Concept explainer · Intermediate · 3 min read
Antennas and RF Connectors
SMA, RP-SMA, u.FL and IPEX
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
An antenna must match the radio's frequency band, such as 433 MHz, 868 MHz, 2.4 GHz or GPS at 1575 MHz, and its connector. SMA and RP-SMA look similar but have opposite centre pins, so check before ordering. Tiny u.FL or IPEX connectors on modules link to a panel connector through a short pigtail. Higher dBi gain focuses signal rather than adding power, and transmitting without an antenna can damage some radios.
Key specs at a glance
- SMA
- Male plug has a centre pin; common on LoRa, GSM and SDR
- RP-SMA
- Reverse polarity: male plug has a socket; common on Wi-Fi gear
- u.FL / IPEX
- Tiny snap-on connectors on modules; rated for few mating cycles
- Gain
- 2 to 3 dBi typical rubber duck; 5 to 9 dBi higher-gain omni
- Bands
- 433, 868/915 MHz, 2.4 GHz, 5 GHz, GSM/LTE bands, GNSS 1575 MHz
- Impedance
- 50 Ω for nearly all hobby radios
Matching the antenna to the radio
An antenna tuned for 2.4 GHz performs poorly on 433 MHz, even if the connector fits. Check the band on the antenna label against your module: LoRa in India commonly uses 865 to 867 MHz, 433 MHz RF modules need 433 MHz antennas, GPS needs an active or passive GNSS antenna, and Wi-Fi and Bluetooth use 2.4 GHz.
A simple wire antenna works for low-cost modules: a quarter wavelength is about 17 cm at 433 MHz, 8.6 cm at 868 MHz and 3.1 cm at 2.4 GHz. The frequency and wavelength calculator gives exact lengths.
Connectors and pigtails
both have the same thread, but the centre pin is swapped. A mismatched pair screws together but makes no contact, so the radio seems to have no range.
press straight down until it clicks, and lift straight up with a tool. They wear out after a few dozen connections, so fit the pigtail once.
a short u.FL to SMA or RP-SMA cable lets you mount the antenna on an enclosure wall. Keep it short; thin coax loses signal, especially at 2.4 GHz and above.
Gain, patterns and placement
Gain in dBi does not create power; it reshapes the pattern. A high-gain omni antenna squashes coverage into a flatter disc, good for long range at the same height but weaker straight above and below. Directional antennas such as Yagis and patches point the signal one way.
Placement matters more than gain: mount antennas high, vertical, clear of metal and away from the board's noisy parts. Never transmit with no antenna connected, because reflected power can damage some transmitters. Follow local radio rules on power and gain.
Try it: Frequency wavelength calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Mixing SMA and RP-SMA parts.
- Using an antenna made for a different band.
- Repeatedly plugging and unplugging u.FL connectors.
- Long thin coax runs at 2.4 GHz.
- Transmitting with no antenna attached.
Frequently asked questions
How can I tell SMA from RP-SMA?
Look at the male plug (with the outer nut): SMA has a centre pin, RP-SMA has a hollow socket.
Does a higher dBi antenna give more range?
Often in the horizontal direction, but it reduces coverage above and below.
Can I use a Wi-Fi antenna for LoRa?
No. Wi-Fi antennas are tuned for 2.4 or 5 GHz, LoRa uses sub-GHz bands.
What is a pigtail?
A short cable with a u.FL plug on one end and an SMA or RP-SMA connector on the other.
How long should a wire antenna be?
A quarter wavelength: about 17 cm at 433 MHz and 8.6 cm at 868 MHz.
Parts for this guide
- ₹20View
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
- Amphenol RF SMA and RP-SMA connector specifications
- Hirose U.FL series datasheet
- ARRL Antenna Book (quarter-wave antenna basics)
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

