Component guide · Intermediate · 3 min read
Waveshare RS485 High Torque Bus Servo (Aluminium Case)

Wiring and Control
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Waveshare RS485 bus servo is a high-torque servo in an aluminium case that talks RS485 instead of TTL. RS485 is differential, so long cables and noisy robots are fine. Like other bus servos, each unit has an ID, reports position, load and temperature, and can run as a positional servo or a continuous motor.
Key specs at a glance
- Bus
- RS485 half-duplex (A, B), 1 Mbps default
- Supply
- 12 V nominal (check label)
- Torque
- About 35 kg-cm and higher versions
- Position
- 12-bit magnetic encoder, 360 degrees
- Case
- Aluminium, better heat dissipation
- Feedback
- Position, speed, load, voltage, temperature
What the Waveshare RS485 bus servo is
Waveshare RS485 bus servos are high-torque servos that daisy-chain on an RS485 bus with IDs, reporting position, load and temperature for robot arms and legged robots.
Use it for robot arm shoulders, pan-tilt heads with heavy cameras and mobile robot joints. The metal case keeps it cooler under holding load.
You need an RS485 transceiver between the controller and the servos, or a Waveshare driver board with RS485. A and B must not be swapped.
Waveshare RS485 bus servo pinout
The pins on the Waveshare RS485 bus servo and what each one does.
| Pin | Function |
|---|---|
| V+ | 12 V |
| GND | Ground |
| A | RS485 A (D+) |
| B | RS485 B (D-) |
- V+
- 12 V
- GND
- Ground
- A
- RS485 A (D+)
- B
- RS485 B (D-)
Wiring the Waveshare RS485 bus servo
Add a 120 ohm termination at the far end of long chains.
| Waveshare RS485 bus servo pin | Arduino Uno | ESP32 |
|---|---|---|
| A / B | Via MAX485 module (DE/RE on one pin) | Via MAX485 or RS485 driver board |
| V+ | 12 V supply | 12 V supply |
| GND | Common ground | Common ground |
- A / B
- Arduino Uno:
- Via MAX485 module (DE/RE on one pin)
- ESP32:
- Via MAX485 or RS485 driver board
- V+
- Arduino Uno:
- 12 V supply
- ESP32:
- 12 V supply
- GND
- Arduino Uno:
- Common ground
- ESP32:
- Common ground
Example code
With a plain MAX485 module, the direction pin must switch between send and receive; Waveshare's RS485 boards do this automatically.
#include <SCServo.h>
SMS_STS st;
const int DIR = 4; // MAX485 DE+RE
void setup() {
Serial1.begin(1000000, SERIAL_8N1, 18, 19);
st.pSerial = &Serial1;
pinMode(DIR, OUTPUT);
}
void loop() {
st.WritePosEx(1, 1024, 2000, 50);
delay(2000);
st.WritePosEx(1, 3072, 2000, 50);
delay(2000);
}Setup and tuning
use the Waveshare bus servo adapter or an RS485 module.
set each servo's ID one at a time before chaining.
feed the stated voltage (often 12 V) with enough current.
add termination on long buses.
read position, load and temperature to protect servos.
What you need
Shop this list4 of 4 found in our store · ₹15,718
Waveshare RS485 Bus Servo, High Torque Aluminium Case: the part this guide coversWaveshare RS485 Bus Servo, High Torque Aluminium Case₹14,550
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Waveshare serial bus servo driver board: to drive bus servos from USB or an ESP32Waveshare Serial Bus Servo Driver Board₹481
SMPS power supply in metal enclosure (5/12/24 V): a bench supply for servo projectsSMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
Alternatives and when to choose them
- ST3215 TTL bus servo: cheaper, shorter cables.
- Serial bus servos overview.
- RS485 basics: differential wiring.
Common mistakes to avoid
- Duplicate IDs.
- Weak supply.
- No termination on long buses.
- Ignoring overheat warnings.
Frequently asked questions
How do I set servo IDs?
Connect one servo at a time and write a new ID with the tool.
Why does only one servo move?
All servos still share the same default ID; give each a unique ID.
Can I read servo position?
Yes. Bus servos report position, load, voltage and temperature.
What voltage do they need?
Usually 12 V, but check the label of your servo model.
Can I control them from ESP32?
Yes, with an RS485 module and Waveshare's servo library.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
