Component guide · Beginner · 3 min read
Si7021 Humidity and Temperature Sensor

Pinout, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Si7021 from Silicon Labs is an I2C humidity and temperature sensor at address 0x40, sold on the GY-213V module. It measures 0 to 100 % RH with ±3 % accuracy and temperature with ±0.4 °C. It has a built-in heater that dries the sensor after condensation, which makes it useful in damp places such as greenhouses and bathrooms.
Key specs at a glance
- Humidity
- 0 to 100 % RH, ±3 %
- Temperature
- −40 to 125 °C, ±0.4 °C
- Interface
- I2C, address 0x40
- Supply
- 1.9 to 3.6 V chip; GY-213V accepts 3.3 to 5 V
- Heater
- On-chip, programmable current
- Current
- About 150 µA while measuring, under 1 µA asleep
What the Si7021 is
The Si7021 uses a capacitive polymer humidity element and is factory calibrated. Its I2C commands are almost the same as the HTU21D's, so the two are often interchangeable in code.
The on-chip heater warms the sensor a few degrees to evaporate condensation or check that the sensor is working; switch it off again before you take normal readings.
Si7021 pinout
The pins on the Si7021 and what each one does.
| Pin | Function |
|---|---|
| VIN | Supply, 3.3 to 5 V on the GY-213V |
| GND | Ground |
| SCL | I2C clock |
| SDA | I2C data |
- VIN
- Supply, 3.3 to 5 V on the GY-213V
- GND
- Ground
- SCL
- I2C clock
- SDA
- I2C data
Wiring the Si7021
The GY-213V has a regulator and pull-ups, so it connects directly to a 5 V Uno or a 3.3 V ESP32.
| Si7021 pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5V (or 3.3V) | 3V3 |
| GND | GND | GND |
| SDA | A4 | GPIO 21 |
| SCL | A5 | GPIO 22 |
- VCC
- Arduino Uno:
- 5V (or 3.3V)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SDA
- Arduino Uno:
- A4
- ESP32:
- GPIO 21
- SCL
- Arduino Uno:
- A5
- ESP32:
- GPIO 22
Example code
Install "Adafruit Si7021 Library" from the Library Manager. sensor.heater(true) turns the heater on.
#include "Adafruit_Si7021.h"
Adafruit_Si7021 sensor;
void setup() {
Serial.begin(115200);
if (!sensor.begin()) { Serial.println("No Si7021 found"); while (1); }
}
void loop() {
Serial.print(sensor.readTemperature()); Serial.print(" C ");
Serial.print(sensor.readHumidity()); Serial.println(" %RH");
delay(2000);
}Setup and tuning
after long periods above 90 % RH, run the heater for a minute, then wait for the sensor to cool before reading.
away from warm parts on your board.
some low-cost Si7021 modules carry a compatible chip; if accuracy matters, compare against a reference.
What you need
Shop this list4 of 5 found in our store · ₹1,846
GY-213V Si7021 temperature and humidity module: the sensor this guide coversGY-213V-SI7021 Temperature and Humidity Sensor Module – I2C Interface₹1,229Closest match, check the specs- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
16x2 LCD with I2C: to show readings on a character display16×2 LCD with I2C (RG1602A)₹179Closest match, check the specs
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- HTU21D: very similar, same address.
- SHT3x and SHT4x: better accuracy.
- AHT20: low-cost alternative at a different address.
Try it: I2c pullup calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Leaving the heater on during normal readings, so temperature reads high.
- Using it with an HTU21D on the same bus (both 0x40).
- Placing it next to the board's regulator.
- Expecting fast humidity response; it takes several seconds to settle.
Frequently asked questions
What is the Si7021's I2C address?
0x40, fixed.
What is the heater for?
It warms the sensor to dry off condensation and to self-test.
Does it work with 5 V Arduino boards?
The GY-213V module does; the bare chip is 3.3 V.
Can I use HTU21D code?
Usually yes; the basic commands are the same.
How accurate is it?
±3 % RH and ±0.4 °C.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

