Component guide · Advanced · 5 min read
Pyroelectric PIR Sensor Elements

D203S, D204B, Quad-Element, Excelitas, Murata, Panasonic) and Digital PIR Sensors (BS612, HM612)
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These are the bare infrared sensors inside motion detectors. Analog elements like the D203S and D204B give a tiny signal that needs an amplifier and comparator such as the BISS0001, or a ready PIR controller IC. Digital PIR sensors such as the Senba BS612, HM612 and the Panasonic EKMB have the amplifier built in and give a clean on or off output, so they connect straight to a microcontroller.
Key specs at a glance
- Elements
- Dual (D203S, D204B), quad (B2X2, G2X2, BQ604)
- Output
- Analog mV signal or digital (BS412, BS612, HM612, EKMB)
- Spectrum
- About 5 to 14 micrometres (body heat)
- Supply
- About 3 to 15 V for analog, 2.7 to 3.6 V or more for digital
- Package
- TO-5 metal can or SMD
- Lens
- Needs a Fresnel lens for range
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Senba D203S Analog Outdoor PIR Motion Sensor – TO-5 Package₹70
Option 2Senba D203B Dual PIR Sensor Alarm System Motion Detector – TO-5 Package₹82
Option 3Senba D204B Active PIR Motion Sensor with EMI Pyroelectric Infrared Detector₹51
Option 4Senba D204S 2-Element Pyroelectric Infrared Analog PIR Sensor₹62
Option 5Senba D205B Analog PIR Sensor – Wide-Angle Motion Detection₹135
Option 6Senba B2X2 Quad-Element Analog PIR Motion Sensor Module – TO-5 Package₹128
What the Pyroelectric PIR sensor elements and digital PIR chips is
Pyroelectric PIR sensor elements, such as the D203S and RE200B, are the bare dual-element IR detectors inside PIR motion sensors, used with a Fresnel lens and amplifier.
Dual elements cancel out slow changes like room warming, and quad elements reject pets and false triggers better.
Digital PIR sensors with delay, light and sensitivity set by resistors on pins (BS612, HM612) make a complete detector with just a Fresnel lens and a few parts.
Pyroelectric PIR sensor elements and digital PIR chips pinout
The pins on the Pyroelectric PIR sensor elements and digital PIR chips and what each one does.
| Pin | Function |
|---|---|
| D (drain) | Supply (analog elements) |
| S (source) | Signal via load resistor |
| G | Ground |
| Digital types | VDD, GND, REL / OUT, plus SENS, ONTIME, OEN pins |
- D (drain)
- Supply (analog elements)
- S (source)
- Signal via load resistor
- G
- Ground
- Digital types
- VDD, GND, REL / OUT, plus SENS, ONTIME, OEN pins
Wiring the Pyroelectric PIR sensor elements and digital PIR chips
Analog elements need a 47 k source resistor and about 0.5 to 1 Hz band-pass amplification of about 70 dB. Use the maker's reference circuit.
| Pyroelectric PIR sensor elements and digital PIR chips pin | Arduino Uno | ESP32 |
|---|---|---|
| Digital PIR VDD | 3.3 V | 3.3 V |
| Digital PIR GND | GND | GND |
| Digital PIR OUT | D2 | GPIO 27 |
| Analog element S | BISS0001 or op-amp input | Same |
- Digital PIR VDD
- Arduino Uno:
- 3.3 V
- ESP32:
- 3.3 V
- Digital PIR GND
- Arduino Uno:
- GND
- ESP32:
- GND
- Digital PIR OUT
- Arduino Uno:
- D2
- ESP32:
- GPIO 27
- Analog element S
- Arduino Uno:
- BISS0001 or op-amp input
- ESP32:
- Same
Example code
A minimal sketch to check the part works.
const int PIR = 2;
void setup() { Serial.begin(115200); pinMode(PIR, INPUT); delay(30000); }
void loop() {
static bool was = false;
bool now = digitalRead(PIR);
if (now && !was) Serial.println("Motion");
was = now;
delay(50);
}Setup and tuning
the element needs a load resistor (often 47 kΩ) on its source pin and a two-stage op-amp amplifier, or a BISS0001 chip.
fit a Fresnel lens to focus heat from the room onto the element.
typical drain voltage is 3 to 15 V.
let the circuit settle for 30 to 60 s after power-up.
avoid drafts and direct light on the element.
What you need
Shop this list20 of 20 found in our store · ₹5,084
Senba D203S Analog Outdoor PIR Motion Sensor – TO-5 Package: the part this guide coversSenba D203S Analog Outdoor PIR Motion Sensor – TO-5 Package₹70
Senba D203B Dual PIR Sensor Alarm System Motion Detector – TO-5 Package: another version this guide coversSenba D203B Dual PIR Sensor Alarm System Motion Detector – TO-5 Package₹82
Senba D204B Active PIR Motion Sensor with EMI Pyroelectric Infrared Detector: another version this guide coversSenba D204B Active PIR Motion Sensor with EMI Pyroelectric Infrared Detector₹51
Senba D204S 2-Element Pyroelectric Infrared Analog PIR Sensor: another version this guide coversSenba D204S 2-Element Pyroelectric Infrared Analog PIR Sensor₹62
Senba D205B Analog PIR Sensor – Wide-Angle Motion Detection: another version this guide coversSenba D205B Analog PIR Sensor – Wide-Angle Motion Detection₹135
Senba B2X2 Quad-Element Analog PIR Motion Sensor Module – TO-5 Package: another version this guide coversSenba B2X2 Quad-Element Analog PIR Motion Sensor Module – TO-5 Package₹128
Senba BQ604 Digital Quad PIR Motion Sensor – 4-Element, 6-Pin: another version this guide coversSenba BQ604 Digital Quad PIR Motion Sensor – 4-Element, 6-Pin₹94
Senba G2X2 Quad Four-element PIR Sensor Module – 3-15V DC, 120° Detection Angle: another version this guide coversSenba G2X2 Quad Four-element PIR Sensor Module – 3-15V DC, 120° Detection Angle₹91
Senba K222S Anti-EMI Anti-White Light PIR Sensor – Analog Signal Output: another version this guide coversSenba K222S Anti-EMI Anti-White Light PIR Sensor – Analog Signal Output₹78
Senba W216B Analog PIR Motion Sensor – Anti-EMI, 12m Range, 3-15V DC: another version this guide coversSenba W216B Analog PIR Motion Sensor – Anti-EMI, 12m Range, 3-15V DC₹108
Senba BS412 Smart Digital Human PIR Motion Sensor – IoT Security & Lighting Control: another version this guide coversSenba BS412 Smart Digital Human PIR Motion Sensor – IoT Security & Lighting Control₹153
Senba BS612 Digital PIR Motion Sensor – Schmitt Trigger Output: another version this guide coversSenba BS612 Digital PIR Motion Sensor – Schmitt Trigger Output₹107
Senba HM 612 Digital 6-Pin PIR Motion Sensor for Smart Light: another version this guide coversSenba HM 612 Digital 6-Pin PIR Motion Sensor for Smart Light₹128
Senba HM412 Digital Long Distance PIR Sensor, Delay Time Adjustable Sensor: another version this guide coversSenba HM412 Digital Long Distance PIR Sensor, Delay Time Adjustable Sensor₹112
Senba S18-L262B-2 Digital SMD PIR Motion Sensor: another version this guide coversSenba S18-L262B-2 Digital SMD PIR Motion Sensor₹85
Excelitas Technologies LHI 968 PIR Sensor, Pyroelectric, Dual Element, Intrusion Detector, TO-5 Metal Housing, 100° FOV: another version this guide coversExcelitas Technologies LHI 968 PIR Sensor, Pyroelectric, Dual Element, Intrusion Detector, TO-5 Metal Housing, 100° FOV₹989
Murata IRA-S210ST01 PIR Sensor, Lead Type, 45° FOV, IRA-S Series: another version this guide coversMurata IRA-S210ST01 PIR Sensor, Lead Type, 45° FOV, IRA-S Series₹319
Panasonic AMN31111 Passive Infrared Motion Sensor – TO-5 Package: another version this guide coversPanasonic AMN31111 Passive Infrared Motion Sensor – TO-5 Package₹757
Panasonic EKMB1306112K PIR Sensor, Digital, 17m Range, 4V, Black: another version this guide coversPanasonic EKMB1306112K PIR Sensor, Digital, 17m Range, 4V, Black₹1,439
Diodes Incorporated PT8A2648WEX PIR Sensor Light Switch SOIC-16 Human Body Sensor: another version this guide coversDiodes Incorporated PT8A2648WEX PIR Sensor Light Switch SOIC-16 Human Body Sensor₹96
Alternatives and when to choose them
- Mini PIR modules: finished boards.
- HC-SR501: BISS0001-based module.
- mmWave radar: presence detection.
Common mistakes to avoid
- Connecting the element straight to a GPIO.
- No Fresnel lens.
- Exposing the element to drafts.
- Noisy supply.
Frequently asked questions
Can I connect a D203S directly to a microcontroller?
No. Its signal is tiny, so use an amplifier circuit or a BISS0001 controller.
Why do I need a Fresnel lens?
The lens divides the room into zones so moving heat sources create pulses.
Why does my PIR circuit trigger randomly?
Drafts, sunlight or supply noise; shield it and filter the supply.
What is the BISS0001?
A PIR controller chip that amplifies and times the sensor output.
Why is the element dual?
Two elements cancel slow changes like room heating, detecting only movement.
Parts for this guide
- ₹70View
- ₹82View
- ₹51View
- ₹62View
- ₹135View
- ₹128View
- ₹94View
- ₹91View
- ₹78View
- ₹108View
- ₹153View
- ₹107View
- ₹128View
- ₹112View
- ₹85View
Excelitas Technologies LHI 968 PIR Sensor, Pyroelectric, Dual Element, Intrusion Detector, TO-5 Metal Housing, 100° FOV₹989View- ₹319View
- ₹757View
- ₹1,439View
- ₹96View
- ₹359View
- ₹389View
- ₹59View
- ₹177View
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




