Component guide · Intermediate · 4 min read
EByte E22 LoRa Module (400T22S, 400T33S, 900T22S)

UART Modes and Relay Networking
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The EByte E22 series puts an SX1268 (433 MHz) or SX1262 (868/915 MHz) radio behind a UART, like the E32 but with better sensitivity, lower current and a built-in relay mode that lets one module repeat packets for another. The T versions use M0 and M1 for mode select; the E22-400M33S is a bare SPI module driven with RadioLib.
Key specs at a glance
- Radio chip
- SX1268 (400 series) or SX1262 (900 series)
- Output power
- 22 dBm on T22, 33 dBm (2 W) on T33 and M33
- Interface
- UART on T versions, SPI on M33S
- Supply
- 3.3 to 5.5 V (T22), 5 V at about 1.2 A peak for 33 dBm parts
- Sensitivity
- About -147 dBm at the lowest air rate
- Extras
- Relay networking, RSSI per packet, listen-before-talk, encryption key
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
What the EByte E22 LoRa module is
The UART E22 modules use the same idea as the E32: transparent or fixed transmission, settings stored in registers, and an AUX pin that shows when the module is busy. Their register layout is different, so E22 settings tools and libraries are separate from E32 ones.
Relay mode lets a module in the middle forward packets between two nodes that cannot hear each other, which stretches a link over a hill or through a building without extra code.
In India the licence-free LoRa band is 865 to 867 MHz (LoRaWAN plan IN865). 433 MHz modules are widely used by hobbyists, but check local rules before a commercial deployment.
EByte E22 LoRa module pinout
The pins on the EByte E22 LoRa module and what each one does.
| Pin | Function |
|---|---|
| M0 / M1 | Mode select (normal, WOR, configuration, deep sleep) |
| RXD / TXD | UART to the controller |
| AUX | Busy/ready indicator |
| VCC / GND | Supply |
| NSS, SCK, MOSI, MISO, BUSY, DIO1 (M33S) | SPI radio pins on the SPI version |
| TXEN / RXEN (M33S) | Switch the power amplifier and receive path |
- M0 / M1
- Mode select (normal, WOR, configuration, deep sleep)
- RXD / TXD
- UART to the controller
- AUX
- Busy/ready indicator
- VCC / GND
- Supply
- NSS, SCK, MOSI, MISO, BUSY, DIO1 (M33S)
- SPI radio pins on the SPI version
- TXEN / RXEN (M33S)
- Switch the power amplifier and receive path
Wiring the EByte E22 LoRa module
Logic is 3.3 V; use a level shifter with a 5 V Uno. 33 dBm modules need a separate 5 V supply that can deliver well over 1 A, and must never transmit without an antenna.
| EByte E22 LoRa module pin | Arduino Uno | ESP32 |
|---|---|---|
| M0 | D7 | GPIO 4 |
| M1 | D8 | GPIO 5 |
| RXD | D3 (SoftwareSerial TX) | GPIO 17 (TX2) |
| TXD | D2 (SoftwareSerial RX) | GPIO 16 (RX2) |
| AUX | D6 | GPIO 18 |
| VCC | 5V | 5V (VIN) |
| GND | GND | GND |
- M0
- Arduino Uno:
- D7
- ESP32:
- GPIO 4
- M1
- Arduino Uno:
- D8
- ESP32:
- GPIO 5
- RXD
- Arduino Uno:
- D3 (SoftwareSerial TX)
- ESP32:
- GPIO 17 (TX2)
- TXD
- Arduino Uno:
- D2 (SoftwareSerial RX)
- ESP32:
- GPIO 16 (RX2)
- AUX
- Arduino Uno:
- D6
- ESP32:
- GPIO 18
- VCC
- Arduino Uno:
- 5V
- ESP32:
- 5V (VIN)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
Example code
The default UART is 9600 baud with M0 and M1 low. Use the LoRa_E22 library by Renzo Mischianti or the EByte setting tool (M1 high, M0 low on E22) to change channel, address and power.
#include <HardwareSerial.h>
HardwareSerial lora(2); // ESP32 UART2: RX 16, TX 17
const int M0 = 4, M1 = 5, AUX = 18;
void setup() {
Serial.begin(115200);
pinMode(M0, OUTPUT); pinMode(M1, OUTPUT); pinMode(AUX, INPUT);
digitalWrite(M0, LOW); digitalWrite(M1, LOW); // normal (transparent) mode
lora.begin(9600, SERIAL_8N1, 16, 17);
while (digitalRead(AUX) == LOW) delay(10); // wait until the module is ready
Serial.println("LoRa ready");
}
void loop() {
static unsigned long t = 0;
if (millis() - t > 5000) { // send every 5 s
t = millis();
lora.println("Hello from node 1");
}
while (lora.available()) Serial.write(lora.read()); // print anything received
}Setup and tuning
on the E22, M0 low and M1 high enters configuration, which differs from the E32.
enable packet RSSI in the settings to append signal strength to each received packet.
set a middle node to relay mode and give the end nodes network IDs on each side.
use an outdoor antenna on a mast for 2 W modules; a short stub wastes most of the power.
What you need
Shop this list8 of 10 found in our store · ₹6,330
EByte E22-400T22S LoRa RF Module 433MHz 22dBm UART: the part this guide coversEByte E22-400T22S LoRa RF Module 433MHz 22dBm UART₹929
EByte E22-400T33S UART 433MHz LoRa Module w/ Relay Networking: another version this guide coversEByte E22-400T33S UART 433MHz LoRa Module w/ Relay Networking₹2,319
EByte E22-900T22S 868/915MHz 22dBm LoRa RF Module: another version this guide coversEByte E22-900T22S 868/915MHz 22dBm LoRa RF Module₹1,009
EByte E22-400M33S 433/470MHz 33dBm SX1268 LoRa Transceiver Module: another version this guide coversEByte E22-400M33S 433/470MHz 33dBm SX1268 LoRa Transceiver Module₹1,539
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- Uno R3 development board: the controller used in the wiring tableFind this part
433MHz 2.5dBi folding antenna: a proper antenna for 433 MHz modulesHelical Spring Coil Antenna₹40- LM2596 buck converter: a clean 5 V supply for 1 W modulesFind this part
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
4-channel logic level converter (BSS138): to connect 5 V and 3.3 V signals safely4-Channel Logic Level Converter (BSS138)₹20
Alternatives and when to choose them
- EByte E32: older SX1278 based UART module.
- EByte E220 LLCC68: cheaper, slightly lower sensitivity.
- SX1262 LoRa module: bare SPI radio for LoRaWAN and RadioLib.
Common mistakes to avoid
- Using E32 configuration commands on an E22.
- Powering a 2 W module from a USB port.
- Mixing network IDs so relay nodes ignore packets.
- Transmitting without an antenna.
Frequently asked questions
Can E22 talk to E32?
No. The packet formats differ; pair modules of the same series.
What is relay networking?
A middle module forwards packets between two nodes that are out of range of each other.
Is the E22 LoRaWAN capable?
Not the UART versions. The SPI E22-400M33S can run LoRaWAN code with a suitable library and band.
How much current does a 33 dBm module draw?
Around 1 A or more while transmitting.
Which version for India?
The 400 series for 433 MHz projects; for 865 MHz use the 900 series set to that band.
Parts for this guide
Keep learning
Sources
- EByte E22 series user manuals
- LoRa_E22 Arduino library documentation
- Semtech SX1268 and SX1262 datasheets
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



