LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsFish care comes down to steady temperature and clean water. The waterproof probe hangs in the tank, the turbidity sensor sits in the filter outflow, and the OLED shows both; when clarity falls below 70 % it is time for a partial water change.
Tick anything you already have and the total updates.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
Shines light through the water gap and measures how much gets through.
Follow the colours: red is power, dark grey is ground, blue is a signal.
aquarium_water_monitor.inoVerify & upload in Electrolark// Aquarium water monitor
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "aquarium-water-monitor"
#include <OneWire.h>
#include <DallasTemperature.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t ONEWIRE_PIN = 2;
const uint8_t TURB_PIN = A0;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float probeC = 0;
int clarityPct = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
const char* statusText = "OK";
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Aquarium"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 14);
oled.print(F("Probe: "));
oled.print(probeC, 1);
oled.print(F(" C"));
oled.setCursor(0, 24);
oled.print(F("Clarity: "));
oled.print(clarityPct);
oled.print(F("%"));
oled.setCursor(0, 56);
oled.print(statusText);
oled.display();
}
void setup() {
Serial.begin(115200);
probes.begin();
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
probeC = readProbeC();
clarityPct = (int)(analogRead(TURB_PIN) * 100L / ADC_MAX);
statusText = (probeC > -100) ? "OK" : "Sensor error";
Serial.print(F("Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.print(F(", Clarity="));
Serial.print(clarityPct);
Serial.print(F("%"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
Shade the sensor gap; stray light adds to the reading.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), DS18B20 Waterproof Temperature Probe – 1m Cable, Asair AZDM01 Turbidity Sensor Module – Analog, 0.96" OLED Display 128x64 (I2C), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (aquarium_water_monitor.ino). Install these libraries first: OneWire, DallasTemperature, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹761 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Drawing text on an I²C display; Optical sensing and calibration references.
Ideas that reuse this build: Heater controller and Lights and air pump schedule. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Probe=26.0C, Clarity=29% Probe=26.0C, Clarity=29%
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.