Component guide · Advanced · 5 min read
Dual and Quad NVMe Boards for Raspberry Pi 5

Geekworm X1004 and X1011, 52Pi N16 and N21, HatDrive Dual, Seeed, Waveshare and Argon ONE V5
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Pi 5 has one PCIe lane. These boards add a PCIe switch chip (usually ASM1182e or ASM2806) that shares that lane between two or four M.2 slots, so you can fit several SSDs, or an SSD plus a Hailo AI module. Total speed stays at one lane, so they suit a small NAS or mixed storage and AI, not maximum per-drive speed.
Key specs at a glance
- Slots
- 2 or 4 M.2 M key
- Switch
- ASMedia PCIe 2.0 or 3.0 packet switch
- Shared bandwidth
- About 450 to 900 MB/s total
- SSD sizes
- 2230 to 2280
- Extra power
- DC barrel or 5V input on quad boards
- Uses
- NAS, RAID 1, SSD plus AI accelerator
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Geekworm X1004 Dual 2280 NVMe SSD Shield for Pi 5₹4,609
Option 2Geekworm X1011 PCIe to 4x M.2 NVMe SSD Board for Raspberry Pi 5₹6,319
Option 3Geekworm X1010 PCIe x4 Expansion Board for Raspberry Pi 5₹3,389
Option 452Pi N16 Quad NVMe Expansion Board for Raspberry Pi 5₹5,491
Option 552Pi N21 Dual NVMe Base for Raspberry Pi 5₹4,299
Option 6Pineboards HatDrive! Dual 2xNVMe PCIe Gen3 for Raspberry Pi 5₹4,879
What the Dual and quad NVMe and PCIe switch boards for Raspberry Pi 5 is
Pi 5 multi-NVMe and PCIe switch boards use a PCIe switch chip to connect two or more NVMe SSDs, or an SSD plus another PCIe device, to the Raspberry Pi 5's single PCIe lane.
Dual boards (Geekworm X1004, 52Pi N21, HatDrive Dual, Seeed, Waveshare) run from the Pi's 5V. Quad boards (X1011, 52Pi N16, Argon ONE V5) need their own power input because four SSDs can pull more than the Pi can give.
The Waveshare FFC adapters and the 4-port Gen 2 expander split the PCIe lane for custom builds.
Dual and quad NVMe and PCIe switch boards for Raspberry Pi 5 pinout
The pins on the Dual and quad NVMe and PCIe switch boards for Raspberry Pi 5 and what each one does.
| Pin | Function |
|---|---|
| PCIe FFC (16-pin) | One PCIe 2.0 x1 lane from the Pi 5 to the board, through a short flat cable |
| M.2 slot | M key for NVMe SSDs or AI accelerators; E key for Wi-Fi cards |
| Power pogo pins / GPIO | Some boards take 5V from the GPIO header or pogo pins, others from the FFC |
| Status LED | Shows power and drive activity on most boards |
| DC input | Separate 5V or 12V supply on quad boards |
- PCIe FFC (16-pin)
- One PCIe 2.0 x1 lane from the Pi 5 to the board, through a short flat cable
- M.2 slot
- M key for NVMe SSDs or AI accelerators; E key for Wi-Fi cards
- Power pogo pins / GPIO
- Some boards take 5V from the GPIO header or pogo pins, others from the FFC
- Status LED
- Shows power and drive activity on most boards
- DC input
- Separate 5V or 12V supply on quad boards
Wiring the Dual and quad NVMe and PCIe switch boards for Raspberry Pi 5
Power off first. Lift the latch on the Pi 5 PCIe connector, push the FFC in fully with the contacts facing the pins, close the latch, then do the same on the board. A loose or reversed cable is the most common reason a drive is not detected.
| Dual and quad NVMe and PCIe switch boards for Raspberry Pi 5 pin | Connection | Note |
|---|---|---|
| FFC cable | Pi 5 PCIe connector to the board's FFC socket | Contacts face the connector pins on both ends |
| Power | From the FFC or the GPIO header | Use the 27W supply |
| Mounting | Standoffs on top (HAT) or under the Pi (bottom board) | Check the cooler fits |
- FFC cable
- Connection:
- Pi 5 PCIe connector to the board's FFC socket
- Note:
- Contacts face the connector pins on both ends
- Power
- Connection:
- From the FFC or the GPIO header
- Note:
- Use the 27W supply
- Mounting
- Connection:
- Standoffs on top (HAT) or under the Pi (bottom board)
- Note:
- Check the cooler fits
Example code
Leave PCIe at Gen 2 if a switch board is unstable at Gen 3. Booting from a drive behind a switch works on recent bootloaders.
lsblk # nvme0n1 and nvme1n1
sudo apt install mdadm
sudo mdadm --create /dev/md0 --level=1 --raid-devices=2 /dev/nvme0n1 /dev/nvme1n1
sudo mkfs.ext4 /dev/md0
sudo mkdir -p /mnt/raid && sudo mount /dev/md0 /mnt/raid
sudo mdadm --detail --scan | sudo tee -a /etc/mdadm/mdadm.confSetup and tuning
fit the flat FPC cable between the Pi 5 PCIe port and the board, contacts facing the right way.
all devices share one PCIe 2.0 lane (about 500 MB/s, or about 1 GB/s at Gen 3 if forced).
set the boot order with rpi-eeprom-config; booting from a drive behind a switch may need a recent bootloader.
two SSDs can draw more than the Pi supplies; use the official 27 W supply or board power input.
use mdadm or ZFS in software for mirroring.
What you need
Shop this list19 of 19 found in our store · ₹73,281
Geekworm X1004 Dual 2280 NVMe SSD Shield for Pi 5: the part this guide coversGeekworm X1004 Dual 2280 NVMe SSD Shield for Pi 5₹4,609
Geekworm X1011 PCIe to 4x M.2 NVMe SSD Board for Raspberry Pi 5: another version this guide coversGeekworm X1011 PCIe to 4x M.2 NVMe SSD Board for Raspberry Pi 5₹6,319
Geekworm X1010 PCIe x4 Expansion Board for Raspberry Pi 5: another version this guide coversGeekworm X1010 PCIe x4 Expansion Board for Raspberry Pi 5₹3,389
52Pi N16 Quad NVMe Expansion Board for Raspberry Pi 5: another version this guide covers52Pi N16 Quad NVMe Expansion Board for Raspberry Pi 5₹5,491
52Pi N21 Dual NVMe Base for Raspberry Pi 5: another version this guide covers52Pi N21 Dual NVMe Base for Raspberry Pi 5₹4,299
Pineboards HatDrive! Dual 2xNVMe PCIe Gen3 for Raspberry Pi 5: another version this guide coversPineboards HatDrive! Dual 2xNVMe PCIe Gen3 for Raspberry Pi 5₹4,879
Seeed Studio Studio Dual M.2 PCIe 3.0 Switch HAT for Raspberry Pi 5: another version this guide coversSeeed Studio Dual M.2 PCIe 3.0 Switch HAT for Raspberry Pi 5₹5,349
Seeed Studio Studio Dual M.2 PCIe HAT for Raspberry Pi 5 NVMe/AI: another version this guide coversSeeed Studio Dual M.2 PCIe 3.0 Switch HAT for Raspberry Pi 5₹5,349Closest match, check the specs
Waveshare PCIe to Dual M.2 NVMe HAT for Raspberry Pi 5: another version this guide coversWaveshare PCIe to Dual M.2 NVMe HAT+ for Raspberry Pi 5₹1,549
Waveshare PCIe to Dual M.2 NVMe HAT+ for Raspberry Pi 5: another version this guide coversWaveshare PCIe to Dual M.2 NVMe HAT+ for Raspberry Pi 5₹1,549
Argon ONE V5 Quad M.2 NVMe Expansion Board Gen 2.0: another version this guide coversArgon ONE V5 Quad M.2 NVMe Expansion Board Gen 2.0₹3,969
Argon ONE V5 Quad M.2 NVMe Expansion Board Gen 3.0: another version this guide coversArgon ONE V5 Quad M.2 NVMe Expansion Board Gen 3.0₹8,357
Waveshare 4-Ch PCIe Gen 2 x1 Expander Driver-Free: another version this guide coversWaveshare 4-Ch PCIe Gen 2 x1 Expander Driver-Free₹1,829
Waveshare 2-Ch PCIe FFC Adapter Board for Raspberry Pi 5: another version this guide coversWaveshare 2-Ch PCIe FFC Adapter Board for Raspberry Pi 5₹1,509
Waveshare 4-Ch PCIe FFC Adapter Board for Raspberry Pi 5: another version this guide coversWaveshare 4-Ch PCIe FFC Adapter Board for Raspberry Pi 5₹2,429
Raspberry Pi 5 (4 GB): the board with the PCIe connectorRaspberry Pi Compute Module 5 IO Board₹3,159Closest match, check the specs
WD Green SN350 NVMe SSD: an M.2 NVMe drive to fitWD Green SN350 NVMe SSD₹7,362
Official 27W USB-C power supply for Pi 5: enough current for the Pi plus an SSDOfficial 27W USB-C PD Power Supply for Raspberry Pi 5 – IN Plug₹1,319Closest match, check the specs
Official Raspberry Pi 5 Active Cooler: keeps the Pi cool under a HATOfficial Raspberry Pi 5 Active Cooler₹566
Alternatives and when to choose them
- Single NVMe HATs: simpler and faster per drive.
- SATA storage boards: use 2.5 inch drives.
- PCIe network and USB HATs: other PCIe add-ons.
Common mistakes to avoid
- Inserting the FPC cable backwards.
- Using a weak power supply.
- Expecting full speed on both drives.
- Skipping the bootloader update.
Frequently asked questions
Can a Pi 5 use two NVMe SSDs?
Yes, with a PCIe switch board that shares the single lane between them.
Will both SSDs run at full speed?
No. They share one PCIe lane, so total speed is limited.
Can I boot from an SSD behind the switch?
Usually yes with an updated bootloader; check the maker's notes.
Can I add a Hailo AI card and an SSD together?
Yes, on boards made for one SSD and one AI card.
Why does one drive disappear?
Power is short or the FPC cable is loose; reseat and use a stronger supply.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



