Component guide · Beginner · 3 min read
Servo Testers and Servo Signal Reverser

Modes, Centring and Use
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A servo tester generates the 50 Hz servo pulse with a knob, so you can move, centre and check servos and ESCs without any code. Most have three modes: manual (knob), neutral (1500 us) and sweep. A servo signal reverser sits in a servo lead and flips the direction, useful when two servos must move in mirror image from one channel.
Key specs at a glance
- Supply
- 4.8 to 6 V
- Output
- PWM about 800 to 2200 us at 50 Hz
- Modes
- Manual, neutral, sweep
- Channels
- 1 to 3 outputs (same signal)
- Reverser
- Inline, flips pulse around 1500 us
- Uses
- Centring, range check, ESC testing
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1RC Servo Motor Tester (3-Channel)₹99
Option 2Servo Tester (Basic, HJ Digital and Hiwonder)₹100
Option 3Servo Signal Reverser Module₹138
What the Servo tester is
A servo tester is a small handheld board that generates servo PWM signals, letting you centre, sweep and check servos and ESCs without a radio or microcontroller.
Use the neutral mode to centre every servo before you fit horns, so arms and steering start straight. Manual mode shows the real range and whether the gears are damaged.
For ESCs, the tester acts as a throttle: start at minimum for arming, then raise slowly with the propeller removed.
Servo tester pinout
The pins on the Servo tester and what each one does.
| Pin | Function |
|---|---|
| Input | 4.8 to 6 V and GND |
| Outputs | Servo connectors |
| Knob | Position in manual mode |
| Button | Mode select |
- Input
- 4.8 to 6 V and GND
- Outputs
- Servo connectors
- Knob
- Position in manual mode
- Button
- Mode select
Wiring the Servo tester
No microcontroller needed. With an ESC, the ESC's BEC can power the tester.
| Servo tester pin | Tester | Reverser |
|---|---|---|
| Power in | 5 V supply or receiver battery | Same |
| Output | Servo or ESC signal lead | Same |
- Power in
- Tester:
- 5 V supply or receiver battery
- Reverser:
- Same
- Output
- Tester:
- Servo or ESC signal lead
- Reverser:
- Same
Example code
Handy when you want to see the exact pulse width the tester gives.
#include <Servo.h>
Servo s;
void setup() { s.attach(9); Serial.begin(9600); }
void loop() {
int us = map(analogRead(A0), 0, 1023, 1000, 2000);
s.writeMicroseconds(us);
Serial.println(us);
delay(20);
}Setup and tuning
feed 4.8 to 6 V from a battery or BEC into the input pins.
plug the servo or ESC signal, power and ground in the right orientation.
use Manual to move with the knob, Neutral to centre at 1500 µs, and Auto to sweep.
use Neutral mode before fitting servo horns.
start at minimum throttle and remove propellers before testing motors.
What you need
Shop this list4 of 5 found in our store · ₹641
RC Servo Motor Tester (3-Channel): the part this guide coversRC Servo Motor Tester (3-Channel)₹99
Servo Tester (Basic, HJ Digital and Hiwonder): another version this guide coversServo Tester (Basic, HJ Digital and Hiwonder)₹100
Servo Signal Reverser Module: another version this guide coversServo Signal Reverser Module₹138- Uno R3 development board: the controller used in the wiring tableFind this part
XL4015 5A buck converter with voltmeter: a separate 5 to 6 V supply for the servosXL4015 5A Buck Converter with Voltmeter₹304
Alternatives and when to choose them
- Servo motors overview.
- ESC guide: testing ESCs safely.
- PWM: the signal itself.
Common mistakes to avoid
- Testing ESCs with props on.
- Reversing servo plugs.
- Feeding too high voltage.
- Leaving servos running against end stops.
Frequently asked questions
How do I centre a servo with a servo tester?
Select Neutral mode, which outputs 1500 µs, then fit the horn.
Can I test an ESC with a servo tester?
Yes, start at minimum throttle and remove the propeller first.
Why does my servo jitter on the tester?
The supply is weak or the servo is worn.
What voltage should I feed the tester?
Usually 4.8 to 6 V, from a battery or BEC.
Can it test several servos at once?
Most have three outputs that all carry the same signal.
Parts for this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

