Component guide · Intermediate · 3 min read
Hiwonder LX-15D, LX-16A and LX-824 Serial Bus Servos

IDs, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Hiwonder LX servos are serial bus servos used in humanoid and hexapod kits. Each has an ID and shares one half-duplex serial line, so a whole robot connects with short daisy-chain cables. They report position, voltage and temperature. The bus servo tester sets IDs and checks servos without a computer, which is the easiest way to prepare a new set.
Key specs at a glance
- Bus
- Half-duplex TTL serial, 115200 baud
- Supply
- 6 to 8.4 V (2S Li-ion)
- Torque
- LX-16A about 17, LX-15D about 17, LX-824 about 24 kg-cm
- Range
- 0 to 240 degrees (1000 steps)
- Feedback
- Position, voltage, temperature
- Modes
- Servo and continuous motor
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Hiwonder Serial Bus Servo (LX-15D and LX-16A)₹2,100
Option 2Hiwonder Serial Bus Servo with Three Connectors₹2,885
Option 3Hiwonder Serial Bus Servo Controller Communication Tester₹4,676
What the Hiwonder LX serial bus servo is
Hiwonder LX serial bus servos, such as the LX-16A and LX-224, are daisy-chained servos with IDs that report position, voltage and temperature over a half-duplex serial bus.
The LX-824 has three connectors so it can sit in the middle of a branch. These servos use Hiwonder's own protocol, not Feetech's, so do not mix them with Waveshare ST servos on one bus.
The controller needs a half-duplex adapter (Hiwonder's controllers include one), or join TX through a 1k resistor and RX directly on the data line for a quick test.
Hiwonder LX serial bus servo pinout
The pins on the Hiwonder LX serial bus servo and what each one does.
| Pin | Function |
|---|---|
| GND | Ground |
| V+ | 6 to 8.4 V |
| Signal | Half-duplex serial data |
- GND
- Ground
- V+
- 6 to 8.4 V
- Signal
- Half-duplex serial data
Wiring the Hiwonder LX serial bus servo
Connect the Hiwonder LX serial bus servo like this.
| Hiwonder LX serial bus servo pin | Arduino Uno | ESP32 |
|---|---|---|
| Signal | D1/D0 via half-duplex adapter (or LSC controller) | GPIO 17 TX via 1k + GPIO 16 RX on the same line |
| V+ | 2S battery or 7.4 V supply | Same |
| GND | Common | Common |
- Signal
- Arduino Uno:
- D1/D0 via half-duplex adapter (or LSC controller)
- ESP32:
- GPIO 17 TX via 1k + GPIO 16 RX on the same line
- V+
- Arduino Uno:
- 2S battery or 7.4 V supply
- ESP32:
- Same
- GND
- Arduino Uno:
- Common
- ESP32:
- Common
Example code
Position runs 0 to 1000 for 0 to 240 degrees. Hiwonder also provides an Arduino library.
void moveServo(uint8_t id, uint16_t pos, uint16_t ms) {
uint8_t b[10] = {0x55, 0x55, id, 7, 1, (uint8_t)pos, (uint8_t)(pos >> 8), (uint8_t)ms, (uint8_t)(ms >> 8), 0};
uint8_t sum = 0;
for (int i = 2; i < 9; i++) sum += b[i];
b[9] = ~sum;
Serial2.write(b, 10);
}
void setup() { Serial2.begin(115200, SERIAL_8N1, 16, 17); }
void loop() { moveServo(1, 200, 800); delay(1000); moveServo(1, 800, 800); delay(1000); }Setup and tuning
use the Hiwonder bus servo controller or a half-duplex adapter; a normal UART needs a tri-state buffer circuit.
connect one servo at a time and give each a unique ID before chaining them.
feed 6 to 8.4 V at enough current for all servos.
set servo mode for positions, or motor mode for continuous rotation.
read back position and temperature to detect stalls.
What you need
Shop this list6 of 6 found in our store · ₹10,433
Hiwonder Serial Bus Servo (LX-15D and LX-16A): the part this guide coversHiwonder Serial Bus Servo (LX-15D and LX-16A)₹2,100
Hiwonder Serial Bus Servo with Three Connectors: another version this guide coversHiwonder Serial Bus Servo with Three Connectors₹2,885
Hiwonder Serial Bus Servo Controller Communication Tester: another version this guide coversHiwonder Serial Bus Servo Controller Communication Tester₹4,676
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
SMPS power supply in metal enclosure (5/12/24 V): a bench supply for servo projectsSMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
Alternatives and when to choose them
- Waveshare ST3215: Feetech protocol, 360 degree encoder.
- Hiwonder LSC controller: for PWM servos.
- Serial bus servos overview.
Common mistakes to avoid
- Chaining servos before setting unique IDs.
- Wiring the bus to a normal UART without a half-duplex circuit.
- Using a weak supply.
- Ignoring overheating warnings.
Frequently asked questions
How do I set the servo ID?
Connect one servo at a time and write a new ID with the app or library.
Can I connect LX servos to Arduino directly?
Only through a half-duplex circuit or the Hiwonder controller.
Why does only one servo respond?
All servos still share the default ID of 1; give each a unique ID.
Can bus servos rotate continuously?
Yes, in motor mode with speed control.
Can I read the servo position?
Yes. Bus servos report position, voltage and temperature.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
