Component guide · Intermediate · 5 min read
RS485 Modbus Gas Transmitters

Renke RS-CO / CO2 / CH4 / H2S / NH3 / NO2 / O2 / O3 / SO2 / TVOC / CH2O, JXBS, SN-3002, DFRobot)
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
RS485 gas transmitters put a calibrated gas sensor in a wall or pipe enclosure with a 10 to 30 V supply and Modbus RTU output. They are used in farms, parking garages, labs and plants, and connect to PLCs, gateways or an ESP32 with a MAX485 module. Renke, JXBS and SN-3002 units cover CO, CO2, methane, H2S, ammonia, NO2, oxygen, ozone, SO2, TVOC and formaldehyde.
Key specs at a glance
- Supply
- 10 to 30 V DC
- Bus
- RS485 Modbus RTU
- Default
- Address 1, 4800 or 9600 baud by maker
- Outputs
- RS485; some add 4 to 20 mA or 0 to 10 V
- Sensors
- Electrochemical, NDIR (CO2) or MOS (TVOC)
- Enclosure
- Wall mount, some IP65 or explosion-proof
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Renke RS-CO-N01-2-1000P Carbon Monoxide Sensor – 0-1000ppm, RS485 Modbus₹6,779
Option 2Renke RS-CO2-N01-2-5000P Carbon Dioxide Sensor, 0-5000ppm, -40°C to 80°C, RS485 Modbus₹7,629
Option 3Renke RS-CH4-N01-2 Methane Gas Sensor -40℃~+80℃, ±0.06% – RS485 Modbus-RTU₹8,339
Option 4Renke RS-H2S-N01-2-100P-2 Hydrogen Sulphide & Temperature/Humidity Sensor – RS485 Modbus, Wall Mounted₹5,719
Option 5Renke RS-NH3-N01-2-100P-2-YL-EX Ammonia Gas Sensor – RS485 Modbus, 0-100ppm Range, Wall-Mount₹14,429
Option 6Renke RS-NH3-N01-2-50P Ammonia Sensor 0-50ppm – RS485 Modbus Output₹24,179
What the RS485 Modbus gas transmitters is
RS485 gas transmitters are industrial gas detectors for CO, H2S, NH3, O2 and combustible gases that report concentration over Modbus RTU, often with relays and alarms.
Each maker documents the register that holds the gas value and its scale (for example x10 or x100). Read the manual, then test with a USB to RS485 adapter and a Modbus tool before writing code.
Several transmitters can share one bus when each has its own address.
RS485 Modbus gas transmitters pinout
The pins on the RS485 Modbus gas transmitters and what each one does.
| Pin | Function |
|---|---|
| Brown | V+ 10 to 30 V |
| Black | GND |
| Yellow | RS485 A |
| Blue | RS485 B |
- Brown
- V+ 10 to 30 V
- Black
- GND
- Yellow
- RS485 A
- Blue
- RS485 B
Wiring the RS485 Modbus gas transmitters
Tie the supply ground to the controller ground. Add 120 ohm termination on long runs.
| RS485 Modbus gas transmitters pin | Arduino Uno | ESP32 |
|---|---|---|
| Transmitter A | MAX485 A | MAX485 A |
| Transmitter B | MAX485 B | MAX485 B |
| V+ / GND | 12 or 24 V supply | 12 or 24 V supply |
| MAX485 RO / DI / DE+RE | Software serial and D4 | GPIO 16 / 17 / 4 |
- Transmitter A
- Arduino Uno:
- MAX485 A
- ESP32:
- MAX485 A
- Transmitter B
- Arduino Uno:
- MAX485 B
- ESP32:
- MAX485 B
- V+ / GND
- Arduino Uno:
- 12 or 24 V supply
- ESP32:
- 12 or 24 V supply
- MAX485 RO / DI / DE+RE
- Arduino Uno:
- Software serial and D4
- ESP32:
- GPIO 16 / 17 / 4
Example code
A minimal sketch to check the part works.
#include <ModbusMaster.h>
const int DE_RE = 4;
const uint16_t GAS_REG = 0x0000; // concentration register: check your sensor's manual
const float SCALE = 1.0; // e.g. 10 if the manual says value x10
ModbusMaster node;
void pre() { digitalWrite(DE_RE, HIGH); }
void post() { digitalWrite(DE_RE, LOW); }
void setup() {
Serial.begin(115200);
Serial2.begin(4800, SERIAL_8N1, 16, 17); // Renke default is often 4800; others 9600
pinMode(DE_RE, OUTPUT); post();
node.begin(1, Serial2);
node.preTransmission(pre); node.postTransmission(post);
}
void loop() {
if (node.readHoldingRegisters(GAS_REG, 1) == node.ku8MBSuccess) {
Serial.print("Gas "); Serial.println(node.getResponseBuffer(0) / SCALE, 2);
} else Serial.println("No reply: check address, baud and A/B");
delay(2000);
}Setup and tuning
most run on 12 to 24 V DC.
connect A and B to the RS485 bus, and use shielded twisted pair.
set a unique Modbus address and baud rate for each transmitter.
calibrate with test gas as the manual specifies, often every 6 to 12 months.
mount by gas density: high for light gases, low for heavy gases like LPG.
What you need
Shop this list20 of 20 found in our store · ₹2,11,670
Renke RS-CO-N01-2-1000P Carbon Monoxide Sensor – 0-1000ppm, RS485 Modbus: the part this guide coversRenke RS-CO-N01-2-1000P Carbon Monoxide Sensor – 0-1000ppm, RS485 Modbus₹6,779
Renke RS-CO2-N01-2-5000P Carbon Dioxide Sensor, 0-5000ppm, -40°C to 80°C, RS485 Modbus: another version this guide coversRenke RS-CO2-N01-2-5000P Carbon Dioxide Sensor, 0-5000ppm, -40°C to 80°C, RS485 Modbus₹7,629
Renke RS-CH4-N01-2 Methane Gas Sensor -40℃~+80℃, ±0.06% – RS485 Modbus-RTU: another version this guide coversRenke RS-CH4-N01-2 Methane Gas Sensor -40℃~+80℃, ±0.06% – RS485 Modbus-RTU₹8,339
Renke RS-H2S-N01-2-100P-2 Hydrogen Sulphide & Temperature/Humidity Sensor – RS485 Modbus, Wall Mounted: another version this guide coversRenke RS-H2S-N01-2-100P-2 Hydrogen Sulphide & Temperature/Humidity Sensor – RS485 Modbus, Wall Mounted₹5,719
Renke RS-NH3-N01-2-100P-2-YL-EX Ammonia Gas Sensor – RS485 Modbus, 0-100ppm Range, Wall-Mount: another version this guide coversRenke RS-NH3-N01-2-100P-2-YL-EX Ammonia Gas Sensor – RS485 Modbus, 0-100ppm Range, Wall-Mount₹14,429
Renke RS-NH3-N01-2-50P Ammonia Sensor 0-50ppm – RS485 Modbus Output: another version this guide coversRenke RS-NH3-N01-2-50P Ammonia Sensor 0-50ppm – RS485 Modbus Output₹24,179
Renke RS-NO2-N01-2-20P Nitrogen Dioxide Sensor Module – 0-20ppm, RS485 Modbus, 10-30V DC: another version this guide coversRenke RS-NO2-N01-2-20P Nitrogen Dioxide Sensor Module – 0-20ppm, RS485 Modbus, 10-30V DC₹20,719
Renke RS-O2-N01-30VOL Oxygen Sensor -40℃~+80℃, ±0.3%Vol – RS485 Modbus: another version this guide coversRenke RS-O2-N01-30VOL Oxygen Sensor -40℃~+80℃, ±0.3%Vol – RS485 Modbus₹12,329
Renke RS-O2-N01-30VOL-EX Oxygen Sensor (RS485) – 0-30%VOL Range: another version this guide coversRenke RS-O2-N01-30VOL-EX Oxygen Sensor (RS485) – 0-30%VOL Range₹8,479
Renke RS-O3-N01-2-10P Ozone Sensor -40℃~80℃ 0~10.00ppm, 0-100%RH – RS485 Modbus: another version this guide coversRenke RS-O3-N01-2-10P Ozone Sensor -40℃~80℃ 0~10.00ppm, 0-100%RH – RS485 Modbus₹9,489
Renke RS-SO2-N01-2-20P-JK Sulfur Dioxide Sensor 0-20.00ppm – RS485 Modbus, 0-5V/0-10V/4-20mA Output: another version this guide coversRenke RS-SO2-N01-2-20P-JK Sulfur Dioxide Sensor 0-20.00ppm – RS485 Modbus, 0-5V/0-10V/4-20mA Output₹19,539
Renke RS-SO2-N01-2-20P-JK-EX Sulfur Dioxide Sensor, Range: 0-20ppm – RS485/4-20mA/0-10V Output, IP67 Wall Mount: another version this guide coversRenke RS-SO2-N01-2-20P-JK-EX Sulfur Dioxide Sensor, Range: 0-20ppm – RS485/4-20mA/0-10V Output, IP67 Wall Mount₹24,549
Renke RS-TVOC-N01-2-4 TVOC Sensor 0-60000ppb, -40°C to +85°C, RS485 Output: another version this guide coversRenke RS-TVOC-N01-2-4 TVOC Sensor 0-60000ppb, -40°C to +85°C, RS485 Output₹4,829
Renke RS-CH2O-N01-2-5P-2 Formaldehyde Sensor – RS485 Modbus, 0-5ppm, 10-30V DC: another version this guide coversRenke RS-CH2O-N01-2-5P-2 Formaldehyde Sensor – RS485 Modbus, 0-5ppm, 10-30V DC₹6,889
Renke RS-CH2O-N01-2-5P-2-EX Formaldehyde Sensor (0-5ppm) – RS485/4-20mA/0-10V Output: another version this guide coversRenke RS-CH2O-N01-2-5P-2-EX Formaldehyde Sensor (0-5ppm) – RS485/4-20mA/0-10V Output₹9,269
JXBS-3001-CO-RS-4-JC CO Gas Sensor 1-1000 ppm – RS485 Modbus Wall Mount: another version this guide coversJXBS-3001-CO-RS-4-JC CO Gas Sensor 1-1000 ppm – RS485 Modbus Wall Mount₹2,169
JXBS-3001-YJ-CO-RS CO Gas Sensor – RS485 Modbus, Wall-Mount Industrial Enclosure: another version this guide coversJXBS-3001-YJ-CO-RS CO Gas Sensor – RS485 Modbus, Wall-Mount Industrial Enclosure₹5,459
JXBS-3001-TVOC-RS-6 Wall-Mounted Air Quality Sensor – RS485, 4G, NB-IoT, LoRa: another version this guide coversJXBS-3001-TVOC-RS-6 Wall-Mounted Air Quality Sensor – RS485, 4G, NB-IoT, LoRa₹5,059
King Shell SN-3002-TVOC-N01 TVOC Transmitter (RS485) – 0-60000ppb, 4-20mA/0-5V/0-10V Output, Wall-Mount: another version this guide coversKing Shell SN-3002-TVOC-N01 TVOC Transmitter (RS485) – 0-60000ppb, 4-20mA/0-5V/0-10V Output, Wall-Mount₹2,329
SN-FPC-TVOC-NO1-A Explosion-proof TVOC Transmitter with Display & Alarm – RS485 Modbus, IP66 Wall-Mount: another version this guide coversSN-FPC-TVOC-NO1-A Explosion-proof TVOC Transmitter with Display & Alarm – RS485 Modbus, IP66 Wall-Mount₹13,489
Alternatives and when to choose them
- RS485 temperature humidity sensors: the same bus and code.
- Modbus RTU with Arduino and ESP32: protocol details.
- DFRobot Gravity calibrated: board-level sensors.
Common mistakes to avoid
- Duplicate Modbus addresses.
- Skipping calibration.
- Mounting at the wrong height for the gas.
- No termination on long buses.
Frequently asked questions
How do I read an RS485 gas transmitter?
Use Modbus RTU from a PLC, or an RS485 module with a library on Arduino or ESP32.
How often should gas sensors be calibrated?
Usually every 6 to 12 months with certified test gas.
Where should I mount a CO transmitter?
At breathing height, about 1.5 m, because CO mixes evenly with room air.
Why do I get Modbus timeouts?
Wrong address, baud rate, A/B swapped or missing termination.
Can it trigger a fan or alarm?
Yes, many have relay outputs for alarms and ventilation.
Parts for this guide
- ₹6,779View
- ₹7,629View
- ₹8,339View
Renke RS-H2S-N01-2-100P-2 Hydrogen Sulphide & Temperature/Humidity Sensor – RS485 Modbus, Wall Mounted₹5,719View- ₹14,429View
- ₹24,179View
- ₹20,719View
- ₹12,329View
- ₹8,479View
- ₹9,489View
- ₹19,539View
Renke RS-SO2-N01-2-20P-JK-EX Sulfur Dioxide Sensor, Range: 0-20ppm – RS485/4-20mA/0-10V Output, IP67 Wall Mount₹24,549View- ₹4,829View
- ₹6,889View
- ₹9,269View
- ₹2,169View
- ₹5,459View
- ₹5,059View
King Shell SN-3002-TVOC-N01 TVOC Transmitter (RS485) – 0-60000ppb, 4-20mA/0-5V/0-10V Output, Wall-Mount₹2,329View
SN-FPC-TVOC-NO1-A Explosion-proof TVOC Transmitter with Display & Alarm – RS485 Modbus, IP66 Wall-Mount₹13,489View- ₹2,609View
- ₹11,429View
- ₹389View
- ₹28View
- ₹74View
- ₹298View
- ₹74View
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.







