Component guide · Beginner · 3 min read
Standard Analog Servos (Futaba S3003, TowerPro SG5010, Emax ES3001, VTS-08A)

Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Standard analog servos like the Futaba S3003, TowerPro SG5010 and Emax ES3001 are the classic 40 x 20 mm RC servos with plastic gears and 3 to 5.5 kg-cm torque. They are smooth, light-duty and cheap, good for steering, small arms and school projects. Drive them with a 50 Hz PWM signal and a separate 5 to 6 V supply.
Key specs at a glance
- Size
- Standard, about 40 x 20 x 38 mm
- Torque
- S3003 3.2, ES3001 4.3, SG5010 5.5, VTS-08A 5 kg-cm (approx.)
- Speed
- About 0.15 to 0.23 s/60 degrees
- Supply
- 4.8 to 6 V
- Gears
- Nylon / plastic
- Signal
- 50 Hz PWM, about 1000 to 2000 us for 90 to 120 degrees
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Futaba S3003 Standard Servo₹211
Option 2TowerPro SG5010 Standard Servo₹215
Option 3Emax ES3001 Standard Servo 4.3kg·cm₹597
Option 4VTS-08A Servo 5kg·cm₹618
What the Standard analog servo is
Analog servos refresh their position only when a pulse arrives, so they hold with less force and a little deadband. That is fine for most hobby uses and keeps current low.
Plastic gears strip if the servo is forced or stalled under load. For arms that lift weight, move up to a metal gear servo such as the MG996R or MG945.
Standard analog servo pinout
The pins on the Standard analog servo and what each one does.
| Pin | Function |
|---|---|
| Brown / black | Ground |
| Red | Supply, 4.8 to 6 V (see specs) |
| Orange / yellow / white | PWM signal, 50 Hz, 500 to 2500 us pulses |
- Brown / black
- Ground
- Red
- Supply, 4.8 to 6 V (see specs)
- Orange / yellow / white
- PWM signal, 50 Hz, 500 to 2500 us pulses
Wiring the Standard analog servo
A standard servo can draw 0.5 to 1 A when starting. Use a separate supply and join grounds.
| Standard analog servo pin | Arduino Uno | ESP32 |
|---|---|---|
| Brown (GND) | GND, also to the servo supply ground | GND, also to the servo supply ground |
| Red (V+) | External 5 to 6 V supply (not the 5V pin for big servos) | External 5 to 6 V supply |
| Signal | D9 | GPIO 18 |
- Brown (GND)
- Arduino Uno:
- GND, also to the servo supply ground
- ESP32:
- GND, also to the servo supply ground
- Red (V+)
- Arduino Uno:
- External 5 to 6 V supply (not the 5V pin for big servos)
- ESP32:
- External 5 to 6 V supply
- Signal
- Arduino Uno:
- D9
- ESP32:
- GPIO 18
Example code
A minimal sketch to check the part works.
#include <Servo.h>
Servo s;
void setup() { s.attach(9); }
void loop() {
int v = analogRead(A0); // 10k pot on A0
s.write(map(v, 0, 1023, 0, 180));
delay(15);
}Setup and tuning
many analog servos move only about 120 degrees at 1000 to 2000 us; widen to 600 to 2400 us carefully.
set 90 degrees before fitting the horn.
keep signal wires away from motor power wires.
What you need
Shop this list8 of 10 found in our store · ₹2,504
Futaba S3003 Standard Servo: the part this guide coversFutaba S3003 Standard Servo₹211
TowerPro SG5010 Standard Servo: another version this guide coversTowerPro SG5010 Standard Servo₹215
Emax ES3001 Standard Servo 4.3kg·cm: another version this guide coversEmax ES3001 Standard Servo 4.3kg·cm₹597
VTS-08A Servo 5kg·cm: another version this guide coversVTS-08A Servo 5kg·cm₹618- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- 16mm rotary potentiometer: a knob to set the servo positionFind this part
XL4015 5A buck converter with voltmeter: a separate 5 to 6 V supply for the servosXL4015 5A Buck Converter with Voltmeter₹304
RC servo motor tester (3-channel): to centre and test servos without codeRC Servo Motor Tester (3-Channel)₹99
Metal servo horn 25T: a stronger horn for 25-tooth spline servosMetal Servo Horn 25T (for MG995 / MG996R)₹71Closest match, check the specs
Alternatives and when to choose them
- MG996R servo: metal gears and higher torque.
- SG90 servo: micro size.
- Metal gear servos MG945 and MG958: stronger standard size.
Common mistakes to avoid
- Stalling the servo and stripping plastic gears.
- Powering from the Arduino 5V pin.
- Fitting the horn before centring.
- Expecting 180 degrees at default pulse widths.
Frequently asked questions
Which is strongest?
The SG5010 and VTS-08A, at about 5 kg-cm.
Can I use them on a robot arm?
Only for light loads; use metal gear servos for lifting joints.
What horn spline?
Futaba S3003 uses a 25T Futaba spline; others vary, check before buying horns.
Why does it jitter?
Noisy supply or shared ground issues; add a capacitor.
Analog vs digital?
Analog is cheaper and lower current; digital holds stronger.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


