Component guide · Beginner · 3 min read
USB-C PD Trigger and QC Decoy Modules (9V, 12V, 15V, 20V)

Setup and Use
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A USB-C PD trigger (or decoy) board negotiates a higher voltage from a USB Power Delivery charger, such as 9, 12, 15 or 20 V, and outputs it on pads or a cable. It turns a laptop or phone charger into a small fixed bench supply for soldering irons, LED strips and 12 V gadgets. QC decoy modules do the same with Quick Charge chargers.
Key specs at a glance
- Input
- USB-C PD charger (or QC charger for QC decoys)
- Output
- Fixed 5, 9, 12, 15 or 20 V (set by solder bridge, switch or button)
- Current
- Up to the charger's rating, typically 3 A, 5 A with e-marked cable
- Chip
- PDC004 or similar
- Fallback
- 5 V if the charger cannot give the requested voltage
- Indicator
- LED on many boards
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
What the USB-C PD trigger module is
A USB-C PD trigger board talks to a USB Power Delivery charger and asks it for a fixed higher voltage, such as 12 V or 20 V, instead of the default 5 V. It turns a laptop or phone charger into a small fixed power supply.
The charger decides what it can provide. A 20 W phone charger may offer only 9 or 12 V at under 2 A, while a 65 W laptop charger gives 20 V at 3.25 A.
Always check the output with a meter before connecting a device; some boards fall back to 5 V silently.
USB-C PD trigger module pinout
The pins on the USB-C PD trigger module and what each one does.
| Pin | Function |
|---|---|
| USB-C | Input from PD charger |
| VOUT+ / GND | Output pads |
| Select | Solder jumpers or button |
- USB-C
- Input from PD charger
- VOUT+ / GND
- Output pads
- Select
- Solder jumpers or button
Wiring the USB-C PD trigger module
Connect the USB-C PD trigger module like this.
| USB-C PD trigger module pin | PD trigger | QC decoy |
|---|---|---|
| USB-C in | PD charger | QC charger |
| Output | 12 V device | 9 or 12 V device |
- USB-C in
- PD trigger:
- PD charger
- QC decoy:
- QC charger
- Output
- PD trigger:
- 12 V device
- QC decoy:
- 9 or 12 V device
Example code
A minimal sketch to check the part works.
Set the jumper or press the button for the voltage you want,
plug in the charger, measure the output, then connect the load.Setup and tuning
check the charger's label for the voltages it supports (5, 9, 15, 20 V are common; 12 V is optional on many).
set the board's switch, button or solder bridge before connecting the load, and measure the output.
above 3 A use a 5 A e-marked USB-C cable.
the board falls back to 5 V if the charger cannot give the voltage you chose, so check before relying on it.
mark the + and − output wires clearly.
What you need
Shop this list5 of 5 found in our store · ₹1,069
USB-C PD Trigger Board, Fixed Voltage Output: the part this guide coversUSB-C PD Trigger Board, Fixed Voltage Output₹310
USB-C PD Decoy Module PDC004, Fixed Voltage: another version this guide coversUSB-C PD Decoy Module PDC004, Fixed Voltage₹81
QC 2.0 / 3.0 Trigger Decoy Module (9V / 12V / 15V / 20V): another version this guide coversQC 2.0 / 3.0 Trigger Decoy Module (9V / 12V / 15V / 20V)₹252
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
INA219 current and power monitor module: to log voltage and current from the outputINA219 Current and Power Monitor Module₹249
Alternatives and when to choose them
- USB step-down modules: the opposite direction.
- Bench power supply: adjustable.
- USB cables and connectors.
Common mistakes to avoid
- Expecting 20 V from a small phone charger.
- Not checking the fallback voltage before connecting the load.
- Overloading the charger beyond its wattage.
- Using a cheap cable above 3 A.
Frequently asked questions
Can a USB-C PD trigger power a 12 V LED strip?
Yes, if the charger offers 12 V and the strip's power stays within the charger's rating.
Can it run a USB-C soldering iron or 20 V tool?
Yes. Many USB-C irons use 20 V from a 65 W or larger PD charger.
Why do I only get 5 V?
The charger does not support the voltage you selected, or the cable is not passing PD signals.
Is the voltage adjustable?
Only in the fixed PD steps the charger supports. For other voltages add a buck converter after the trigger.
Does it work with Quick Charge chargers?
No. Use the QC decoy module for Quick Charge chargers.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
