Component guide · Intermediate · 4 min read
Seeed LoRa-E5 (Wio-E5), EByte E77 and STM32WL LoRaWAN Modules

AT Commands
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Seeed LoRa-E5 (now Wio-E5), EByte E77 and similar modules are built on the STM32WLE5, an STM32 microcontroller with a LoRa radio inside. They ship with LoRaWAN AT firmware, so any board with a UART can join The Things Network by sending a few text commands. Advanced users can also program the STM32WL directly with STM32CubeIDE or the Arduino STM32 core.
Key specs at a glance
- Chip
- STM32WLE5JC (Cortex-M4, 256 KB flash, 64 KB RAM, sub-GHz radio)
- Bands
- Version dependent, about 850 to 930 MHz on HF modules
- Output power
- Up to 22 dBm
- Interface
- UART AT commands at 9600 baud (LoRa-E5)
- Supply
- 3.3 V; mini board 3 to 5 V via USB-C
- Sleep
- About 2 uA in deep sleep
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Seeed Studio LoRa-E5 STM32WLE5JC Module w/ SX126X₹1,129
Option 2LoRaE5 mini STM32WLE5JC LoRaWAN Development Board₹2,449
Option 3LoRa-E5 Development Kit with STM32WLE5JC Module₹3,309
Option 4Seeed Wio-E5 Dev Kit (LoRaWAN)₹3,750
Option 5EByte E77-900M22S LoRaWAN Node Module w/ UART & AT Commands₹739
Option 6Macnman MAC32WLE5 LoRaWAN Module STM32WL 868/915MHz₹878
What the Seeed LoRa-E5 and STM32WL LoRaWAN module is
The LoRa-E5 mini is a breakout with USB-C, buttons and an antenna connector, and the Dev Kit adds a battery holder and Grove sockets. The E77, Macnman MAC32WLE5 and Nebulae modules use the same chip with their own AT firmware, so check each maker's command list.
The LilyGO T3 STM32WL55 board uses the dual-core STM32WL55 and is programmed directly rather than with AT commands.
In India the licence-free LoRa band is 865 to 867 MHz (LoRaWAN plan IN865). 433 MHz modules are widely used by hobbyists, but check local rules before a commercial deployment.
Seeed LoRa-E5 and STM32WL LoRaWAN module pinout
The pins on the Seeed LoRa-E5 and STM32WL LoRaWAN module and what each one does.
| Pin | Function |
|---|---|
| TX / RX | UART AT interface |
| 3V3 / GND | Supply |
| RST | Reset |
| BOOT | Bootloader entry for firmware updates |
| SWDIO / SWCLK | Debug and programming |
| RF / IPEX | Antenna |
- TX / RX
- UART AT interface
- 3V3 / GND
- Supply
- RST
- Reset
- BOOT
- Bootloader entry for firmware updates
- SWDIO / SWCLK
- Debug and programming
- RF / IPEX
- Antenna
Wiring the Seeed LoRa-E5 and STM32WL LoRaWAN module
Signals are 3.3 V. The LoRa-E5 mini can also be plugged into a PC over USB-C and driven from a serial terminal, which is the best first test.
| Seeed LoRa-E5 and STM32WL LoRaWAN module pin | Arduino Uno | ESP32 |
|---|---|---|
| 3V3 | 3.3V | 3V3 |
| GND | GND | GND |
| TX | D2 (SoftwareSerial RX) | GPIO 16 (RX2) |
| RX | D3 via divider | GPIO 17 (TX2) |
- 3V3
- Arduino Uno:
- 3.3V
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- TX
- Arduino Uno:
- D2 (SoftwareSerial RX)
- ESP32:
- GPIO 16 (RX2)
- RX
- Arduino Uno:
- D3 via divider
- ESP32:
- GPIO 17 (TX2)
Example code
Replace the AppKey with the one from your network server and register the DevEUI shown by AT+ID. Region names follow Seeed's AT manual; E77 and other modules use their own command names.
HardwareSerial e5(2);
void at(const char* c, int w = 1000) { e5.println(c); delay(w); while (e5.available()) Serial.write(e5.read()); }
void setup() {
Serial.begin(115200);
e5.begin(9600, SERIAL_8N1, 16, 17);
at("AT");
at("AT+ID"); // prints DevEUI to register on TTN
at("AT+DR=IN865"); // region plan
at("AT+MODE=LWOTAA");
at("AT+KEY=APPKEY,\"00112233445566778899AABBCCDDEEFF\"");
at("AT+JOIN", 10000); // wait for +JOIN: Network joined
}
void loop() {
at("AT+CMSGHEX=\"0102\"", 8000); // confirmed uplink, 2 bytes
delay(600000); // every 10 minutes
}Setup and tuning
create an end device on The Things Network or ChirpStack with the DevEUI from AT+ID.
use IN865 in India and make sure the gateway runs the same plan.
STM32CubeProgrammer through the BOOT pin or SWD.
AT+TEST mode sends raw LoRa packets between two modules without a gateway.
What you need
Shop this list14 of 15 found in our store · ₹18,209
Seeed Studio Studio LoRa-E5 STM32WLE5JC Module w/ SX126X: the part this guide coversSeeed Studio LoRa-E5 STM32WLE5JC Module w/ SX126X₹1,129Closest match, check the specs
LoRaE5 mini STM32WLE5JC LoRaWAN Development Board: another version this guide coversLoRaE5 mini STM32WLE5JC LoRaWAN Development Board₹2,449
LoRa-E5 Development Kit with STM32WLE5JC Module: another version this guide coversLoRa-E5 Development Kit with STM32WLE5JC Module₹3,309
Seeed Wio-E5 Dev Kit (LoRaWAN): another version this guide coversSeeed Wio-E5 Dev Kit (LoRaWAN)₹3,750
EByte E77-900M22S LoRaWAN Node Module w/ UART & AT Commands: another version this guide coversEByte E77-900M22S LoRaWAN Node Module w/ UART & AT Commands₹739
Macnman MAC32WLE5 LoRaWAN Module STM32WL 868/915MHz: another version this guide coversMacnman MAC32WLE5 LoRaWAN Module STM32WL 868/915MHz₹878
Macnman MAC32WBLE5 LoRaWAN + BLE 5.0 Dual Wireless Module: another version this guide coversMacnman MAC32WBLE5 LoRaWAN + BLE 5.0 Dual Wireless Module₹1,699
Nebulae NLN500a LoRa Module STM32WL 868MHz: another version this guide coversNebulae NLN500a LoRa Module STM32WL 868MHz₹1,049
LilyGO T3 STM32WL55 LoRa Development Board w/ 0.96-Inch OLED: another version this guide coversLilyGO T3 STM32WL55 LoRa Development Board w/ 0.96-Inch OLED₹2,219
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- Uno R3 development board: the controller used in the wiring tableFind this part
868MHz 4dBi SMA antenna with 3 m cable: an outdoor antenna for 865 to 868 MHzLWC-868-MM-03 868MHz 4dBi SMA Antenna w/ 3m RG58 Cable₹412Closest match, check the specs
IPEX to SMA pigtail cable: to fit an SMA antenna to an IPEX socket5cm RG178 IPEX 1 to RP-SMA Female RF Pigtail Cable₹82Closest match, check the specs
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
4-channel logic level converter (BSS138): to connect 5 V and 3.3 V signals safely4-Channel Logic Level Converter (BSS138)₹20
Alternatives and when to choose them
- Heltec CubeCell: Arduino programmed LoRaWAN node.
- Ai-Thinker Ra-08H: another AT command LoRaWAN module.
- SX1302 LoRaWAN gateway modules: the gateway side.
Common mistakes to avoid
- Joining without registering the DevEUI on the network server.
- Region mismatch between node and gateway.
- 5 V on the RX pin.
- Expecting Seeed AT commands to work on an E77.
Frequently asked questions
Is Wio-E5 the same as LoRa-E5?
Yes, Seeed renamed it.
Can I run my own code on it?
Yes, it is an STM32; program it with STM32CubeIDE or the Arduino STM32 core, which replaces the AT firmware.
Does it work without a gateway?
In AT+TEST mode for point to point; LoRaWAN needs a gateway.
How much power does it use?
A few microamps asleep and about 100 mA while sending at full power.
Which antenna?
An 868 MHz class antenna tuned for 865 to 868 MHz in India.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


