good for rooms and simple alarms.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

