Buying guide · Intermediate · 3 min read
RISC-V Development Boards
ARIES, CH32V, BeagleV and More
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
RISC-V is an open processor design that anyone can build chips from. Boards range from tiny CH32V003 microcontrollers that cost very little, to C-DAC ARIES boards built on India's VEGA THEJAS32 SoC, to BeagleV boards that run Linux. Pick a microcontroller board to learn embedded RISC-V, or a Linux board for applications, and check the toolchain and community support first.
Key specs at a glance
- Microcontrollers
- WCH CH32V003, CH32V203 (QT Py), THEJAS32 on ARIES boards
- Linux boards
- BeagleV-Ahead with the T-Head TH1520
- Toolchains
- GCC for RISC-V, PlatformIO, vendor IDEs, Arduino cores
- ARIES
- C-DAC boards in v2, v3 and ECO versions
- Peripherals
- GPIO, UART, SPI, I2C, ADC on most MCU boards
- Cost
- Very low for CH32V003 boards
Why RISC-V
RISC-V is an open instruction set, so companies and universities can design their own chips without licence fees. For learners it is a clean architecture to study, and for products it gives cost and independence choices. The C code you write is largely portable from other microcontrollers.
Boards compared
Choose by the kind of work you want to do.
| Board | Chip | Good for |
|---|---|---|
| CH32V003 boards (CAPUF OLED board) | WCH 48 MHz RISC-V MCU | Cheap learning and tiny projects |
| Adafruit QT Py CH32V203 | WCH CH32V203 | Compact board with STEMMA QT |
| C-DAC ARIES v2 / v3 / ECO | THEJAS32 (VEGA RISC-V SoC) | Indian-designed learning and research |
| BeagleV-Ahead | T-Head TH1520, Linux | RISC-V Linux development |
- CH32V003 boards (CAPUF OLED board)
- Chip:
- WCH 48 MHz RISC-V MCU
- Good for:
- Cheap learning and tiny projects
- Adafruit QT Py CH32V203
- Chip:
- WCH CH32V203
- Good for:
- Compact board with STEMMA QT
- C-DAC ARIES v2 / v3 / ECO
- Chip:
- THEJAS32 (VEGA RISC-V SoC)
- Good for:
- Indian-designed learning and research
- BeagleV-Ahead
- Chip:
- T-Head TH1520, Linux
- Good for:
- RISC-V Linux development
Getting started
1. Pick the board and read its getting-started page. 2. Install the toolchain, an IDE or PlatformIO. 3. Flash a blink example through USB or a programmer; see debug probes and programmers. 4. Use the serial port for output; see UART. 5. Move on to I2C and SPI sensors, and then to your own project. ARIES boards support an Arduino-like workflow, which helps beginners.
Things to expect
Libraries and tutorials are fewer than for Arduino or ESP32, so you may need to read datasheets and port code. Documentation quality varies between vendors. For beginners who just want a working project, see choosing a microcontroller; for another low-cost route, see RP2040 boards.
Try it: Adc resolution calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Expecting every Arduino library to work unchanged.
- Choosing a Linux RISC-V board for a simple blink project.
- Skipping the vendor toolchain instructions.
- Ignoring the 3.3 V logic levels.
- Not checking whether the board supports Arduino or MicroPython.
Frequently asked questions
Is RISC-V better than ARM?
Neither is better for every job. RISC-V is open and low-cost; ARM has a larger software ecosystem.
What is VEGA?
India's family of RISC-V processors developed by C-DAC, used on ARIES boards.
Can I run Linux on RISC-V?
Yes, on boards such as BeagleV-Ahead.
What is the CH32V003?
A very low-cost 32-bit RISC-V microcontroller from WCH.
Which IDE should I use?
The one the board vendor recommends, or PlatformIO.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






