Component guide · Beginner · 3 min read
PWM DC Motor Speed Controller with Knob

Wiring and Ratings
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A PWM DC motor speed controller sets the speed of a brushed DC motor, LED strip or fan with a knob, without any programming. It switches the supply on and off thousands of times a second with a MOSFET; the knob sets the on-time. Choose one whose voltage covers your supply and whose current rating is above the motor's running current, ideally its stall current.
Key specs at a glance
- Voltage
- 1.8 to 12 V (2 A knob module), 4.5 to 35 V (5 A), 12 to 24 V (10 A), 12 to 48 V (4-wire fan model)
- Current
- 2 A to 10 A continuous depending on model
- PWM
- Typically 1 to 25 kHz, 0 to 100 % duty
- Direction
- One direction only (no reverse)
- Control
- Potentiometer knob; some have on/off switch, display or temperature probe
- Fan models
- 4-wire PWM fan output and tacho (GB-DRFC-0118), temperature-based fan control (GB-DRFC-0119)
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1PWM DC Motor Speed Controller with Knob₹297
Option 2PWM DC Motor Speed Controller 10A₹184
Option 3PWM DC Motor Speed Controller Module (by Model)₹71
Option 4PWM DC Motor Speed Regulator 12V 24V 10A₹189
Option 52CH 4-Wire Digital PWM Motor/Fan Speed Controller 12-48V₹809
Option 6DC12V PWM DC Fan Speed Controller w/ Temp Probe & Alarm₹283
What the PWM DC motor speed controller is
These boards suit fans, pumps, conveyor motors, drills, LED strips and DC heaters where you just need a speed knob. They do not reverse the motor; add a DPDT switch (with the motor stopped) or use an H-bridge driver for that.
The USB fan controller sits between a USB port and a 12 V fan with a boost converter. The temperature models switch or vary the fan by a probe reading.
PWM DC motor speed controller pinout
The pins on the PWM DC motor speed controller and what each one does.
| Pin | Function |
|---|---|
| Power + / - | Supply input |
| Motor + / - | Motor or load output (the minus side is switched) |
| Knob | Speed, 0 to 100 % |
| Switch (some models) | On / off |
| PWM / tacho (fan model) | 4-wire fan PWM and speed outputs |
- Power + / -
- Supply input
- Motor + / -
- Motor or load output (the minus side is switched)
- Knob
- Speed, 0 to 100 %
- Switch (some models)
- On / off
- PWM / tacho (fan model)
- 4-wire fan PWM and speed outputs
Wiring the PWM DC motor speed controller
The motor minus terminal is not ground: never join it to the supply minus or to another circuit's ground, or the motor runs flat out. Add a fuse sized just above the motor's running current.
| PWM DC motor speed controller pin | Brushed DC motor | Fan or pump |
|---|---|---|
| Power + / - | Supply + / - (fused) | Supply + / - (fused) |
| Motor + / - | Motor terminals | Fan or pump terminals |
| Knob | Turn to set speed | Turn to set speed |
- Power + / -
- Brushed DC motor:
- Supply + / - (fused)
- Fan or pump:
- Supply + / - (fused)
- Motor + / -
- Brushed DC motor:
- Motor terminals
- Fan or pump:
- Fan or pump terminals
- Knob
- Brushed DC motor:
- Turn to set speed
- Fan or pump:
- Turn to set speed
Example code
To drive the speed from an Arduino instead, use a logic-level MOSFET module or an H-bridge driver; these knob modules have no PWM input except the 4-wire fan models.
1. Turn the knob fully anticlockwise (off).
2. Connect supply and motor, check polarity.
3. Power on and turn the knob slowly up.
4. If the motor hums but does not start at low settings, that is normal:
start at a higher setting, then turn down.Setup and tuning
pick a controller rated at least twice the motor's running current, or above its stall current for heavy starts.
the 10 A boards need airflow at full load.
most boards include a flyback diode; if not, add one across the motor.
long thin wires reduce torque; keep motor leads short and thick.
What you need
Shop this list10 of 11 found in our store · ₹2,535
PWM DC Motor Speed Controller with Knob: the part this guide coversPWM DC Motor Speed Controller with Knob₹297
PWM DC Motor Speed Controller 10A: another version this guide coversPWM DC Motor Speed Controller 10A₹184
PWM DC Motor Speed Controller Module (by Model): another version this guide coversPWM DC Motor Speed Controller Module (by Model)₹71
PWM DC Motor Speed Regulator 12V 24V 10A: another version this guide coversPWM DC Motor Speed Regulator 12V 24V 10A₹189
2CH 4-Wire Digital PWM Motor/Fan Speed Controller 12-48V: another version this guide covers2CH 4-Wire Digital PWM Motor/Fan Speed Controller 12-48V₹809
DC12V PWM DC Fan Speed Controller w/ Temp Probe & Alarm: another version this guide coversDC12V PWM DC Fan Speed Controller w/ Temp Probe & Alarm₹283
USB 12V DC Fan PWM Speed Controller Module: another version this guide coversUSB 12V DC Fan PWM Speed Controller Module₹70
SMPS power supply (12 V or 24 V): a bench or panel supply for the motorsEnclosed SMPS Power Supply₹257Closest match, check the specs
XL4015 5A buck converter: to step a higher supply down for the motorDC-DC Step-Down Buck Converter Power Supply Module 24V 12V 9V to 5V 5A 25W Replace LM2596S₹198Closest match, check the specs- Fuse holder: to protect the battery wiringFind this part
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- PWM explained: how duty cycle sets speed.
- DC motors: choosing and sizing motors.
- Cytron MD10C: add direction and microcontroller control.
Common mistakes to avoid
- Joining motor minus to supply minus and losing speed control.
- Choosing a controller rated at the motor's running current with no margin.
- Trying to reverse by swapping supply polarity.
- Using it on AC motors.
Frequently asked questions
Can it reverse the motor?
No. Use a DPDT switch with the motor stopped, or an H-bridge driver.
Will it work with a 12 V LED strip?
Yes, as a dimmer for single-colour strips.
Can it control an AC fan?
No. These are DC only; use an AC SCR or triac controller for AC.
Why does the motor buzz at low speed?
The PWM frequency is audible on some boards; it does no harm.
Can I control it from an Arduino?
Not the knob versions. Use a MOSFET module or motor driver instead.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



