Component guide · Intermediate · 3 min read
2000W SCR AC Voltage Regulator and Speed Controller

Safe Use and Limits
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
This 2000 W SCR regulator controls 220 V AC loads by phase angle: a knob delays when the thyristors switch on each half cycle, lowering the average voltage. It suits heaters, incandescent lamps, soldering irons and universal brushed motors like drills. It is not for induction motors, fans with capacitors, LED drivers or electronics. Mains voltage is dangerous; enclose it.
Key specs at a glance
- Input
- 220 V AC
- Power
- Up to 2000 W resistive (derate for motors)
- Control
- Potentiometer phase control
- Output range
- About 50 to 220 V AC
- Cooling
- Heatsink required at high load
- Loads
- Resistive and universal motors only
This part is often wired to 230 V mains. Do all wiring with the plug pulled out, keep mains wires inside a closed box with strain relief, add a fuse, and never touch the board while it is plugged in. If you are new to mains wiring, have an electrician check it before you switch on.
What the 2000W SCR AC voltage regulator is
This module is a manual AC power controller: a thyristor (SCR) circuit with a knob that cuts part of every mains half cycle, so a heater, lamp or brushed motor gets less average power.
Phase control chops the sine wave, so the output is not a smooth lower voltage; a normal multimeter may read it wrongly. Inductive loads and induction motors hum, overheat or fail.
For motors, derate to about half the rated power. Use a fuse on the input and put the module in an insulated, ventilated box.
2000W SCR AC voltage regulator pinout
The pins on the 2000W SCR AC voltage regulator and what each one does.
| Pin | Function |
|---|---|
| AC IN | Live and neutral from mains |
| AC OUT | To the load |
| Knob | Output level |
- AC IN
- Live and neutral from mains
- AC OUT
- To the load
- Knob
- Output level
Wiring the 2000W SCR AC voltage regulator
Work only with power disconnected. Earth any metal enclosure.
| 2000W SCR AC voltage regulator pin | Resistive load | Motor load |
|---|---|---|
| Live in | Through a fuse and switch | Same |
| Output | To heater or universal motor | Not for induction motors |
- Live in
- Resistive load:
- Through a fuse and switch
- Motor load:
- Same
- Output
- Resistive load:
- To heater or universal motor
- Motor load:
- Not for induction motors
Example code
A minimal sketch to check the part works.
This module is set by its knob.
To control mains power from a microcontroller, use a zero-cross
detector with a triac driver (opto-isolated) or an SSR designed
for phase control instead.Setup and tuning
fit the module in an insulated, ventilated box with the knob on an insulated shaft; the heatsink and terminals are at mains voltage.
put a fuse or MCB on the live input, rated just above the load current.
mount the heatsink with its fins vertical and leave airflow; above about 1000 W add a fan.
derate to about half the rated power for drills, grinders and other universal motors.
check output with a true-RMS meter and a lamp load before connecting the real appliance.
What you need
Shop this list2 of 2 found in our store · ₹276
220V AC 2000W SCR Voltage Regulator / Speed Controller: the part this guide covers220V AC 2000W SCR Voltage Regulator / Speed Controller₹99
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- Solid-state relay: on/off mains switching.
- PWM DC motor speed controller: for DC motors.
- SSR vs relay.
Common mistakes to avoid
- Using it on induction motors or capacitor fans, which hum, heat and fail.
- Running it on an open bench with exposed mains terminals.
- Leaving out the input fuse.
- Running the full 2000 W with no airflow over the heatsink.
Frequently asked questions
Can it slow down a ceiling fan?
No. Ceiling fans use capacitor induction motors that hum and overheat on phase control. Use a fan regulator made for them.
Can it control a drill or grinder?
Yes. Drills, grinders and mixers use universal brushed motors that work with phase control, but derate to about half the module's power.
Can it dim LED bulbs?
No. LED drivers expect a full sine wave and flicker or fail on chopped AC unless they are marked dimmable for phase-cut dimmers.
Can an Arduino control this module?
Not directly, because it is set by its knob. For microcontroller control use a zero-cross detector with an opto-isolated triac driver.
Why does my multimeter show odd voltages on the output?
The output is a chopped sine wave. Most cheap meters assume a pure sine, so use a true-RMS meter for a correct reading.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
