Component guide · Intermediate · 3 min read
STEPPERONLINE BLD-305S Digital BLDC Motor Driver

Hall Wiring and Speed Control
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The BLD-305S drives a three-phase brushless DC motor that has Hall sensors, at 12 to 24 V and up to about 8 A (120 W). Speed is set by the onboard pot, an external pot, a 0 to 5 V signal or PWM, with inputs for direction, enable and brake. It is meant for industrial BLDC motors on conveyors, pumps and robots, not drone motors.
Key specs at a glance
- Supply
- 12 to 24 V DC
- Current
- Up to about 8 A, 120 W
- Motor
- 3-phase BLDC with Hall sensors
- Speed input
- Internal pot, external pot, 0 to 5 V, PWM
- Controls
- F/R, EN, BRK
- Output
- Speed pulse signal
This part can carry many amps. Use wire thick enough for the current, put a fuse close to the battery, check that connectors are rated for the load and give drivers and motors room to cool. A short at these currents melts wires in seconds.
What the STEPPERONLINE BLD-305S BLDC driver is
The BLD-305S is a closed-loop speed controller for brushless DC motors that have Hall sensors. It reads the Hall signals to switch the three motor phases and holds a set speed from a pot, a voltage or a PWM input.
Motor phases (U, V, W) and Hall wires must match; a wrong order makes the motor shudder or draw high current. Use the motor maker's wiring table.
Drone BLDC motors without Hall sensors need an ESC instead.
STEPPERONLINE BLD-305S BLDC driver pinout
The pins on the STEPPERONLINE BLD-305S BLDC driver and what each one does.
| Pin | Function |
|---|---|
| V+ / GND | Supply |
| U, V, W | Motor phases |
| Hu, Hv, Hw, +5V, GND | Hall sensors |
| SV | Speed input |
| F/R, EN, BRK | Control inputs |
| PG | Speed pulse out |
- V+ / GND
- Supply
- U, V, W
- Motor phases
- Hu, Hv, Hw, +5V, GND
- Hall sensors
- SV
- Speed input
- F/R, EN, BRK
- Control inputs
- PG
- Speed pulse out
Wiring the STEPPERONLINE BLD-305S BLDC driver
Connect the STEPPERONLINE BLD-305S BLDC driver like this.
| STEPPERONLINE BLD-305S BLDC driver pin | Arduino Uno | ESP32 |
|---|---|---|
| SV | D9 PWM via RC filter, or 0 to 5 V | DAC GPIO 25 via a 3.3-to-5 V amplifier, or PWM |
| F/R | D4 | GPIO 26 |
| EN | D5 | GPIO 27 |
| COM | GND | GND |
- SV
- Arduino Uno:
- D9 PWM via RC filter, or 0 to 5 V
- ESP32:
- DAC GPIO 25 via a 3.3-to-5 V amplifier, or PWM
- F/R
- Arduino Uno:
- D4
- ESP32:
- GPIO 26
- EN
- Arduino Uno:
- D5
- ESP32:
- GPIO 27
- COM
- Arduino Uno:
- GND
- ESP32:
- GND
Example code
Set the driver's speed source switch to external input first. Active levels of EN and F/R vary by version.
const int SV = 9, FR = 4, EN = 5;
void setup() {
pinMode(FR, OUTPUT); pinMode(EN, OUTPUT);
digitalWrite(FR, LOW); digitalWrite(EN, LOW); // check active level in manual
}
void loop() {
for (int s = 0; s <= 255; s += 5) { analogWrite(SV, s); delay(50); }
delay(2000);
analogWrite(SV, 0);
delay(2000);
}Setup and tuning
connect U, V, W and the five Hall wires (+5V, GND, Ha, Hb, Hc) in the order from the motor maker's table.
choose the internal pot or an external input with the selector, then wire 0 to 5 V or PWM from the controller.
set the acceleration and deceleration pots so starts are smooth and the supply is not overloaded.
set it to the motor's rated current so a jam does not overheat the motor.
stop the motor before changing F/R.
What you need
Shop this list3 of 4 found in our store · ₹3,001
STEPPERONLINE Digital BLDC Motor Driver: the part this guide coversSTEPPERONLINE Digital BLDC Motor Driver₹2,689- Uno R3 development board: the controller used in the wiring tableFind this part
SMPS power supply in metal enclosure (5/12/24 V): a 12 or 24 V supplySMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
16mm rotary potentiometer: a knob to set speed16mm Rotary Potentiometer (Linear)₹14Closest match, check the specs
Alternatives and when to choose them
- SimpleFOC mini: gimbal motors and precise control.
- BLDC motors and ESCs.
- ESC guide.
Common mistakes to avoid
- Mixing up the Hall and phase order, so the motor shudders and draws high current.
- Trying to run a sensorless drone motor on it.
- Switching direction while the motor is spinning fast.
- Leaving the current limit at maximum on a small motor.
Frequently asked questions
Can the BLD-305S run sensorless drone motors?
No. It needs Hall sensor signals. Drone and RC motors without Hall sensors need an ESC instead.
Can an Arduino set the speed?
Yes. Feed a 0 to 5 V voltage or a PWM signal into the speed input, and drive F/R, EN and BRK from digital pins.
What supply voltage does it need?
12 to 24 V DC, matched to the motor's rated voltage.
Does it have a brake input?
Yes. The BRK input stops the motor quickly, which helps on conveyors and robot wheels.
Can I read the motor speed back?
Yes. The speed pulse output gives pulses proportional to RPM, which you can count with an interrupt pin.
Parts for this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

