Component guide · Intermediate · 5 min read
Raspberry Pi 5 NVMe SSD HATs

Official M.2 HAT+, Geekworm X1000 to X1015, Pineboards HatDrive, Waveshare, Seeed, 52Pi and Elecrow
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These boards connect one M.2 NVMe SSD to the Raspberry Pi 5's PCIe connector. An SSD is many times faster and more reliable than a microSD card, and the Pi 5 can boot from it. Top HATs sit above the Pi; bottom boards sit underneath so the active cooler and other HATs still fit. Pick by SSD length (2230 to 2280) and where you want it to sit.
Key specs at a glance
- Interface
- PCIe 2.0 x1 (Gen 3 possible) through a 16-pin FFC
- SSD sizes
- 2230, 2242, 2260 and 2280 depending on the board
- Key
- M key NVMe (not SATA M.2)
- Speed
- About 450 MB/s Gen 2, up to about 900 MB/s Gen 3
- Position
- Top HAT or bottom board
- Boot
- Pi 5 boots from NVMe after a bootloader update
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Official Raspberry Pi M.2 HAT+ Compact₹1,433
Option 2Raspberry Pi M.2 HAT+ M Key₹1,609
Option 3Geekworm X1000 PCIe to M.2 NVMe SSD HAT for Raspberry Pi 5₹1,439
Option 4Geekworm X1001 PCIe to M.2 NVMe SSD for Raspberry Pi 5₹1,349
Option 5Geekworm X1002 NVMe M.2 SSD PCIe Bottom Board for Pi 5₹1,659
Option 6Geekworm X1003 PCIe to M.2 NVMe SSD Top Hat for Raspberry Pi 5₹1,189
What the Raspberry Pi 5 single NVMe SSD HATs and bottom boards is
Pi 5 NVMe SSD HATs, such as the official M.2 HAT+ and Pimoroni NVMe Base, connect an M.2 NVMe SSD to the Raspberry Pi 5's PCIe port for fast storage and booting.
The official M.2 HAT+ (standard and compact) follows the HAT+ standard and is detected automatically. Geekworm X1000 to X1003 and X1015, Pineboards HatDrive Top and Lite, Waveshare and Seeed HATs are similar top boards. The X1002, 52Pi RS-P11 and Elecrow board mount underneath.
Only NVMe drives work. M.2 SATA SSDs look the same but will not be detected. A few SSD controllers (some Phison and older WD) are fussy on the Pi; check the board maker's list.
Raspberry Pi 5 single NVMe SSD HATs and bottom boards pinout
The pins on the Raspberry Pi 5 single NVMe SSD HATs and bottom boards and what each one does.
| Pin | Function |
|---|---|
| PCIe FFC (16-pin) | One PCIe 2.0 x1 lane from the Pi 5 to the board, through a short flat cable |
| M.2 slot | M key for NVMe SSDs or AI accelerators; E key for Wi-Fi cards |
| Power pogo pins / GPIO | Some boards take 5V from the GPIO header or pogo pins, others from the FFC |
| Status LED | Shows power and drive activity on most boards |
- PCIe FFC (16-pin)
- One PCIe 2.0 x1 lane from the Pi 5 to the board, through a short flat cable
- M.2 slot
- M key for NVMe SSDs or AI accelerators; E key for Wi-Fi cards
- Power pogo pins / GPIO
- Some boards take 5V from the GPIO header or pogo pins, others from the FFC
- Status LED
- Shows power and drive activity on most boards
Wiring the Raspberry Pi 5 single NVMe SSD HATs and bottom boards
Power off first. Lift the latch on the Pi 5 PCIe connector, push the FFC in fully with the contacts facing the pins, close the latch, then do the same on the board. A loose or reversed cable is the most common reason a drive is not detected.
| Raspberry Pi 5 single NVMe SSD HATs and bottom boards pin | Connection | Note |
|---|---|---|
| FFC cable | Pi 5 PCIe connector to the board's FFC socket | Contacts face the connector pins on both ends |
| Power | From the FFC or the GPIO header | Use the 27W supply |
| Mounting | Standoffs on top (HAT) or under the Pi (bottom board) | Check the cooler fits |
- FFC cable
- Connection:
- Pi 5 PCIe connector to the board's FFC socket
- Note:
- Contacts face the connector pins on both ends
- Power
- Connection:
- From the FFC or the GPIO header
- Note:
- Use the 27W supply
- Mounting
- Connection:
- Standoffs on top (HAT) or under the Pi (bottom board)
- Note:
- Check the cooler fits
Example code
Update the bootloader first with sudo rpi-eeprom-update -a. If lsblk shows no nvme device, reseat the FFC and add dtparam=pciex1 to config.txt on boards without an EEPROM.
# 1. Is the drive seen?
lsblk # look for nvme0n1
lspci # shows the NVMe controller
# 2. Optional: PCIe Gen 3 (faster, not officially certified)
echo "dtparam=pciex1_gen=3" | sudo tee -a /boot/firmware/config.txt
# 3. Copy the SD card to the SSD (or use Raspberry Pi Imager)
sudo apt install rpi-clone
sudo rpi-clone nvme0n1
# 4. Boot from NVMe first
sudo rpi-eeprom-config --edit # set BOOT_ORDER=0xf416
sudo rebootSetup and tuning
check which M.2 lengths fit (2230, 2242, 2280) on your HAT.
fit the FPC cable to the Pi 5 PCIe port, contacts the right way.
update the bootloader and set NVMe first in the boot order.
add dtparam=pciex1_gen=3 in config.txt for more speed; it is not officially certified.
some SSDs with certain controllers have issues; check the HAT's tested list.
What you need
Shop this list20 of 20 found in our store · ₹35,442
Official Raspberry Pi M.2 HAT+ Compact: the part this guide coversOfficial Raspberry Pi M.2 HAT+ Compact₹1,433
Raspberry Pi M.2 HAT+ M Key: another version this guide coversRaspberry Pi M.2 HAT+ M Key₹1,609
Geekworm X1000 PCIe to M.2 NVMe SSD HAT for Raspberry Pi 5: another version this guide coversGeekworm X1000 PCIe to M.2 NVMe SSD HAT for Raspberry Pi 5₹1,439
Geekworm X1001 PCIe to M.2 NVMe SSD for Raspberry Pi 5: another version this guide coversGeekworm X1001 PCIe to M.2 NVMe SSD for Raspberry Pi 5₹1,349
Geekworm X1002 NVMe M.2 SSD PCIe Bottom Board for Pi 5: another version this guide coversGeekworm X1002 NVMe M.2 SSD PCIe Bottom Board for Pi 5₹1,659
Geekworm X1003 PCIe to M.2 NVMe SSD Top Hat for Raspberry Pi 5: another version this guide coversGeekworm X1003 PCIe to M.2 NVMe SSD Top Hat for Raspberry Pi 5₹1,189
Geekworm X1015 PCIe to M.2 NVMe SSD HAT for Raspberry Pi 5: another version this guide coversGeekworm X1015 PCIe to M.2 NVMe SSD HAT for Raspberry Pi 5₹1,569
Geekworm M901 PCIe to M.2 NVMe SSD PIP for Raspberry Pi 5: another version this guide coversGeekworm M901 PCIe to M.2 NVMe SSD PIP for Raspberry Pi 5₹979
52Pi RS-P11 PCIe NVMe Expansion Board for Raspberry Pi 5: another version this guide covers52Pi RS-P11 PCIe NVMe Expansion Board for Raspberry Pi 5₹2,459
Elecrow PCIe to M.2 NVMe SSD Board for Raspberry Pi 5: another version this guide coversElecrow PCIe to M.2 NVMe SSD Board for Raspberry Pi 5₹943
Waveshare PCIe to M.2 NVMe HAT for Raspberry Pi 5: another version this guide coversWaveshare PCIe to M.2 NVMe HAT for Raspberry Pi 5₹559
Waveshare PCIe to M.2 NVMe SSD Adapter HAT+ for Raspberry Pi 5: another version this guide coversWaveshare PCIe to M.2 NVMe SSD Adapter HAT+ for Raspberry Pi 5₹869
Pineboards HatDrive! Top (NVMe 2230/2242) for Raspberry Pi 5: another version this guide coversPineboards HatDrive! Top (NVMe 2230/2242) for Raspberry Pi 5₹2,079
Pineboards HatDrive! Top Lite for Raspberry Pi 5 (NVMe 2230/2242): another version this guide coversPineboards HatDrive! Top Lite for Raspberry Pi 5 (NVMe 2230/2242)₹1,789
Seeed Studio Studio PCIe to M.2 HAT for Raspberry Pi 5 NVMe: another version this guide coversSeeed Studio PCIe to M.2 HAT for Raspberry Pi 5 NVMe₹819Closest match, check the specs
Argon Industria PCIe M.2 Single NVMe Board: another version this guide coversArgon Industria PCIe M.2 Single NVMe Board₹1,259
Waveshare PCIe to M.2 HAT for Raspberry Pi w/ I2S Audio: another version this guide coversWaveshare PCIe to M.2 HAT for Raspberry Pi w/ I2S Audio₹1,600
Raspberry Pi 5 (4 GB): the board with the PCIe connectorRaspberry Pi Compute Module 5 IO Board₹3,159Closest match, check the specs
WD Green SN350 NVMe SSD: an M.2 NVMe drive to fitWD Green SN350 NVMe SSD₹7,362
Official 27W USB-C power supply for Pi 5: enough current for the Pi plus an SSDOfficial 27W USB-C PD Power Supply for Raspberry Pi 5 – IN Plug₹1,319Closest match, check the specs
Alternatives and when to choose them
- Dual and quad NVMe boards: more than one drive.
- PoE and NVMe combo HATs: power and storage on one board.
- NVMe and PCIe overview: how PCIe works on the Pi 5.
Common mistakes to avoid
- Choosing a too-long SSD.
- Reversing the FPC cable.
- Forgetting the bootloader update.
- Using known-incompatible SSDs.
Frequently asked questions
How do I boot a Pi 5 from NVMe?
Flash Raspberry Pi OS to the SSD, update the bootloader and set NVMe first.
Which SSD sizes fit?
Most HATs take 2230 and 2242; some fit 2280.
Can I enable PCIe Gen 3?
Yes. Add dtparam=pciex1_gen=3 to config.txt; it roughly doubles speed but is not officially certified.
Why is my SSD not detected?
The cable is reversed or the SSD is incompatible.
Is NVMe faster than SD cards?
Yes. NVMe is many times faster than microSD, so the Pi boots and opens apps much quicker.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


