Component guide · Beginner · 4 min read
Reyax RYLR896, RYLR998 and RYLR993 LoRa Modules

AT Commands and Wiring
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Reyax RYLR modules are LoRa transceivers with a built-in antenna and a simple AT command interface over UART. Set an address and network ID, then AT+SEND=address,length,data sends a message and the other module prints +RCV with RSSI and SNR. No radio library is needed. The RYLR993 adds LoRaWAN and the RYLR999 adds Bluetooth LE.
Key specs at a glance
- RYLR896 / RYLR998
- SX1276 / SX1262 class, 868/915 MHz, about 22 dBm
- RYLR498
- 433/490 MHz version
- RYLR993 / LITE
- LoRaWAN plus point-to-point LoRa
- RYLR999
- LoRa 30 dBm plus BLE 20 dBm
- Supply
- 2.8 to 3.6 V (3.3 V)
- Interface
- UART 115200 baud, AT commands
- Antenna
- On-board PCB or helical antenna
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Reyax RYLR896 868/915MHz LoRa Transceiver Module DIP Version₹2,369
Option 2Reyax RYLR998 868/915MHz LoRa Transceiver Module DIP Version₹1,359
Option 3Reyax RYLR498 433/426/490MHz LoRa Antenna Transceiver Module₹1,740
Option 4Reyax RYLR689 868/915MHz LoRa/(G)FSK Transceiver Module₹629
Option 5Reyax RYLR993 868/915MHz LoRaWAN Transceiver Module₹1,790
Option 6Reyax RYLR993_LITE LoRaWAN Transceiver Module 868/915MHz DIP Board₹3,409
What the Reyax RYLR LoRa module is
A pair of RYLR modules gives a few kilometres of line of sight with nothing but serial text. Every module has an ADDRESS (0 to 65535) and a NETWORKID; modules talk only within the same network. Received messages arrive as +RCV=sender,length,data,RSSI,SNR, which makes link testing easy.
In India the licence-free LoRa band is 865 to 867 MHz (LoRaWAN plan IN865). 433 MHz modules are widely used by hobbyists, but check local rules before a commercial deployment.
Reyax RYLR LoRa module pinout
The pins on the Reyax RYLR LoRa module and what each one does.
| Pin | Function |
|---|---|
| VDD | 3.3 V supply |
| GND | Ground |
| TXD | Module transmit (to controller RX) |
| RXD | Module receive (from controller TX), 3.3 V |
| NRST | Reset, active low |
- VDD
- 3.3 V supply
- GND
- Ground
- TXD
- Module transmit (to controller RX)
- RXD
- Module receive (from controller TX), 3.3 V
- NRST
- Reset, active low
Wiring the Reyax RYLR LoRa module
The RXD pin is 3.3 V; use a resistor divider or level shifter from a 5 V Uno. SoftwareSerial is unreliable at 115200, so on an Uno set AT+IPR=9600 first or use a board with a spare hardware UART.
| Reyax RYLR LoRa module pin | Arduino Uno | ESP32 |
|---|---|---|
| VDD | 3.3V | 3V3 |
| GND | GND | GND |
| TXD | D2 (SoftwareSerial RX) | GPIO 16 (RX2) |
| RXD | D3 via a 4.7k/10k divider | GPIO 17 (TX2) |
| NRST | Leave open or D4 | Leave open or GPIO 4 |
- VDD
- Arduino Uno:
- 3.3V
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- TXD
- Arduino Uno:
- D2 (SoftwareSerial RX)
- ESP32:
- GPIO 16 (RX2)
- RXD
- Arduino Uno:
- D3 via a 4.7k/10k divider
- ESP32:
- GPIO 17 (TX2)
- NRST
- Arduino Uno:
- Leave open or D4
- ESP32:
- Leave open or GPIO 4
Example code
On the second module change ADDRESS to 2 and send to address 1. AT+PARAMETER sets spreading factor, bandwidth, coding rate and preamble; both ends must match.
HardwareSerial lora(2);
void cmd(const String& c) { lora.println(c); delay(300); while (lora.available()) Serial.write(lora.read()); }
void setup() {
Serial.begin(115200);
lora.begin(115200, SERIAL_8N1, 16, 17);
cmd("AT"); // +OK
cmd("AT+ADDRESS=1"); // use 2 on the other module
cmd("AT+NETWORKID=18"); // same on both
cmd("AT+BAND=865000000"); // 865 MHz
}
void loop() {
cmd("AT+SEND=2,5,HELLO"); // to address 2, 5 bytes
unsigned long t = millis();
while (millis() - t < 5000)
while (lora.available()) Serial.write(lora.read()); // +RCV=...
}Setup and tuning
connect with a USB to TTL adapter and type AT in a serial terminal at 115200 baud.
set AT+BAND to a frequency inside the module's range and your local rules.
AT+PARAMETER=12,7,1,4 (SF12, 125 kHz) gives the longest range at the lowest speed.
AT+CPIN sets a shared password; both modules need the same one.
What you need
Shop this list12 of 13 found in our store · ₹15,498
Reyax RYLR896 868/915MHz LoRa Transceiver Module DIP Version: the part this guide coversReyax RYLR896 868/915MHz LoRa Transceiver Module DIP Version₹2,369
Reyax RYLR998 868/915MHz LoRa Transceiver Module DIP Version: another version this guide coversReyax RYLR998 868/915MHz LoRa Transceiver Module DIP Version₹1,359
Reyax RYLR498 433/426/490MHz LoRa Antenna Transceiver Module: another version this guide coversReyax RYLR498 433/426/490MHz LoRa Antenna Transceiver Module₹1,740
Reyax RYLR689 868/915MHz LoRa/(G)FSK Transceiver Module: another version this guide coversReyax RYLR689 868/915MHz LoRa/(G)FSK Transceiver Module₹629
Reyax RYLR993 868/915MHz LoRaWAN Transceiver Module: another version this guide coversReyax RYLR993 868/915MHz LoRaWAN Transceiver Module₹1,790
Reyax RYLR993LITE LoRaWAN Transceiver Module 868/915MHz DIP Board: another version this guide coversReyax RYLR993_LITE LoRaWAN Transceiver Module 868/915MHz DIP Board₹3,409
Reyax RYLR999 LoRa & BLE Transceiver Module, 30dBm 868/915MHz & 20dBm 2.4GHz: another version this guide coversReyax RYLR999 LoRa & BLE Transceiver Module, 30dBm 868/915MHz & 20dBm 2.4GHz₹3,319
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- Uno R3 development board: the controller used in the wiring tableFind this part
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
4-channel logic level converter (BSS138): to connect 5 V and 3.3 V signals safely4-Channel Logic Level Converter (BSS138)₹20
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
DS18B20 waterproof temperature probe: a sensor to send over LoRaSonoff DS18B20 Waterproof Temperature Sensor Probe w/ 1m Cable – 1-Wire Interface₹340Closest match, check the specs
Alternatives and when to choose them
- EByte E32: transparent serial without AT commands.
- SX1278 Ra-02 LoRa: SPI radio for full control.
- LoRaWAN nodes and gateways: for networked LoRaWAN projects.
Common mistakes to avoid
- Driving RXD with 5 V.
- Different NETWORKID or PARAMETER on the two modules.
- Using SoftwareSerial at 115200 baud on an Uno.
- Mounting the built-in antenna against metal.
Frequently asked questions
Do I need an antenna?
No, it is built in, but height and clear line of sight matter.
How many modules can share a network?
Many; each needs a unique address within the same NETWORKID.
Can I broadcast?
Yes, send to address 0 to reach every module in the network.
Is the RYLR896 LoRaWAN?
No. The RYLR993 is the LoRaWAN capable model.
What do RSSI and SNR mean?
Signal strength and quality; above -110 dBm RSSI and positive SNR is a solid link.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


