Component guide · Intermediate · 3 min read
Sensirion SEN50, SEN54, SEN55 and SEN66 All-in-One Environmental Sensor Modules

PM, VOC, NOx, CO2, RH, T)
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Sensirion's SEN5x modules combine a laser particle sensor with gas and climate sensors in one box. The SEN50 measures PM1, PM2.5, PM4 and PM10; the SEN54 adds VOC index, humidity and temperature; the SEN55 adds NOx index. The SEN66 adds a photoacoustic CO2 sensor. One I2C cable gives an indoor air quality monitor with no extra parts.
Key specs at a glance
- Supply
- 5 V (about 70 to 100 mA with the fan)
- Interface
- I2C, address 0x69 (3.3 or 5 V logic)
- PM
- PM1.0, PM2.5, PM4, PM10
- Gas
- VOC index (SEN54, SEN55, SEN66), NOx index (SEN55, SEN66)
- CO2
- SEN66: 0 to 40,000 ppm photoacoustic
- Connector
- 6-pin JST GHR 1.25 mm
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Sensirion SEN55-SDN-T Environmental Sensor PM2.5, CO2, VOC, Temp, RH – I2C Interface₹5,879
Option 2Sensirion SEN50-SDN-T Environmental Sensor Module – PM2.5, Temperature, Humidity, I2C Digital₹2,649
Option 3Sensirion SEN66-SIN-T Environmental Sensor Module | 0 to 40000 ppm CO₂ | I2C Interface₹10,499
Option 4Seeed Studio Grove SEN54 All-in-One Environmental Sensor Module₹5,539
What the Sensirion SEN50, SEN54, SEN55 and SEN66 modules is
Sensirion SEN5x and SEN66 environmental sensor modules combine PM, VOC, NOx, humidity and temperature (and CO2 on SEN66) in one module for air purifiers and air quality monitors.
VOC and NOx are given as an index from 1 to 500 where 100 is the recent average for that room, not as ppm. Values above 100 mean the air is worse than usual.
The fan cleans itself once a week by running at full speed for 10 seconds.
Sensirion SEN50, SEN54, SEN55 and SEN66 modules pinout
The pins on the Sensirion SEN50, SEN54, SEN55 and SEN66 modules and what each one does.
| Pin | Function |
|---|---|
| 1 VDD | 5 V |
| 2 GND | Ground |
| 3 SDA | I2C data |
| 4 SCL | I2C clock |
| 5 SEL | GND for I2C |
| 6 NC | Not connected |
- 1 VDD
- 5 V
- 2 GND
- Ground
- 3 SDA
- I2C data
- 4 SCL
- I2C clock
- 5 SEL
- GND for I2C
- 6 NC
- Not connected
Wiring the Sensirion SEN50, SEN54, SEN55 and SEN66 modules
Connect the Sensirion SEN50, SEN54, SEN55 and SEN66 modules like this.
| Sensirion SEN50, SEN54, SEN55 and SEN66 modules pin | Arduino Uno | ESP32 |
|---|---|---|
| VDD | 5 V | 5 V (VIN) |
| GND | GND | GND |
| SDA | A4 | GPIO 21 |
| SCL | A5 | GPIO 22 |
| SEL | GND | GND |
- VDD
- Arduino Uno:
- 5 V
- ESP32:
- 5 V (VIN)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SDA
- Arduino Uno:
- A4
- ESP32:
- GPIO 21
- SCL
- Arduino Uno:
- A5
- ESP32:
- GPIO 22
- SEL
- Arduino Uno:
- GND
- ESP32:
- GND
Example code
Use the Sensirion SEN66 library for the SEN66, which adds CO2.
#include <SensirionI2CSen5x.h>
SensirionI2CSen5x sen;
void setup() {
Serial.begin(115200);
Wire.begin();
sen.begin(Wire);
sen.deviceReset();
sen.startMeasurement();
}
void loop() {
float pm1, pm25, pm4, pm10, rh, t, voc, nox;
if (!sen.readMeasuredValues(pm1, pm25, pm4, pm10, rh, t, voc, nox)) {
Serial.printf("PM2.5 %.1f ug/m3 RH %.0f%% T %.1f C VOC %.0f NOx %.0f\n", pm25, rh, t, voc, nox);
}
delay(1000);
}Setup and tuning
5 V power and 3.3 V or 5 V I2C as rated, using the supplied cable.
use the Sensirion SEN5x or SEN66 Arduino library.
the fan cleans itself weekly by default.
VOC and NOx indexes need time to learn baseline.
keep inlets clear.
What you need
Shop this list7 of 8 found in our store · ₹27,213
Sensirion SEN55-SDN-T Environmental Sensor PM2.5, CO2, VOC, Temp, RH – I2C Interface: the part this guide coversSensirion SEN55-SDN-T Environmental Sensor PM2.5, CO2, VOC, Temp, RH – I2C Interface₹5,879
Sensirion SEN50-SDN-T Environmental Sensor Module – PM2.5, Temperature, Humidity, I2C Digital: another version this guide coversSensirion SEN50-SDN-T Environmental Sensor Module – PM2.5, Temperature, Humidity, I2C Digital₹2,649
Sensirion SEN66-SIN-T Environmental Sensor Module | 0 to 40000 ppm CO₂ | I2C Interface: another version this guide coversSensirion SEN66-SIN-T Environmental Sensor Module | 0 to 40000 ppm CO₂ | I2C Interface₹10,499
Seeed Studio Studio Grove SEN54 All-in-One Environmental Sensor Module: another version this guide coversSeeed Studio Grove SEN54 All-in-One Environmental Sensor Module₹5,539Closest match, check the specs
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- Uno R3 development board: the controller used in the wiring tableFind this part
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Plantower PMS5003 PM2.5 sensor: to add dust measurementPlantower PMS5003 PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5 V, Range: 0.3~10 µm₹2,119Closest match, check the specs
Alternatives and when to choose them
- PM2.5 dust sensors: particle-only sensors.
- SGP40 and SGP41: the VOC and NOx chips inside.
- SCD4x: CO2 only.
Common mistakes to avoid
- Blocking inlets.
- Expecting VOC ppm values.
- Powering from 3.3 V only.
- Ignoring warm-up.
Frequently asked questions
What does the SEN55 measure?
PM1, PM2.5, PM4, PM10, VOC index, NOx index, humidity and temperature.
Does the SEN66 measure CO2?
Yes. The SEN66 adds an NDIR CO2 sensor to the PM, VOC and NOx readings.
What is the VOC index?
A relative 1 to 500 value showing changes from baseline.
Why are VOC readings strange after start-up?
The VOC algorithm needs hours to learn the room's baseline after start-up.
Can I read it with ESP32?
Yes. Read it over I2C with Sensirion's official library.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

