Component guide · Intermediate · 3 min read
PT100 Head-Type Probes, RTD Elements

Honeywell HEL-705, TE R-5156, Ni120), Protective Sleeves and Extension Cable
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A PT100 is a platinum resistor that reads 100 ohms at 0 degrees C and rises about 0.385 ohms per degree. Head-type probes put the element in a steel stem with a terminal head for industrial wiring. Bare RTD elements let you build your own, and stainless sleeves protect PT100 or DS18B20 probes in liquids. Read them with a MAX31865 or a PT100 transmitter.
Key specs at a glance
- Resistance
- 100 ohms at 0 degrees C (PT100), 1000 ohms (PT1000), 120 ohms (Ni120)
- Coefficient
- 0.00385 per degree C (platinum), 0.00672 (Ni120)
- Class
- Class B plus or minus (0.3 + 0.005 t) degrees C typical
- Range
- About -50 to 400 degrees C for probes
- Wiring
- 2, 3 or 4-wire
- Sleeves
- 6 x 30 mm and 6 x 50 mm stainless
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1PT100 Head Type RTD Temperature Probe, 6 mm₹464
Option 2Honeywell HEL-705-U-1-12-00 Platinum RTD Temperature Sensor, Ceramic Case with Leadwires, 1000 Ω at 0°C₹2,349
Option 3TE Connectivity MEAS STATOR R-5156 RTD Temperature Sensor, P100, ±0.5%, 0.050T, Rear-Exit Leads₹10,139
Option 4TE Connectivity MEAS STATOR R-8205 RTD Temperature Sensor, Nickel N120, 672 ppm/°C, ±0.5% Tolerance₹10,619
Option 5Stainless Steel Protective Sleeve 6x30mm – Compatible with PT100 & DS18B20 Temperature Probes₹20
Option 6Stainless Steel Temperature Sensor Protective Sleeve 6x50mm – Compatible with PT100 & DS18B20 Probes₹20
What the PT100 head probes, RTD elements, sleeves and cable is
Use 3-wire or 4-wire connections on long cables: in 2-wire mode the cable resistance adds directly to the reading (1 ohm is about 2.6 degrees C).
The nickel Ni120 RTD has a different curve; do not read it with PT100 code.
PT100 head probes, RTD elements, sleeves and cable pinout
The pins on the PT100 head probes, RTD elements, sleeves and cable and what each one does.
| Pin | Function |
|---|---|
| Red, red | One side of the element (3-wire uses both reds on one side) |
| White (or blue) | Other side |
| Head terminals | Numbered 1 to 4 |
- Red, red
- One side of the element (3-wire uses both reds on one side)
- White (or blue)
- Other side
- Head terminals
- Numbered 1 to 4
Wiring the PT100 head probes, RTD elements, sleeves and cable
Many MAX31865 boards need a solder jumper cut or bridged for 3-wire mode. Check the board's marking.
| PT100 head probes, RTD elements, sleeves and cable pin | Arduino Uno | ESP32 |
|---|---|---|
| RTD+ / F+ | MAX31865 RTD+ and F+ | MAX31865 RTD+ and F+ |
| RTD- / F- | MAX31865 RTD- and F- | MAX31865 RTD- and F- |
| MAX31865 CLK / SDO / SDI / CS | D13 / D12 / D11 / D10 | GPIO 18 / 19 / 23 / 5 |
| Jumpers | Set for 2, 3 or 4-wire | Same |
- RTD+ / F+
- Arduino Uno:
- MAX31865 RTD+ and F+
- ESP32:
- MAX31865 RTD+ and F+
- RTD- / F-
- Arduino Uno:
- MAX31865 RTD- and F-
- ESP32:
- MAX31865 RTD- and F-
- MAX31865 CLK / SDO / SDI / CS
- Arduino Uno:
- D13 / D12 / D11 / D10
- ESP32:
- GPIO 18 / 19 / 23 / 5
- Jumpers
- Arduino Uno:
- Set for 2, 3 or 4-wire
- ESP32:
- Same
Example code
A minimal sketch to check the part works.
#include <Adafruit_MAX31865.h>
Adafruit_MAX31865 rtd(10); // CS pin
const float RREF = 430.0; // reference resistor on PT100 boards
const float RNOMINAL = 100.0;
void setup() { Serial.begin(115200); rtd.begin(MAX31865_3WIRE); }
void loop() {
Serial.print(rtd.temperature(RNOMINAL, RREF), 2); Serial.println(" C");
if (rtd.readFault()) { Serial.println("RTD fault"); rtd.clearFault(); }
delay(1000);
}Setup and tuning
fill the sleeve with thermal paste for faster response.
use the extension cable with the same number of cores as the probe.
at room temperature a PT100 reads about 108 to 110 ohms on a meter.
What you need
Shop this list10 of 11 found in our store · ₹24,589
PT100 Head Type RTD Temperature Probe, 6 mm: the part this guide coversPT100 Head Type RTD Temperature Probe, 6 mm₹464
Honeywell HEL-705-U-1-12-00 Platinum RTD Temperature Sensor, Ceramic Case with Leadwires, 1000 Ω at 0°C: another version this guide coversHoneywell HEL-705-U-1-12-00 Platinum RTD Temperature Sensor, Ceramic Case with Leadwires, 1000 Ω at 0°C₹2,349
TE Connectivity MEAS STATOR R-5156 RTD Temperature Sensor, P100, ±0.5%, 0.050T, Rear-Exit Leads: another version this guide coversTE Connectivity MEAS STATOR R-5156 RTD Temperature Sensor, P100, ±0.5%, 0.050T, Rear-Exit Leads₹10,139
TE Connectivity MEAS STATOR R-8205 RTD Temperature Sensor, Nickel N120, 672 ppm/°C, ±0.5% Tolerance: another version this guide coversTE Connectivity MEAS STATOR R-8205 RTD Temperature Sensor, Nickel N120, 672 ppm/°C, ±0.5% Tolerance₹10,619
Generic Stainless Steel Protective Sleeve 6x30mm – Compatible with PT100 & DS18B20 Temperature Probes: another version this guide coversStainless Steel Protective Sleeve 6x30mm – Compatible with PT100 & DS18B20 Temperature Probes₹20
Generic Stainless Steel Temperature Sensor Protective Sleeve 6x50mm – Compatible with PT100 & DS18B20 Probes: another version this guide coversStainless Steel Temperature Sensor Protective Sleeve 6x50mm – Compatible with PT100 & DS18B20 Probes₹20
PT100 Sensor Extension Cable, 1 Metre: another version this guide coversPT100 Sensor Extension Cable, 1 Metre₹43
MAX31865 PT100/PT1000 RTD module: to read a PT100 probe from a microcontrollerMAX31865 PT100/PT1000 RTD Temperature Detector Module₹369Closest match, check the specs- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- PT100 RTD sensors: background and choosing.
- MAX31865 RTD module: the amplifier.
- K-type thermocouple probes: higher temperatures.
Common mistakes to avoid
- 2-wire on a long cable.
- Wrong RREF for PT100 vs PT1000.
- Reading a Ni120 as a PT100.
Frequently asked questions
2, 3 or 4-wire?
3-wire for most industrial use; 4-wire for best accuracy.
PT100 or PT1000?
PT1000 is less affected by cable resistance.
Can I check it with a meter?
Yes, about 100 ohms at 0 degrees C.
Do sleeves fit DS18B20?
Yes, 6 mm sleeves fit most probes.
Max temperature?
About 400 degrees C for typical probes.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

