Component guide · Beginner · 4 min read
Raspberry Pi PoE HATs

Official PoE+ HAT, Waveshare PoE HAT E to J, Geekworm Pi 5 PoE and NVMe plus PoE Combos (52Pi P33, Elecrow, X1012)
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A PoE HAT takes power from the Ethernet cable, so a Raspberry Pi needs only one cable for both network and power. That is ideal for cameras, ceiling-mounted sensors and server racks. The Pi 3B+ and Pi 4 use the official PoE+ HAT or Waveshare (E); the Pi 5 needs a 5A board such as Waveshare (G), (H), (J) or Geekworm. Combo boards add an NVMe slot too.
Key specs at a glance
- Standard
- 802.3af (PoE, 15W) or 802.3at (PoE+, 30W)
- Output
- 5V 2.5A to 5V 5A
- Pins used
- 4 PoE pins next to the GPIO header
- Cooling
- Fan or heatsink on most boards
- Pi models
- 3B+, 4B, 5 and CM5 (check each board)
- Combo
- PoE plus M.2 NVMe on 52Pi P33, Elecrow, X1012, Waveshare
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Official Raspberry Pi PoE+ HAT for Pi 3B+/Pi 4₹2,359
Option 2Raspberry Pi 3B+ PoE HAT₹2,499
Option 3Geekworm Raspberry Pi 5 PoE HAT 802.3af/at (USB-C)₹2,659
Option 4Waveshare PoE HAT (E) for Raspberry Pi 3B+/4B₹1,459
Option 5Waveshare PoE HAT (F) for Raspberry Pi 5 w/ Fan & Heatsink₹2,199
Option 6Waveshare PoE HAT (G) for Raspberry Pi 5, 5V 5A Output₹1,619
What the Raspberry Pi PoE and PoE+ HATs is
Raspberry Pi PoE HATs take power from a Power over Ethernet switch through the network cable, so a Pi needs only one cable for both data and power.
You need a PoE switch or injector on the other end; a normal switch does not send power. For a Pi 5 with an SSD, choose PoE+ (802.3at) so the board can supply 5A.
The Pi 3B+ PoE HAT does not fit the Pi 5, which moved its PoE pins.
Raspberry Pi PoE and PoE+ HATs pinout
The pins on the Raspberry Pi PoE and PoE+ HATs and what each one does.
| Pin | Function |
|---|---|
| PoE header (4-pin) | Carries the raw PoE voltage from the RJ45 jack |
| GPIO 5V and GND | Where the HAT feeds 5V back into the Pi |
| Fan | Controlled by the Pi over I2C or GPIO |
| M.2 / FFC | Only on NVMe combo boards |
- PoE header (4-pin)
- Carries the raw PoE voltage from the RJ45 jack
- GPIO 5V and GND
- Where the HAT feeds 5V back into the Pi
- Fan
- Controlled by the Pi over I2C or GPIO
- M.2 / FFC
- Only on NVMe combo boards
Wiring the Raspberry Pi PoE and PoE+ HATs
Fit the standoffs, then press the HAT straight down onto both the GPIO and PoE pins. Never power the Pi from USB-C and PoE at the same time unless the board says it is safe.
| Raspberry Pi PoE and PoE+ HATs pin | Raspberry Pi 4 | Raspberry Pi 5 |
|---|---|---|
| PoE pins | 4-pin header beside the GPIO | 4-pin header (Pi 5 position) |
| GPIO | Through the 40-pin header | Through the 40-pin header |
| Network | Cable from a PoE switch | Cable from a PoE+ switch |
- PoE pins
- Raspberry Pi 4:
- 4-pin header beside the GPIO
- Raspberry Pi 5:
- 4-pin header (Pi 5 position)
- GPIO
- Raspberry Pi 4:
- Through the 40-pin header
- Raspberry Pi 5:
- Through the 40-pin header
- Network
- Raspberry Pi 4:
- Cable from a PoE switch
- Raspberry Pi 5:
- Cable from a PoE+ switch
Example code
Waveshare and Geekworm boards with their own fan controller come with a small script or overlay; follow their wiki.
# Official PoE+ HAT on a Pi 4: fan speeds by temperature (millidegrees)
sudo tee -a /boot/firmware/config.txt <<'EOF'
dtparam=poe_fan_temp0=55000
dtparam=poe_fan_temp1=60000
dtparam=poe_fan_temp2=65000
dtparam=poe_fan_temp3=70000
EOF
sudo reboot
vcgencmd measure_tempSetup and tuning
use an 802.3af or 802.3at (PoE+) switch or injector; passive PoE is not compatible.
use the PoE+ HAT for Pi 4 and the PoE+ HAT for Pi 5 (with matching header).
PoE+ gives up to about 25 W; heavy USB loads may need more.
the HAT fan cools the Pi; keep it unobstructed.
use the supplied stand-offs to avoid shorts.
What you need
Shop this list15 of 16 found in our store · ₹52,008
Official Raspberry Pi PoE+ HAT for Pi 3B+/Pi 4: the part this guide coversOfficial Raspberry Pi PoE+ HAT for Pi 3B+/Pi 4₹2,359
Raspberry Pi 3B+ PoE HAT: another version this guide coversRaspberry Pi 3B+ PoE HAT₹2,499
Geekworm Raspberry Pi 5 PoE HAT 802.3af/at (USB-C): another version this guide coversGeekworm Raspberry Pi 5 PoE HAT 802.3af/at (USB-C)₹2,659
Waveshare PoE HAT (E) for Raspberry Pi 3B+/4B: another version this guide coversWaveshare PoE HAT (E) for Raspberry Pi 3B+/4B₹1,459
Waveshare PoE HAT (F) for Raspberry Pi 5 w/ Fan & Heatsink: another version this guide coversWaveshare PoE HAT (F) for Raspberry Pi 5 w/ Fan & Heatsink₹2,199
Waveshare PoE HAT (G) for Raspberry Pi 5, 5V 5A Output: another version this guide coversWaveshare PoE HAT (G) for Raspberry Pi 5, 5V 5A Output₹1,619
Waveshare PoE HAT (H) for Raspberry Pi 5 / CM5, 5V 5A Output: another version this guide coversWaveshare PoE HAT (H) for Raspberry Pi 5 / CM5, 5V 5A Output₹2,429
Waveshare PoE HAT (J) for Raspberry Pi 5 / CM5: another version this guide coversWaveshare PoE HAT (J) for Raspberry Pi 5 / CM5₹2,050
52Pi P33 M.2 NVMe PoE+ HAT for Raspberry Pi 5: another version this guide covers52Pi P33 M.2 NVMe PoE+ HAT for Raspberry Pi 5₹4,149
Elecrow Pi Power M.2 NVMe & PoE+ HAT for Raspberry Pi 5: another version this guide coversElecrow Pi Power M.2 NVMe & PoE+ HAT for Raspberry Pi 5₹1,549
Geekworm X1012 PCIe NVMe+POE Shield for Raspberry Pi 5: another version this guide coversGeekworm X1012 PCIe NVMe+POE Shield for Raspberry Pi 5₹4,496
Waveshare PCIe to M.2 NVMe SSD & PoE HAT for Raspberry Pi 5: another version this guide coversWaveshare PCIe to M.2 NVMe SSD & PoE HAT for Raspberry Pi 5₹2,559
Raspberry Pi 5 (4 GB): the board with the PCIe connectorRaspberry Pi Compute Module 5 IO Board₹3,159Closest match, check the specs
Raspberry Pi 4 Model B (4 GB): for USB and GPIO boardsRaspberry Pi 4 Model B with 4GB RAM₹11,461Closest match, check the specs- PUSR industrial PoE switch: supplies power over the Ethernet cableFind this part
WD Green SN350 NVMe SSD: an M.2 NVMe drive to fitWD Green SN350 NVMe SSD₹7,362
Alternatives and when to choose them
- Pi power supplies: USB-C options.
- UPS HATs: battery back-up.
- NVMe SSD HATs: storage only.
Common mistakes to avoid
- Using passive PoE.
- Wrong HAT for the Pi model.
- Overloading USB ports.
- Missing stand-offs.
Frequently asked questions
Can any Ethernet switch power my Pi?
No. The switch must support 802.3af or 802.3at PoE.
Is passive PoE compatible?
No. Passive 24 V PoE can damage the HAT.
How much power does PoE+ give?
About 25 W at the HAT, enough for the Pi and light USB use.
Why is my PoE HAT fan noisy?
Raise the fan temperature thresholds in config.txt so it runs less often.
Will the Pi 4 PoE HAT fit a Pi 5?
No. Use the PoE+ HAT made for Pi 5.
Parts for this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


