Component guide · Beginner · 4 min read
USB Hub and Ethernet Boards for Raspberry Pi

Waveshare ETH/USB HUB HAT and BOX for Zero, PoE BOX, Official USB 3 Hub, ENC28J60 and WIZnet W5100S HAT
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A Pi Zero has one micro USB port and no Ethernet. These boards add a USB hub, wired Ethernet and sometimes a serial port, either as a HAT, a pogo-pin board underneath or a small case. The official USB 3 hub and Yahboom hub add ports to any Pi, and ENC28J60 and W5100S boards give Ethernet over SPI.
Key specs at a glance
- USB
- 3 or 4 ports, USB 2.0 (Zero) or USB 3.0 (Pi 4/5)
- Ethernet
- RTL8152 USB (100M) or SPI ENC28J60 / W5100S
- Connection
- Pogo pins, micro USB or 40-pin header
- Extras
- USB-UART port, PoE on the PoE BOX
- Power
- From the Pi or the hub's own USB-C
- Pi models
- Zero, Zero 2 W, Pi 4, Pi 5
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Waveshare ETH/USB HUB HAT (B) for Raspberry Pi Zero Series₹1,059
Option 2Waveshare Ethernet/USB HUB BOX for Pi Zero Series₹1,509
Option 3Waveshare PoE Ethernet / USB HUB BOX for Raspberry Pi Zero₹2,900
Option 4Waveshare 4-Port USB 2.0 Hub & Serial Converter for Pi Zero₹999
Option 5Elecrow USB Hub and Power HAT for Raspberry Pi Zero₹708
Option 6Waveshare USB HUB HAT (B) for Raspberry Pi 4-Port USB 2.0₹589
What the USB hub and Ethernet HATs for Raspberry Pi is
Pi USB hub and Ethernet HATs add USB ports and wired LAN to boards like the Pi Zero, which have only one micro-USB data port and no Ethernet.
USB-based hubs are plug and play. SPI Ethernet boards (ENC28J60, W5100S) need an overlay: add dtoverlay=enc28j60 to config.txt. The W5100S HAT is also used with the Pico.
Bus-powered hubs share the Pi's current; use a powered hub for hard drives.
USB hub and Ethernet HATs for Raspberry Pi pinout
The pins on the USB hub and Ethernet HATs for Raspberry Pi and what each one does.
| Pin | Function |
|---|---|
| Pogo pins | Touch the Zero's USB test pads underneath |
| Micro USB plug | Used by plug-in versions |
| SPI (ENC28J60) | MOSI 10, MISO 9, SCLK 11, CE0 8, INT 25 |
| USB-C / micro USB in | Power for the hub and Pi |
- Pogo pins
- Touch the Zero's USB test pads underneath
- Micro USB plug
- Used by plug-in versions
- SPI (ENC28J60)
- MOSI 10, MISO 9, SCLK 11, CE0 8, INT 25
- USB-C / micro USB in
- Power for the hub and Pi
Wiring the USB hub and Ethernet HATs for Raspberry Pi
Tighten pogo-pin boards evenly so all pins touch. ENC28J60 modules are 3.3V; do not feed them 5V on VCC unless the module has a regulator.
| USB hub and Ethernet HATs for Raspberry Pi pin | Connection | Note |
|---|---|---|
| Pogo board | Screw under the Zero with the pins on the test pads | - |
| ENC28J60 | SPI0 and GPIO25 for INT | 3.3V only |
| USB hub | USB-A port | Powered hub for drives |
- Pogo board
- Connection:
- Screw under the Zero with the pins on the test pads
- Note:
- -
- ENC28J60
- Connection:
- SPI0 and GPIO25 for INT
- Note:
- 3.3V only
- USB hub
- Connection:
- USB-A port
- Note:
- Powered hub for drives
Example code
The Waveshare HUB HAT's USB-UART port shows up as a serial console on another computer, handy for headless set-up.
lsusb # hub and RTL8152 network chip
ip link # eth0 appears
# For an SPI ENC28J60 board:
echo "dtoverlay=enc28j60" | sudo tee -a /boot/firmware/config.txt
sudo rebootSetup and tuning
pogo-pin HATs press onto the Pi Zero's USB test pads; align them and tighten the screws.
most use RTL8152 or similar Ethernet chips supported by Raspberry Pi OS.
feed the hub enough power if you attach drives or cameras.
Zero boards share USB 2.0 bandwidth, so Ethernet reaches about 100 Mbps.
set a static IP or check your router for the address.
What you need
Shop this list14 of 14 found in our store · ₹31,788
Waveshare ETH/USB HUB HAT (B) for Raspberry Pi Zero Series: the part this guide coversWaveshare ETH/USB HUB HAT (B) for Raspberry Pi Zero Series₹1,059
Waveshare Ethernet/USB HUB BOX for Pi Zero Series: another version this guide coversWaveshare Ethernet/USB HUB BOX for Pi Zero Series₹1,509
Waveshare PoE Ethernet / USB HUB BOX for Raspberry Pi Zero: another version this guide coversWaveshare PoE Ethernet / USB HUB BOX for Raspberry Pi Zero₹2,900
Waveshare 4-Port USB 2.0 Hub & Serial Converter for Pi Zero: another version this guide coversWaveshare 4-Port USB 2.0 Hub & Serial Converter for Pi Zero₹999
Elecrow USB Hub and Power HAT for Raspberry Pi Zero: another version this guide coversElecrow USB Hub and Power HAT for Raspberry Pi Zero₹708
Waveshare USB HUB HAT (B) for Raspberry Pi 4-Port USB 2.0: another version this guide coversWaveshare USB HUB HAT (B) for Raspberry Pi 4-Port USB 2.0₹589
Waveshare USB 3.2 Gen1 Gigabit Ethernet HUB HAT for Pi: another version this guide coversWaveshare USB 3.2 Gen1 Gigabit Ethernet HUB HAT for Pi₹2,409
Official Raspberry Pi USB 3.0 Hub: another version this guide coversOfficial Raspberry Pi USB 3.0 Hub₹1,270
Yahboom USB 3.0 Hub Expansion Board (1 to 4): another version this guide coversYahboom USB 3.0 Hub Expansion Board (1 to 4)₹3,850
ENC28J60 Ethernet Module for Raspberry Pi Zero/W: another version this guide coversENC28J60 Ethernet Module for Raspberry Pi Zero/W₹1,059
WIZnet Ethernet HAT W5100S for Raspberry Pi: another version this guide coversWIZnet Ethernet HAT W5100S for Raspberry Pi₹881
Raspberry Pi Zero 2 W with header: the small board these hubs stack onRaspberry Pi Zero 2 W with Header₹3,009
Raspberry Pi 4 Model B (4 GB): for USB and GPIO boardsRaspberry Pi 4 Model B with 4GB RAM₹11,461Closest match, check the specs
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
Alternatives and when to choose them
- PCIe network and USB HATs: faster Pi 5 ports.
- W5500 Ethernet: SPI Ethernet for microcontrollers.
- PoE HATs: power over the cable.
Common mistakes to avoid
- Misaligned pogo pins.
- Powering drives without a powered hub.
- Expecting gigabit speeds on a Zero.
- Loose mounting screws.
Frequently asked questions
Can I add Ethernet to a Pi Zero?
Yes, with a USB hub and Ethernet HAT or adapter.
Why does the hub not work?
Pogo pins are not aligned with the test pads; refit and tighten.
How fast is Ethernet on a Pi Zero?
Up to about 100 Mbps because of USB 2.0.
Can it power hard drives?
Only small devices like keyboards and dongles; use a powered hub for hard drives.
Do I need drivers?
Usually not. Raspberry Pi OS already includes drivers for the common Ethernet and hub chips.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
