Component guide · Beginner · 5 min read
EByte E32 LoRa UART Module (433T20D, 433T30D, 900T30D)

Wiring, Modes and Range
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The EByte E32 is a LoRa module with its own microcontroller, so you send and receive plain serial data instead of driving the SX1278 or SX1276 radio over SPI. Set M0 and M1 low for transparent mode, wire TX and RX, and two modules on the same address and channel talk to each other. T20 versions give 100 mW, T30 versions 1 W for several kilometres in open ground.
Key specs at a glance
- Radio chip
- SX1278 (433 MHz) or SX1276 (868/915 MHz)
- Output power
- 20 dBm (100 mW) on T20, 30 dBm (1 W) on T30
- Interface
- UART, 9600 baud default, 8N1
- Supply
- T20: 2.3 to 5.5 V; T30: 3.3 to 5.2 V, 5 V recommended
- Control pins
- M0, M1 (mode) and AUX (busy/ready)
- Range
- About 3 km (T20) and 8 km (T30) line of sight at the slowest air rate
- Package
- D = DIP with SMA, S = SMD with IPEX, M = SPI-only module
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1EByte E32-433T20D LoRa UART Module 433MHz 20dBm₹789
Option 2CDSENet E32-433T20DT LoRa SX1278 RF Module 433MHz₹1,005
Option 3E32-433T30DV8 LoRa 433MHz RF Transceiver Module w/ SMA Connector₹1,595
Option 4E32-868T30D LoRa SX1276 RF Transceiver Module 868MHz₹1,870
Option 5EByte E32-400M20S LoRa Wireless Module w/ SX1278₹559
Option 6EByte E32-433T20S LoRa Module 433MHz SX1278 100mW₹669
What the EByte E32 LoRa UART module is
The E32 hides LoRa settings behind four modes. Normal mode sends serial data as radio packets, wake-up mode adds a long preamble to wake sleeping nodes, power-saving mode listens on a duty cycle, and sleep mode (M0 and M1 high) is used to read and write settings. Address, channel, air data rate and power are stored inside the module.
The E32-400M20S is the exception: it is a plain SPI SX1278 module and is driven like a Ra-02 with the LoRa library.
In India the licence-free LoRa band is 865 to 867 MHz (LoRaWAN plan IN865). 433 MHz modules are widely used by hobbyists, but check local rules before a commercial deployment.
EByte E32 LoRa UART module pinout
The pins on the EByte E32 LoRa UART module and what each one does.
| Pin | Function |
|---|---|
| M0 | Mode select bit 0 |
| M1 | Mode select bit 1 |
| RXD | Module UART input (from controller TX) |
| TXD | Module UART output (to controller RX) |
| AUX | Low while busy or starting, high when ready |
| VCC | Supply (see specs) |
| GND | Ground |
- M0
- Mode select bit 0
- M1
- Mode select bit 1
- RXD
- Module UART input (from controller TX)
- TXD
- Module UART output (to controller RX)
- AUX
- Low while busy or starting, high when ready
- VCC
- Supply (see specs)
- GND
- Ground
Wiring the EByte E32 LoRa UART module
The module pins are 3.3 V logic. Most E32 D versions tolerate a 5 V Uno, but a 4.7k pull-up on TXD and RXD helps, and a level shifter is safest. 1 W T30 modules draw about 600 mA when sending, so power them from a separate 5 V supply with a common ground.
| EByte E32 LoRa UART module pin | Arduino Uno | ESP32 |
|---|---|---|
| M0 | D7 | GPIO 4 |
| M1 | D8 | GPIO 5 |
| RXD | D3 (SoftwareSerial TX) via 4.7k pull-up | GPIO 17 (TX2) |
| TXD | D2 (SoftwareSerial RX) | GPIO 16 (RX2) |
| AUX | D6 | GPIO 18 |
| VCC | 5V (separate supply for T30) | 5V (VIN) |
| GND | GND | GND |
- M0
- Arduino Uno:
- D7
- ESP32:
- GPIO 4
- M1
- Arduino Uno:
- D8
- ESP32:
- GPIO 5
- RXD
- Arduino Uno:
- D3 (SoftwareSerial TX) via 4.7k pull-up
- ESP32:
- GPIO 17 (TX2)
- TXD
- Arduino Uno:
- D2 (SoftwareSerial RX)
- ESP32:
- GPIO 16 (RX2)
- AUX
- Arduino Uno:
- D6
- ESP32:
- GPIO 18
- VCC
- Arduino Uno:
- 5V (separate supply for T30)
- ESP32:
- 5V (VIN)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
Example code
Load the same sketch on two boards and change the message. To change the address, channel or power, set M0 and M1 high and use the EByte RF Setting tool or the LoRa_E32 Arduino library.
#include <HardwareSerial.h>
HardwareSerial lora(2); // ESP32 UART2: RX 16, TX 17
const int M0 = 4, M1 = 5, AUX = 18;
void setup() {
Serial.begin(115200);
pinMode(M0, OUTPUT); pinMode(M1, OUTPUT); pinMode(AUX, INPUT);
digitalWrite(M0, LOW); digitalWrite(M1, LOW); // normal (transparent) mode
lora.begin(9600, SERIAL_8N1, 16, 17);
while (digitalRead(AUX) == LOW) delay(10); // wait until the module is ready
Serial.println("LoRa ready");
}
void loop() {
static unsigned long t = 0;
if (millis() - t > 5000) { // send every 5 s
t = millis();
lora.println("Hello from node 1");
}
while (lora.available()) Serial.write(lora.read()); // print anything received
}Setup and tuning
address, channel and air data rate must match for transparent mode.
2.4 kbps is the default; 0.3 kbps gives the longest range, 19.2 kbps the fastest.
put the target address and channel in the first three bytes to send to one node only.
never transmit without an antenna, and raise both antennas well above ground.
EByte's RF Setting software works through a USB to TTL adapter with M0 and M1 high.
What you need
Shop this list14 of 16 found in our store · ₹11,667
EByte E32-433T20D LoRa UART Module 433MHz 20dBm: the part this guide coversEByte E32-433T20D LoRa UART Module 433MHz 20dBm₹789
CDSENet E32-433T20DT LoRa SX1278 RF Module 433MHz: another version this guide coversCDSENet E32-433T20DT LoRa SX1278 RF Module 433MHz₹1,005
E32-433T30DV8 LoRa 433MHz RF Transceiver Module w/ SMA Connector: another version this guide coversE32-433T30DV8 LoRa 433MHz RF Transceiver Module w/ SMA Connector₹1,595
E32-868T30D LoRa SX1276 RF Transceiver Module 868MHz: another version this guide coversE32-868T30D LoRa SX1276 RF Transceiver Module 868MHz₹1,870
EByte E32-400M20S LoRa Wireless Module w/ SX1278: another version this guide coversEByte E32-400M20S LoRa Wireless Module w/ SX1278₹559
EByte E32-433T20S LoRa Module 433MHz SX1278 100mW: another version this guide coversEByte E32-433T20S LoRa Module 433MHz SX1278 100mW₹669
EByte E32-433T30D-V8 LoRa 433MHz UART Transceiver w/ SMA Antenna: another version this guide coversEByte E32-433T30D-V8 LoRa 433MHz UART Transceiver w/ SMA Antenna₹1,239
EByte E32-433T30S 433MHz LoRa SX1278 Transceiver Module: another version this guide coversEByte E32-433T30S 433MHz LoRa SX1278 Transceiver Module₹1,279
EByte E32-900T20D 868MHz LoRa Module 20dBm UART: another version this guide coversEByte E32-900T20D 868MHz LoRa Module 20dBm UART₹789
EByte E32-900T30D LoRa Module 868/915MHz SX1276 30dBm 1W: another version this guide coversEByte E32-900T30D LoRa Module 868/915MHz SX1276 30dBm 1W₹1,339- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
433MHz 2.5dBi folding antenna: a proper antenna for 433 MHz modulesHelical Spring Coil Antenna₹40- LM2596 buck converter: a clean 5 V supply for 1 W modulesFind this part
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
4-channel logic level converter (BSS138): to connect 5 V and 3.3 V signals safely4-Channel Logic Level Converter (BSS138)₹20
Alternatives and when to choose them
- EByte E22 LoRa module: newer SX1268/SX1262 version with relay networking.
- EByte E220 LLCC68: low-cost successor with the same pinout.
- SX1278 Ra-02 LoRa: the bare SPI radio for full control.
Common mistakes to avoid
- Leaving M0 and M1 floating, so the module sits in the wrong mode.
- Different air data rates on the two modules.
- Powering a 1 W T30 module from the Arduino 5V pin.
- Sending before AUX goes high after power-up.
Frequently asked questions
Do I need a LoRa library?
No. In normal mode it behaves like a wireless serial cable; a library only helps with settings.
How far does the E32 reach?
Hundreds of metres in a city and several kilometres line of sight, more with the T30 and a good antenna.
Can an E32 talk to a Ra-02?
Not easily. The E32 adds its own packet format, so pair E32 with E32.
Is it LoRaWAN?
No. It is point to point LoRa; use a LoRaWAN node module for The Things Network.
433T20D or 433T30D?
T20 for short range and batteries, T30 for long range with a mains supply.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



