Component guide · Intermediate · 3 min read
Waveshare Serial Bus Servo Driver Board

Wiring, USB and ESP32 Use
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Waveshare serial bus servo driver board connects ST and SC bus servos to a PC or a microcontroller. It converts TX and RX into the single half-duplex data line, feeds power from its DC jack to the servo chain, and has a USB port for the Feetech or Waveshare PC tool. A jumper selects USB mode or ESP32/UART mode.
Key specs at a glance
- Servos
- Waveshare ST and SC series (Feetech protocol)
- Power in
- DC jack, 6 to 12.6 V to match the servos
- Interfaces
- USB (CH343) and TTL UART
- Mode switch
- Jumper for USB or UART/ESP32 control
- Outputs
- Multiple 3-pin bus connectors
- Max servos
- Up to 253 IDs (limited by supply current)
What the Waveshare serial bus servo driver board is
Waveshare serial bus servo driver boards connect ST and SC series bus servos to a PC, ESP32 or Raspberry Pi, handling the half-duplex bus and power.
Use USB mode first: connect a single servo, open the PC debug tool, set its ID and middle position, then repeat for each servo. Switch the jumper to UART mode to control the chain from an ESP32 or other board.
The board passes the supply voltage straight to the servos. Choose the supply by the servo's rating, not the board's.
Waveshare serial bus servo driver board pinout
The pins on the Waveshare serial bus servo driver board and what each one does.
| Pin | Function |
|---|---|
| DC IN | Servo supply |
| USB-C | PC connection |
| TX / RX / GND | UART to a controller |
| Servo ports | Daisy-chain bus servos |
| Mode jumper | USB or UART |
- DC IN
- Servo supply
- USB-C
- PC connection
- TX / RX / GND
- UART to a controller
- Servo ports
- Daisy-chain bus servos
- Mode jumper
- USB or UART
Wiring the Waveshare serial bus servo driver board
Connect the Waveshare serial bus servo driver board like this.
| Waveshare serial bus servo driver board pin | Arduino Uno | ESP32 |
|---|---|---|
| TX / RX | Not recommended | GPIO 19 / GPIO 18 |
| GND | GND | GND |
| DC IN | Servo supply | Servo supply |
- TX / RX
- Arduino Uno:
- Not recommended
- ESP32:
- GPIO 19 / GPIO 18
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- DC IN
- Arduino Uno:
- Servo supply
- ESP32:
- Servo supply
Example code
A minimal sketch to check the part works.
#include <SCServo.h>
SMS_STS st;
void setup() {
Serial.begin(115200);
Serial1.begin(1000000, SERIAL_8N1, 18, 19);
st.pSerial = &Serial1;
for (int id = 1; id < 20; id++) {
if (st.Ping(id) != -1) { Serial.print("Found ID "); Serial.println(id); }
}
}
void loop() {}Setup and tuning
feed servo power to the board's DC input.
connect USB to a PC for the debug tool, or UART to a microcontroller.
use Waveshare's servo debug software to set IDs and test.
set the jumper for USB or UART mode.
share ground with the controller.
What you need
Shop this list3 of 3 found in our store · ₹1,168
Waveshare Serial Bus Servo Driver Board: the part this guide coversWaveshare Serial Bus Servo Driver Board₹481
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
SMPS power supply in metal enclosure (5/12/24 V): a bench supply for servo projectsSMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
Alternatives and when to choose them
- ST3215 bus servos.
- Waveshare general driver board for robots: adds DC motors and an IMU.
- Serial bus servos overview.
Common mistakes to avoid
- Wrong jumper mode.
- No servo power.
- Duplicate IDs.
- No common ground.
Frequently asked questions
How do I set IDs on bus servos?
Use the servo debug tool with one servo connected at a time.
Can I use the driver with Raspberry Pi?
Yes. Connect over USB or UART and use Waveshare's Python library.
Why does the tool not find servos?
Wrong baud rate, jumper mode or no servo power.
How many servos can be chained?
Dozens can be chained, limited by power supply current and bus speed.
Does the driver power the servos?
Yes. Servo power comes from the board's DC input.
Parts for this guide
Projects that use it
Put this into practice: 7 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
