Buying guide · Intermediate · 3 min read
Water Quality Sensors
pH, TDS and Turbidity
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
Hobby water quality kits use three common probes. A pH probe measures acidity and needs calibration with buffer solutions. A TDS probe measures electrical conductivity and estimates dissolved solids in ppm. A turbidity sensor shines light through water to judge cloudiness. Each comes with a small board giving an analog voltage. They are excellent for aquariums, hydroponics and teaching, but cannot tell you whether water is safe to drink.
Key specs at a glance
- pH probe
- Glass electrode, 0 to 14 pH, board gives an analog voltage
- TDS probe
- Two-pin conductivity probe, roughly 0 to 1000 ppm on hobby kits
- Turbidity sensor
- IR light and receiver, analog or digital output
- Supply
- 3.3 to 5 V boards (check each)
- Compensation
- pH and TDS both need temperature correction (add a DS18B20)
- Probe care
- pH probes must stay wet in storage solution
pH sensors
A pH probe produces a tiny voltage, about 59 mV per pH unit at 25 °C, around 0 V at pH 7. The interface board amplifies and offsets it to a 0 to 5 V or 0 to 3 V range for an ADC.
Calibrate with at least two buffer solutions, normally pH 7 and pH 4 (or 10): read the voltage in each, then map linearly between them. Rinse the probe in distilled water between buffers. Recalibrate every few weeks, because probes drift and age. Store the tip in storage solution or pH 4 buffer, never in distilled water and never dry.
TDS and conductivity
A TDS probe drives an AC signal between two pins and measures how well the water conducts. Dissolved salts raise conductivity, and the board's formula converts this to an estimated ppm. Conductivity rises roughly 2 % per °C, so measure temperature with a DS18B20 and correct to 25 °C.
Do not leave the TDS probe and pH probe powered in the same container; their signals can interfere. Switch the TDS board off while reading pH, or use isolated boards.
Turbidity and what these numbers mean
A turbidity sensor measures how much light gets through the water: cloudy water blocks more. Hobby modules give a voltage that falls as turbidity rises; convert it with the maker's curve and treat it as relative.
TDS does not detect bacteria, lead or pesticides, and low TDS does not mean safe. Use these sensors for monitoring trends in an aquarium, hydroponic tank or science project, and use lab testing for drinking water.
Try it: ADC resolution calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Skipping pH calibration with buffer solutions.
- Letting the pH probe dry out.
- Ignoring temperature compensation.
- Powering pH and TDS probes together in one container.
- Treating low TDS as proof that water is safe to drink.
Frequently asked questions
How do I calibrate a pH sensor?
Read the voltage in pH 7 and pH 4 buffer solutions, then map readings linearly between those two points.
Does a TDS meter show if water is safe?
No. It measures dissolved salts, not bacteria, heavy metals or pesticides.
How long does a pH probe last?
Typically months to a couple of years, depending on use and storage.
Can I leave the pH probe in water all the time?
Hobby probes are not designed for continuous immersion; they drift faster. Industrial probes are.
Can I use these with ESP32?
Yes, if the board output stays within 3.3 V. Average readings to reduce ADC noise.
Parts for this guide
Search the store for the parts named above, or ask Geeko AI which one fits your project.
Calculators
Terms in this guide
Projects that use it
Put this into practice: 17 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
- DFRobot Gravity pH, TDS and turbidity sensor wikis
- Atlas Scientific pH probe care guide
- WHO Guidelines for Drinking-water Quality
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
