Component guide · Advanced · 3 min read
STM32MP1 Linux Boards

STM32MP135F-DK, STM32MP157F-DK2 Discovery Kits, Seeed ODYSSEY-STM32MP135D and STM32MP157C SoM
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
STM32MP1 chips are microprocessors, not microcontrollers: they run Linux on one or two Cortex-A7 cores. The STM32MP157 adds a Cortex-M4 for real-time tasks next to Linux. The MP135F-DK and MP157F-DK2 kits have touchscreens and boot ST's OpenSTLinux from a microSD card. Seeed's ODYSSEY and SoM boards are for building your own product.
Key specs at a glance
- STM32MP135
- Single Cortex-A7 up to 1 GHz, low cost, dual Ethernet
- STM32MP157
- Dual Cortex-A7 at 800 MHz plus Cortex-M4 at 209 MHz, 3D GPU
- Memory
- 512 MB DDR on the Discovery kits, 4 Gb on ODYSSEY
- Display
- 4.3 inch touch on MP135F-DK, 4 inch DSI touch on MP157F-DK2
- OS
- OpenSTLinux (Yocto), Debian community images
- Boot
- microSD card; eMMC on some boards
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1STM32MP135F-DK Discovery Kit with STM32MP135FAF7₹20,519
Option 2STM32MP157F-DK2 Discovery Kit with STM32MP157FAC1 MPU₹23,049
Option 3Seeed Studio ODYSSEY – STM32MP135D Cortex-A7 SBC 4Gb DRAM₹5,009
Option 4Seeed Studio SoM – STM32MP157C Cortex-A7 + Cortex-M4 Module₹5,999
What the STM32MP1 Linux boards (STM32MP135F-DK, STM32MP157F-DK2, Seeed ODYSSEY and SoM) is
STM32MP1 Linux boards, such as the STM32MP157 Discovery kits and third-party SoMs, combine Arm Cortex-A7 cores running Linux with a Cortex-M4 for real-time tasks.
Flash the starter image with STM32CubeProgrammer, boot the board and log in over the serial console. Use the Cortex-M4 on MP157 for timing-critical work, loaded from Linux with remoteproc.
For a general Linux computer with lots of tutorials, a Raspberry Pi or other SBC is easier. Choose STM32MP1 when you need long-term industrial supply, low power or a real-time co-processor.
STM32MP1 Linux boards (STM32MP135F-DK, STM32MP157F-DK2, Seeed ODYSSEY and SoM) pinout
The pins on the STM32MP1 Linux boards (STM32MP135F-DK, STM32MP157F-DK2, Seeed ODYSSEY and SoM) and what each one does.
| Pin | Function |
|---|---|
| ST-LINK / console USB | Serial console and flashing |
| USB-C | Power and USB OTG |
| Ethernet | One or two ports |
| GPIO header | Raspberry Pi-style 40-pin on DK2 |
| Camera / display | MIPI CSI and DSI on some kits |
- ST-LINK / console USB
- Serial console and flashing
- USB-C
- Power and USB OTG
- Ethernet
- One or two ports
- GPIO header
- Raspberry Pi-style 40-pin on DK2
- Camera / display
- MIPI CSI and DSI on some kits
Wiring the STM32MP1 Linux boards (STM32MP135F-DK, STM32MP157F-DK2, Seeed ODYSSEY and SoM)
GPIO is 3.3V. Shut Linux down before removing power to protect the SD card.
| STM32MP1 Linux boards (STM32MP135F-DK, STM32MP157F-DK2, Seeed ODYSSEY and SoM) pin | Connection | Note |
|---|---|---|
| USB-C | 5V 3A supply | Low supplies cause boot loops |
| Console | ST-LINK USB to PC | 115200 baud |
| Network | Ethernet cable | For package installs |
- USB-C
- Connection:
- 5V 3A supply
- Note:
- Low supplies cause boot loops
- Console
- Connection:
- ST-LINK USB to PC
- Note:
- 115200 baud
- Network
- Connection:
- Ethernet cable
- Note:
- For package installs
Example code
Pin numbers depend on the board. The ST wiki lists every header pin and its gpiochip line.
# list GPIO chips and lines
gpiodetect
gpioinfo gpiochip0 | head
# toggle line 14 of gpiochip0 (pick a free pin from the board's manual)
while true; do
gpioset gpiochip0 14=1; sleep 0.5
gpioset gpiochip0 14=0; sleep 0.5
doneSetup and tuning
flash OpenSTLinux starter package with STM32CubeProgrammer.
set boot mode switches for SD or eMMC.
load M4 firmware from Linux using remoteproc.
use the ST-Link virtual COM port for the Linux console.
use the specified USB-C or DC supply.
What you need
Shop this list6 of 6 found in our store · ₹54,689
STM32MP135F-DK Discovery Kit with STM32MP135FAF7: the part this guide coversSTM32MP135F-DK Discovery Kit with STM32MP135FAF7₹20,519
STM32MP157F-DK2 Discovery Kit with STM32MP157FAC1 MPU: another version this guide coversSTM32MP157F-DK2 Discovery Kit with STM32MP157FAC1 MPU₹23,049
Seeed Studio Studio ODYSSEY – STM32MP135D Cortex-A7 SBC 4Gb DRAM: another version this guide coversSeeed Studio ODYSSEY – STM32MP135D Cortex-A7 SBC 4Gb DRAM₹5,009Closest match, check the specs
Seeed Studio SoM – STM32MP157C Cortex-A7 + Cortex-M4 Module: another version this guide coversSeeed Studio SoM – STM32MP157C Cortex-A7 + Cortex-M4 Module₹5,999
USB cable: for power, flashing and the virtual COM portUSB Cable₹28
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
Alternatives and when to choose them
- Orange Pi and Radxa SBCs: faster general SBCs.
- STM32 Discovery kits: microcontroller kits.
- Edge AI boards: for vision and AI.
Common mistakes to avoid
- Wrong boot switch setting.
- Weak supply.
- Mismatched M4 firmware.
- Skipping the console for debugging.
Frequently asked questions
What is the STM32MP1 good for?
Linux HMIs and gateways that also need real-time control.
How do I run code on the Cortex-M4?
Build it in CubeIDE and load it with remoteproc from Linux.
Which Linux does it run?
It runs ST's OpenSTLinux, based on Yocto, or community Debian builds.
Why does the board not boot?
The boot switches or the SD card image are wrong for the board.
Can I use Qt for HMIs?
Yes. Qt and LVGL both run on the STM32MP1 for touch HMIs.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

