Component guide · Advanced · 5 min read
Raspberry Pi 5 PCIe Network and USB HATs

Pineboards HatNET 2.5G, 52Pi U2500, Waveshare 2.5G, 4-Port Gigabit, USB 3.2 and M.2 E Key Boards
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These boards turn the Pi 5's PCIe lane into extra network or USB ports. 2.5G Ethernet HATs (RTL8125) make the Pi a fast router or NAS, the 4-port Gigabit board builds a small firewall, and USB 3.2 boards add more fast ports. Combo boards add an NVMe slot too. All ports share one PCIe lane, so total throughput is about 3 to 7 Gbit/s.
Key specs at a glance
- Network chips
- RTL8125 2.5G, RTL8111 Gigabit, 4-port Gigabit
- USB chips
- VL805 or similar USB 3.2 Gen 1
- Interface
- PCIe 2.0 or 3.0 x1 via FFC
- Combo boards
- Add M.2 NVMe or Mini PCIe
- M.2 E key
- Wi-Fi 6 cards and Coral modules
- OS support
- Raspberry Pi OS, OpenWrt, DietPi
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Pineboards HatNET! 2.5G Ethernet HAT for Raspberry Pi 5₹4,099
Option 252Pi U2500 Dual M.2 NVMe to 2.5G Ethernet for Raspberry Pi 5₹6,799
Option 3Waveshare PCIe to 2.5G Ethernet Board (B) for Raspberry Pi 5₹5,249
Option 4Waveshare PCIe to 2.5G Ethernet Board (C) for Raspberry Pi 5₹1,189
Option 5Waveshare PCIe to 4-Ch Gigabit Ethernet Board for Raspberry Pi 5₹4,299
Option 6Waveshare PCIe to Gigabit Ethernet Board (C) for Pi 5₹819
What the Raspberry Pi 5 PCIe Ethernet, 2.5G and USB 3 HATs is
Pi 5 PCIe Ethernet and USB HATs use the Raspberry Pi 5's PCIe lane to add 2.5 Gb Ethernet, extra USB ports or other controllers.
Recent Raspberry Pi OS kernels include the RTL8125 and RTL8111 drivers, so most 2.5G and Gigabit boards work out of the box. For a router, install OpenWrt or set up nftables with the second port as WAN.
The M.2 E key HAT+ (D) takes Wi-Fi cards or Coral Edge TPU modules rather than SSDs.
Raspberry Pi 5 PCIe Ethernet, 2.5G and USB 3 HATs pinout
The pins on the Raspberry Pi 5 PCIe Ethernet, 2.5G and USB 3 HATs and what each one does.
| Pin | Function |
|---|---|
| PCIe FFC (16-pin) | One PCIe 2.0 x1 lane from the Pi 5 to the board, through a short flat cable |
| M.2 slot | M key for NVMe SSDs or AI accelerators; E key for Wi-Fi cards |
| Power pogo pins / GPIO | Some boards take 5V from the GPIO header or pogo pins, others from the FFC |
| Status LED | Shows power and drive activity on most boards |
- PCIe FFC (16-pin)
- One PCIe 2.0 x1 lane from the Pi 5 to the board, through a short flat cable
- M.2 slot
- M key for NVMe SSDs or AI accelerators; E key for Wi-Fi cards
- Power pogo pins / GPIO
- Some boards take 5V from the GPIO header or pogo pins, others from the FFC
- Status LED
- Shows power and drive activity on most boards
Wiring the Raspberry Pi 5 PCIe Ethernet, 2.5G and USB 3 HATs
Power off first. Lift the latch on the Pi 5 PCIe connector, push the FFC in fully with the contacts facing the pins, close the latch, then do the same on the board. A loose or reversed cable is the most common reason a drive is not detected.
| Raspberry Pi 5 PCIe Ethernet, 2.5G and USB 3 HATs pin | Connection | Note |
|---|---|---|
| FFC cable | Pi 5 PCIe connector to the board's FFC socket | Contacts face the connector pins on both ends |
| Power | From the FFC or the GPIO header | Use the 27W supply |
| Mounting | Standoffs on top (HAT) or under the Pi (bottom board) | Check the cooler fits |
| Network | RJ45 on the HAT | Cat 6 for 2.5G |
- FFC cable
- Connection:
- Pi 5 PCIe connector to the board's FFC socket
- Note:
- Contacts face the connector pins on both ends
- Power
- Connection:
- From the FFC or the GPIO header
- Note:
- Use the 27W supply
- Mounting
- Connection:
- Standoffs on top (HAT) or under the Pi (bottom board)
- Note:
- Check the cooler fits
- Network
- Connection:
- RJ45 on the HAT
- Note:
- Cat 6 for 2.5G
Example code
Gen 3 (dtparam=pciex1_gen=3) raises the shared limit from about 3.5 to about 7 Gbit/s; a single 2.5G port runs fine at Gen 2.
lspci # Realtek RTL8125 or VL805
ip link # new eth1
sudo ethtool eth1 | grep Speed
sudo apt install iperf3
iperf3 -c 192.168.1.10 -B <eth1-ip> # test against another PCSetup and tuning
fit the FPC cable to the PCIe port with contacts facing correctly.
check the chip is supported in Raspberry Pi OS (such as RTL8125 for 2.5 GbE).
one PCIe 2.0 lane limits throughput; Gen 3 mode helps.
check the HAT's power needs and use the 27 W supply.
configure the new interface in NetworkManager.
What you need
Shop this list16 of 17 found in our store · ₹45,297
Pineboards HatNET! 2.5G Ethernet HAT for Raspberry Pi 5: the part this guide coversPineboards HatNET! 2.5G Ethernet HAT for Raspberry Pi 5₹4,099
52Pi U2500 Dual M.2 NVMe to 2.5G Ethernet for Raspberry Pi 5: another version this guide covers52Pi U2500 Dual M.2 NVMe to 2.5G Ethernet for Raspberry Pi 5₹6,799
Waveshare PCIe to 2.5G Ethernet Board (B) for Raspberry Pi 5: another version this guide coversWaveshare PCIe to 2.5G Ethernet Board (B) for Raspberry Pi 5₹5,249
Waveshare PCIe to 2.5G Ethernet Board (C) for Raspberry Pi 5: another version this guide coversWaveshare PCIe to 2.5G Ethernet Board (C) for Raspberry Pi 5₹1,189
Waveshare PCIe to 4-Ch Gigabit Ethernet Board for Raspberry Pi 5: another version this guide coversWaveshare PCIe to 4-Ch Gigabit Ethernet Board for Raspberry Pi 5₹4,299
Waveshare PCIe to Gigabit Ethernet Board (C) for Pi 5: another version this guide coversWaveshare PCIe to Gigabit Ethernet Board (C) for Pi 5₹819
Waveshare PCIe Gigabit ETH & USB 3.2 Gen1 HAT for Raspberry Pi 5: another version this guide coversWaveshare PCIe Gigabit ETH & USB 3.2 Gen1 HAT for Raspberry Pi 5₹3,034
Waveshare PCIe to USB 3.2 Gen1 HAT for Raspberry Pi 5: another version this guide coversWaveshare PCIe to USB 3.2 Gen1 HAT for Raspberry Pi 5₹2,039
Waveshare PCIe to 4-Ch USB 3.2 Board (C) for Raspberry Pi 5: another version this guide coversWaveshare PCIe to 4-Ch USB 3.2 Board (C) for Raspberry Pi 5₹1,650
Waveshare PCIe to USB 3.2 Gen1 & M.2 HAT for Raspberry Pi 5: another version this guide coversWaveshare PCIe to USB 3.2 Gen1 & M.2 HAT for Raspberry Pi 5₹2,799
Waveshare PCIe to USB 3.2, 2.5G ETH, M.2 NVMe HAT for Pi 5: another version this guide coversWaveshare PCIe to USB 3.2, 2.5G ETH, M.2 NVMe HAT for Pi 5₹4,729
Waveshare PCIe to MiniPCIe/GbE/USB 3.2 Gen1 HAT for Pi 5: another version this guide coversWaveshare PCIe to MiniPCIe/GbE/USB 3.2 Gen1 HAT for Pi 5₹2,839
Waveshare PCIe to M.2 E Key HAT+ (D) for Raspberry Pi 5: another version this guide coversWaveshare PCIe to M.2 E Key HAT+ (D) for Raspberry Pi 5₹709
Raspberry Pi 5 (4 GB): the board with the PCIe connectorRaspberry Pi Compute Module 5 IO Board₹3,159Closest match, check the specs
Official 27W USB-C power supply for Pi 5: enough current for the Pi plus an SSDOfficial 27W USB-C PD Power Supply for Raspberry Pi 5 – IN Plug₹1,319Closest match, check the specs
Official Raspberry Pi 5 Active Cooler: keeps the Pi cool under a HATOfficial Raspberry Pi 5 Active Cooler₹566- PUSR industrial PoE switch: supplies power over the Ethernet cableFind this part
Alternatives and when to choose them
- NVMe SSD HATs: storage instead.
- USB and Ethernet hubs for Pi Zero: no PCIe needed.
- PoE HATs: power over the cable.
Common mistakes to avoid
- Expecting full 2.5 Gb speed on Gen 2.
- Reversed FPC cable.
- Weak power supply.
- Unsupported chips.
Frequently asked questions
Can a Pi 5 run 2.5 Gb Ethernet?
Yes, with a PCIe 2.5 GbE HAT, though throughput is limited by the lane.
Do I need drivers?
Check the chip is supported; some need a newer kernel.
Can I use NVMe and Ethernet together?
Only with a PCIe switch board, because the Pi 5 has a single PCIe lane.
Why is the speed lower than expected?
The single PCIe lane is shared or in Gen 2 mode.
Will it work on Pi 4?
No. The Pi 4 has no exposed PCIe connector, so these HATs need a Pi 5.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


