Component guide · Beginner · 3 min read
Winsen MP503, MP801, MP901, MP905 Air Quality Sensors, ZP07-MP503 Module

ZM102 and Grove Air Quality v1.3
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The MP503, MP801, MP901 and MP905 are low-power metal-oxide sensors for indoor air quality: smoke, cooking fumes, alcohol, formaldehyde and other VOCs. They are used in air purifiers to decide fan speed. The ZP07-MP503 module outputs a 0 to 3 pollution grade over UART, the Grove v1.3 board gives an analog value, and the ZM102 is an automotive version.
Key specs at a glance
- Heater
- About 5 V, 30 to 120 mW by model
- Detects
- VOC, smoke, alcohol, formaldehyde, toluene
- Output
- Analog (bare, Grove), UART grade 0 to 3 (ZP07), LIN/PWM (ZM102)
- Warm-up
- About 3 minutes
- Use
- Purifiers, fresh-air systems, cooker hoods
- Supply
- 5 V
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Seeed Studio Grove Air Quality Sensor v1.3 – Winsen MP503 Module w/ Grove Cable₹1,099
Option 2Winsen ZP07-MP503 Air Quality Detection Module – TTL Output, XH2.54-4P Terminal₹439
Option 3Winsen MP801 Air-Quality Gas Sensor – Semiconductor VOC Detection₹219
Option 4Winsen MP901 Air-Quality Gas Sensor – Metal Cap Encapsulation₹359
Option 5Winsen MP905 Air-Quality Gas Sensor – Semiconductor VOC Detector₹193
Option 6Winsen ZM102 Air Quality Sensor Module – LIN/PWM Output, IP6K6K₹1,319
What the Winsen MP503, MP801, MP901 and MP905 air quality sensors is
The Winsen MP503 is a metal-oxide air quality sensor that responds to alcohol, smoke, formaldehyde, toluene and other VOCs, used in air purifiers and indoor monitors.
These sensors report relative air quality, not ppm of a specific gas. Treat clean air as level 0 and act on rises.
The ZP07-MP503 handles warm-up and baseline itself, so it is the easiest way to drive a purifier.
Winsen MP503, MP801, MP901 and MP905 air quality sensors pinout
The pins on the Winsen MP503, MP801, MP901 and MP905 air quality sensors and what each one does.
| Pin | Function |
|---|---|
| VCC / GND | 5 V supply |
| AO / SIG | Analog (Grove, bare) |
| TX / A, B | UART or grade outputs (ZP07) |
- VCC / GND
- 5 V supply
- AO / SIG
- Analog (Grove, bare)
- TX / A, B
- UART or grade outputs (ZP07)
Wiring the Winsen MP503, MP801, MP901 and MP905 air quality sensors
Connect the Winsen MP503, MP801, MP901 and MP905 air quality sensors like this.
| Winsen MP503, MP801, MP901 and MP905 air quality sensors pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5 V | 5 V (VIN) |
| GND | GND | GND |
| Analog out | A0 | GPIO 34 via divider |
| ZP07 TX | D10 | GPIO 16 |
- VCC
- Arduino Uno:
- 5 V
- ESP32:
- 5 V (VIN)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- Analog out
- Arduino Uno:
- A0
- ESP32:
- GPIO 34 via divider
- ZP07 TX
- Arduino Uno:
- D10
- ESP32:
- GPIO 16
Example code
A minimal sketch to check the part works.
int baseline;
void setup() {
Serial.begin(115200);
delay(180000);
baseline = analogRead(A0);
}
void loop() {
int d = analogRead(A0) - baseline;
const char *lvl = d > 400 ? "very bad" : d > 200 ? "bad" : d > 70 ? "fair" : "fresh";
Serial.print(d); Serial.print(" "); Serial.println(lvl);
delay(1000);
}Setup and tuning
feed the heater at the rated voltage (about 5 V).
read the load-resistor voltage with an analog pin.
burn in for 24 to 48 hours first; allow a few minutes each start.
treat readings as a relative air quality level, not ppm.
keep away from direct airflow and alcohol sprays.
What you need
Shop this list9 of 11 found in our store · ₹4,270
Seeed Studio Studio Grove Air Quality Sensor v1.3 – Winsen MP503 Module w/ Grove Cable: the part this guide coversSeeed Studio Grove Air Quality Sensor v1.3 – Winsen MP503 Module w/ Grove Cable₹1,099
Winsen ZP07-MP503 Air Quality Detection Module – TTL Output, XH2.54-4P Terminal: another version this guide coversWinsen ZP07-MP503 Air Quality Detection Module – TTL Output, XH2.54-4P Terminal₹439
Winsen MP801 Air-Quality Gas Sensor – Semiconductor VOC Detection: another version this guide coversWinsen MP801 Air-Quality Gas Sensor – Semiconductor VOC Detection₹219
Winsen MP901 Air-Quality Gas Sensor – Metal Cap Encapsulation: another version this guide coversWinsen MP901 Air-Quality Gas Sensor – Metal Cap Encapsulation₹359
Winsen MP905 Air-Quality Gas Sensor – Semiconductor VOC Detector: another version this guide coversWinsen MP905 Air-Quality Gas Sensor – Semiconductor VOC Detector₹193
Winsen ZM102 Air Quality Sensor Module – LIN/PWM Output, IP6K6K: another version this guide coversWinsen ZM102 Air Quality Sensor Module – LIN/PWM Output, IP6K6K₹1,319- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- USB 12 V DC fan PWM speed controller: ventilation driven by the readingFind this part
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
MQ-135 air quality sensor module: a low-cost general air quality sensorMQ-135 Air Quality & Gas Detector Sensor Module for Arduino – Analog & TTL Output₹114Closest match, check the specs
Alternatives and when to choose them
- MQ-135 sensor: similar use, higher heater power.
- VOC indoor air quality sensors: digital VOC sensors.
- AGS10 and AGS02MA: I2C TVOC.
Common mistakes to avoid
- Expecting ppm readings.
- Reading before warm-up.
- Placing near alcohol sprays.
- Ignoring humidity effects.
Frequently asked questions
What gases does the MP503 detect?
It reacts to alcohol, smoke, formaldehyde, toluene and other VOCs.
Can it give exact ppm values?
No. It shows relative air quality levels, not exact ppm.
Why do readings change with humidity?
Metal-oxide sensors are affected by humidity and temperature.
How long does it need to warm up?
A day or two for burn-in, then minutes each start.
Is it used in air purifiers?
Yes. Air purifiers use it to change fan speed when air quality drops.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


