Buying guide · Beginner · 3 min read
Raspberry Pi Cases and Cooling
Fans, Heatsinks and Temperature Limits
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Raspberry Pi 4 and 5 start slowing down (thermal throttling) at about 80 degrees C. A Pi 4 is fine in a vented case with heatsinks; a Pi 5 under load needs the official Active Cooler or a case with a fan. Pick a case made for your exact model, check that it exposes the ports and GPIO you use, and measure temperature with vcgencmd measure_temp.
Key specs at a glance
- Throttling starts
- About 80 °C CPU temperature
- Hard limit
- 85 °C, where clock speed drops further
- Pi 5 cooler
- Official Active Cooler: aluminium heatsink with fan on the 4-pin fan header
- Pi 4 cooling
- Passive heatsinks work for light use; a fan for sustained load
- Case materials
- ABS plastic, aluminium, acrylic
- Mounting
- Four M2.5 holes, 58 x 49 mm pattern
Why cooling matters
The Raspberry Pi 5's quad-core CPU gets hot enough under load to throttle its clock speed within a minute or two without a heatsink. Throttling does not damage the board, but it makes video, compiles and AI jobs slow and unpredictable. The Pi 4 runs cooler but still throttles in sealed plastic cases.
Check your temperature with:
vcgencmd measure_temp
vcgencmd get_throttled
# 0x0 means no throttling or under-voltage has happened since bootPassive vs active cooling
The options run from silent to very effective:
| Option | Noise | Cooling | Best with |
|---|---|---|---|
| Bare board | Silent | Poor under load | Light tasks on Pi 3 or Zero |
| Stick-on aluminium heatsinks | Silent | Fair | Pi 4 for general use |
| Passive aluminium case (heat-spreading) | Silent | Good for Pi 4, fair for Pi 5 | Fanless media players and servers |
| Fan + heatsink (Active Cooler) | Low hum | Very good | Pi 5 under load, overclocking |
| Tower cooler / large fan case | Quiet | Best | Pi 5 with NVMe or 24/7 compiles |
- Bare board
- Noise:
- Silent
- Cooling:
- Poor under load
- Best with:
- Light tasks on Pi 3 or Zero
- Stick-on aluminium heatsinks
- Noise:
- Silent
- Cooling:
- Fair
- Best with:
- Pi 4 for general use
- Passive aluminium case (heat-spreading)
- Noise:
- Silent
- Cooling:
- Good for Pi 4, fair for Pi 5
- Best with:
- Fanless media players and servers
- Fan + heatsink (Active Cooler)
- Noise:
- Low hum
- Cooling:
- Very good
- Best with:
- Pi 5 under load, overclocking
- Tower cooler / large fan case
- Noise:
- Quiet
- Cooling:
- Best
- Best with:
- Pi 5 with NVMe or 24/7 compiles
Choosing a case
The Pi 4 and Pi 5 share the same board outline, but the Pi 5 adds a fan header, power button and PCIe connector. A Pi 4 case may block those.
Make sure openings line up with the ports and the GPIO header you need. Some cases cover GPIO completely.
A case that covers the whole board with plastic traps heat. Look for vents, a fan or a metal body.
Some cases hold an NVMe drive or a SATA SSD, which also adds power draw. Check the supply rating.
DIN-rail, VESA and wall-mount cases suit kiosks and home servers.
Fitting a cooler
The official Active Cooler pushes onto two spring-loaded clips and plugs its fan lead into the 4-pin fan connector on the board. Use a thermal pad (supplied) between the heatsink and the chip, and press until both clips click. Stick-on heatsinks go on the CPU, RAM and USB controller; peel the film and press without sliding them.
Try it: Power supply sizing calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Installing a fan case on a Pi 5 and leaving the fan header unplugged.
- Putting a Pi 5 into a Pi 4 case and blocking the new connectors.
- Sticking heatsinks on while the board is powered.
- Running NVMe in a sealed case with no airflow.
- Ignoring a lightning bolt icon, which signals under-voltage.
Frequently asked questions
Do I need a fan on a Raspberry Pi 4?
Not for light use. For video, servers or overclocking, a fan or a good heatsink case keeps it below 70 °C.
Does the Pi 5 need the Active Cooler?
It is strongly recommended under load. It is optional for light desktop use.
How hot is too hot?
Above 80 °C the Pi slows down. Keep it under 70 °C for headroom.
Can I overclock with a passive case?
Only lightly. Overclocking needs active cooling and a strong power supply.
Are metal cases worth it?
Yes for fanless builds, because the case acts as a heatsink. Check that antennas still get a signal.
Will a case affect Wi-Fi?
Metal cases can block Wi-Fi and Bluetooth. Use an external antenna or a plastic top.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 3 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
- Raspberry Pi documentation: hardware and thermal specification
- Raspberry Pi Active Cooler product brief
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




