Component guide · Intermediate · 3 min read
Waveshare ST3215, SC15 and SC09 Serial Bus Servos

IDs, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Waveshare ST and SC servos are serial bus servos: every servo has an ID and they share one half-duplex UART line, so you can daisy-chain many joints with one cable. You send a target position and speed, and read back position, load, voltage and temperature. The ST3215 gives 30 kg-cm with a 360 degree magnetic encoder; SC09 and SC15 are smaller and cheaper.
Key specs at a glance
- Bus
- TTL half-duplex UART, 1 Mbps default
- Supply
- ST3215 and 40 kg 12 V; SC09 and SC15 6 to 8.4 V (check label)
- Torque
- SC09 2.3, SC15 17, ST3215 30, 40 kg version about 40 kg-cm
- Position
- ST: 4096 steps over 360 degrees; SC: 1024 steps over 300 degrees
- Feedback
- Position, speed, load, voltage, temperature
- Modes
- Servo (position), motor (continuous), step
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Waveshare ST3215 Serial Bus Servo (30kg·cm)₹2,388
Option 2Waveshare SC15 17kg Programmable Serial Bus Servo₹2,100
Option 3Waveshare SC09 Serial Bus Servo₹997
Option 4Waveshare 40kg·cm Metal Serial Bus Servo₹9,923
What the Waveshare ST3215 serial bus servo is
The Waveshare ST3215 is a 30 kg·cm serial bus servo with 360° magnetic encoder feedback, used in robot arms, humanoids and pan-tilt rigs.
Bus servos need a driver board that turns the controller's TX and RX into the single data line. The Waveshare serial bus servo driver board or the general driver board for robots does this and also feeds power to the chain.
Every new servo ships with ID 1. Connect one servo at a time and change its ID before adding the next, or they will all answer together.
Waveshare ST3215 serial bus servo pinout
The pins on the Waveshare ST3215 serial bus servo and what each one does.
| Pin | Function |
|---|---|
| GND | Ground |
| V+ | Servo supply |
| Data | Half-duplex serial (one wire) |
- GND
- Ground
- V+
- Servo supply
- Data
- Half-duplex serial (one wire)
Wiring the Waveshare ST3215 serial bus servo
The Waveshare driver board has an ESP32 socket and USB; you can also use its USB port to set IDs from the PC tool.
| Waveshare ST3215 serial bus servo pin | Arduino Uno | ESP32 with driver board |
|---|---|---|
| Driver board TX/RX | Not suited (needs 1 Mbps and a free UART) | GPIO 18 (RX), GPIO 19 (TX) |
| Driver board power | External supply to the board's DC jack | Same |
| Servo chain | Plug servo to servo with 3-pin cables | Same |
| GND | Common with the controller | Common |
- Driver board TX/RX
- Arduino Uno:
- Not suited (needs 1 Mbps and a free UART)
- ESP32 with driver board:
- GPIO 18 (RX), GPIO 19 (TX)
- Driver board power
- Arduino Uno:
- External supply to the board's DC jack
- ESP32 with driver board:
- Same
- Servo chain
- Arduino Uno:
- Plug servo to servo with 3-pin cables
- ESP32 with driver board:
- Same
- GND
- Arduino Uno:
- Common with the controller
- ESP32 with driver board:
- Common
Example code
Install the SCServo library from Waveshare or Feetech. ST servos use SMS_STS; SC servos use SCSCL.
#include <SCServo.h>
SMS_STS st; // use SCSCL for SC09/SC15
void setup() {
Serial.begin(115200);
Serial1.begin(1000000, SERIAL_8N1, 18, 19);
st.pSerial = &Serial1;
}
void loop() {
st.WritePosEx(1, 1000, 1500, 50); // id, position, speed, accel
delay(1500);
st.WritePosEx(1, 3000, 1500, 50);
delay(1500);
Serial.println(st.ReadPos(1));
}Setup and tuning
use a Waveshare bus servo driver or general driver board.
feed 6 to 12.6 V within the rating.
set unique IDs before chaining.
use servo mode for position or motor mode for continuous rotation.
monitor load and temperature to avoid overheating.
What you need
Shop this list8 of 8 found in our store · ₹16,661
Waveshare ST3215 Serial Bus Servo (30kg·cm): the part this guide coversWaveshare ST3215 Serial Bus Servo (30kg·cm)₹2,388
Waveshare SC15 17kg Programmable Serial Bus Servo: another version this guide coversWaveshare SC15 17kg Programmable Serial Bus Servo₹2,100
Waveshare SC09 Serial Bus Servo: another version this guide coversWaveshare SC09 Serial Bus Servo₹997
Waveshare 40kg·cm Metal Serial Bus Servo: another version this guide coversWaveshare 40kg·cm Metal Serial Bus Servo₹9,923
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Waveshare serial bus servo driver board: to drive bus servos from USB or an ESP32Waveshare Serial Bus Servo Driver Board₹481
SMPS power supply in metal enclosure (5/12/24 V): a bench supply for servo projectsSMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
Alternatives and when to choose them
- Serial bus servos overview: bus vs PWM servos.
- Hiwonder LX bus servos: another protocol family.
- Waveshare RS485 bus servo: long cables and high torque.
Common mistakes to avoid
- Duplicate IDs.
- Overloading.
- Weak supply.
- Over-voltage.
Frequently asked questions
How much torque does the ST3215 have?
About 30 kg·cm of torque at 12 V.
Can it rotate continuously?
Yes. Switch it to motor mode for continuous rotation with speed control.
Why does the servo stop and get hot?
It is overloaded or stalled, so the protection stops it; reduce the load.
Can I read its position?
Yes. The 12-bit magnetic encoder reports position across the full 360°.
Which controller should I use?
A Waveshare bus servo driver or ESP32 general driver board.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
