Component guide · Beginner · 4 min read
EByte E220 LLCC68 LoRa Module (900T22D, 900T30D, M-series SPI)

Wiring and Setup
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The EByte E220 uses Semtech's LLCC68, a low-cost LoRa chip compatible with the SX1262, in two forms. The T versions are UART modules with M0, M1 and AUX pins that work like an E32 wireless serial cable. The M versions are bare SPI modules for RadioLib. Pick T22 for 160 mW and battery nodes, T30 or M30 for 1 W links.
Key specs at a glance
- Radio chip
- Semtech LLCC68
- Bands
- 400 series 410 to 493 MHz; 900 series 850 to 930 MHz
- Output power
- 22 dBm (T22, M22) or 30 dBm (T30, M30) or 33 dBm (M33)
- Interface
- UART on T versions, SPI on M versions
- Spreading factor
- SF5 to SF11 (SF12 not available on LLCC68)
- Range
- About 5 km (22 dBm) to 10 km (30 dBm) line of sight
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1EByte E220-900T22S LoRa Module LLCC68 Chip 22dBm 850-930MHz w/ IPEX Antenna₹569
Option 2EByte E220-900T22D LoRa UART Module LLCC68 868/915MHz 22dBm w/ SMA-K Antenna₹669
Option 3EByte E220-900T30D LLCC68 LoRa RF Module 915MHz₹1,139
Option 4EByte E220-900T30S LLCC68 850-930MHz LoRa UART RF Module 30dBm₹1,039
Option 5EByte E220-400M30S LLCC68 433/470MHz LoRaWAN RF Module 30dBm w/ IPEX₹649
Option 6EByte E220-400M33S LLCC68 433/470MHz LoRa Module₹1,239
What the EByte E220 LLCC68 LoRa module is
The LLCC68 drops SF12 and some bandwidth combinations from the SX1262 to cut cost, which slightly shortens the maximum range but makes little difference for most projects. It uses the same SPI commands as the SX1262, so RadioLib's LLCC68 class works for the M versions.
The UART T versions keep the familiar EByte modes and add packet RSSI and listen-before-talk. Their settings are close to the E22, so the LoRa_E220 library is used to change them.
In India the licence-free LoRa band is 865 to 867 MHz (LoRaWAN plan IN865). 433 MHz modules are widely used by hobbyists, but check local rules before a commercial deployment.
EByte E220 LLCC68 LoRa module pinout
The pins on the EByte E220 LLCC68 LoRa module and what each one does.
| Pin | Function |
|---|---|
| M0 / M1 | Mode select (T versions) |
| RXD / TXD | UART (T versions) |
| AUX | Busy/ready (T versions) |
| NSS, SCK, MOSI, MISO | SPI (M versions) |
| BUSY, DIO1, NRST | Radio status, interrupt and reset (M versions) |
| TXEN / RXEN | RF switch control on M30 and M33 |
| VCC / GND | Supply |
- M0 / M1
- Mode select (T versions)
- RXD / TXD
- UART (T versions)
- AUX
- Busy/ready (T versions)
- NSS, SCK, MOSI, MISO
- SPI (M versions)
- BUSY, DIO1, NRST
- Radio status, interrupt and reset (M versions)
- TXEN / RXEN
- RF switch control on M30 and M33
- VCC / GND
- Supply
Wiring the EByte E220 LLCC68 LoRa module
This table is for the UART T versions. For SPI M versions wire NSS to GPIO 5, SCK 18, MISO 19, MOSI 23, DIO1 to GPIO 26, BUSY to GPIO 27 and NRST to GPIO 14 on an ESP32, and drive TXEN and RXEN if fitted. All signals are 3.3 V.
| EByte E220 LLCC68 LoRa module pin | Arduino Uno | ESP32 |
|---|---|---|
| M0 | D7 | GPIO 4 |
| M1 | D8 | GPIO 5 |
| RXD | D3 (SoftwareSerial TX) | GPIO 17 (TX2) |
| TXD | D2 (SoftwareSerial RX) | GPIO 16 (RX2) |
| AUX | D6 | GPIO 18 |
| VCC | 5V | 5V (VIN) |
| GND | GND | GND |
- M0
- Arduino Uno:
- D7
- ESP32:
- GPIO 4
- M1
- Arduino Uno:
- D8
- ESP32:
- GPIO 5
- RXD
- Arduino Uno:
- D3 (SoftwareSerial TX)
- ESP32:
- GPIO 17 (TX2)
- TXD
- Arduino Uno:
- D2 (SoftwareSerial RX)
- ESP32:
- GPIO 16 (RX2)
- AUX
- Arduino Uno:
- D6
- ESP32:
- GPIO 18
- VCC
- Arduino Uno:
- 5V
- ESP32:
- 5V (VIN)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
Example code
Same sketch on both modules. For the SPI M versions use RadioLib: LLCC68 radio = new Module(5, 26, 14, 27); then radio.begin(865.0) and radio.transmit("hello").
#include <HardwareSerial.h>
HardwareSerial lora(2); // ESP32 UART2: RX 16, TX 17
const int M0 = 4, M1 = 5, AUX = 18;
void setup() {
Serial.begin(115200);
pinMode(M0, OUTPUT); pinMode(M1, OUTPUT); pinMode(AUX, INPUT);
digitalWrite(M0, LOW); digitalWrite(M1, LOW); // normal (transparent) mode
lora.begin(9600, SERIAL_8N1, 16, 17);
while (digitalRead(AUX) == LOW) delay(10); // wait until the module is ready
Serial.println("LoRa ready");
}
void loop() {
static unsigned long t = 0;
if (millis() - t > 5000) { // send every 5 s
t = millis();
lora.println("Hello from node 1");
}
while (lora.available()) Serial.write(lora.read()); // print anything received
}Setup and tuning
M0 and M1 low is normal mode; both high is configuration or sleep on the E220.
9600 baud, address 0, channel 23 on the 900 series; both ends must match.
LoRa_E220 by Renzo Mischianti reads and writes the settings.
RadioLib supports the LLCC68 directly; set SF11 or lower.
What you need
Shop this list12 of 14 found in our store · ₹7,480
EByte E220-900T22S LoRa Module LLCC68 Chip 22dBm 850-930MHz w/ IPEX Antenna: the part this guide coversEByte E220-900T22S LoRa Module LLCC68 Chip 22dBm 850-930MHz w/ IPEX Antenna₹569
EByte E220-900T22D LoRa UART Module LLCC68 868/915MHz 22dBm w/ SMA-K Antenna: another version this guide coversEByte E220-900T22D LoRa UART Module LLCC68 868/915MHz 22dBm w/ SMA-K Antenna₹669
EByte E220-900T30D LLCC68 LoRa RF Module 915MHz: another version this guide coversEByte E220-900T30D LLCC68 LoRa RF Module 915MHz₹1,139
EByte E220-900T30S LLCC68 850-930MHz LoRa UART RF Module 30dBm: another version this guide coversEByte E220-900T30S LLCC68 850-930MHz LoRa UART RF Module 30dBm₹1,039
EByte E220-400M30S LLCC68 433/470MHz LoRaWAN RF Module 30dBm w/ IPEX: another version this guide coversEByte E220-400M30S LLCC68 433/470MHz LoRaWAN RF Module 30dBm w/ IPEX₹649
EByte E220-400M33S LLCC68 433/470MHz LoRa Module: another version this guide coversEByte E220-400M33S LLCC68 433/470MHz LoRa Module₹1,239
EByte E220-900M22S LLCC68 LoRa Module 868/915MHz SPI: another version this guide coversEByte E220-900M22S LLCC68 LoRa Module 868/915MHz SPI₹329
EByte E220-900M30S LoRa Module LLCC68 868MHz/915MHz 30dBm: another version this guide coversEByte E220-900M30S LoRa Module LLCC68 868MHz/915MHz 30dBm₹879
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- Uno R3 development board: the controller used in the wiring tableFind this part
868MHz 4dBi SMA antenna with 3 m cable: an outdoor antenna for 865 to 868 MHzLWC-868-MM-03 868MHz 4dBi SMA Antenna w/ 3m RG58 Cable₹412Closest match, check the specs
IPEX to SMA pigtail cable: to fit an SMA antenna to an IPEX socket5cm RG178 IPEX 1 to RP-SMA Female RF Pigtail Cable₹82Closest match, check the specs- LM2596 buck converter: a clean 5 V supply for 1 W modulesFind this part
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
Alternatives and when to choose them
- EByte E22: SX1262 based, adds SF12 and relay mode.
- EByte E32: older SX1278 version.
- SX1262 LoRa module: bare SPI radio with the full feature set.
Common mistakes to avoid
- Setting SF12, which the LLCC68 does not support.
- Using E32 libraries on an E220.
- Forgetting TXEN and RXEN on the SPI M30 module, so it never transmits.
- Driving the module with 5 V logic.
Frequently asked questions
Is the LLCC68 the same as SX1262?
Nearly: same commands and pins, but without SF12 and some bandwidths.
Can E220 work with E22?
Generally no; keep both ends in the same series.
Does it support LoRaWAN?
The UART versions do not. The SPI versions can run LoRaWAN code, though SF12 is unavailable.
T22D or T30D?
T22D for batteries and short links, T30D for long range with a 5 V supply.
Which band for India?
The 900 series set to 865 to 867 MHz.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



